View DS33R11_1234308.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
www.maxim-ic.com
GENERAL DESCRIPTION
The DS33R11 extends a 10/100 Ethernet LAN segment by encapsulating MAC frames in HDLC or X.86 (LAPS) for transmission over a T1/E1/J1 data stream. The device performs store-and-forward of packets with full wire-speed transport capability. The built-in Committed Information Rate (CIR) Controller provides fractional bandwidth allocation up to the line rate in increments of 512kbps. The DS33R11 can operate with an inexpensive external processor.
FEATURES

10/100 IEEE 802.3 Ethernet MAC (MII and RMII) Half/Full Duplex with Automatic Flow Control Integrated T1/E1/J1 Framer and LIU HDLC/LAPS Encapsulation with Programmable FCS and Interframe Fill Committed Information Rate Controller Provides Fractional Allocations in 512kbps Increments Programmable BERT for Serial (TDM) Interface External 16MB, 100MHz SDRAM Buffering Parallel Microprocessor Interface 1.8V, 3.3V Supplies Reference Design Routes on Two Signal Layers IEEE 1149.1 JTAG Support
APPLICATIONS
Transparent LAN Service LAN Extension Ethernet Delivery Over T1/E1/J1
FUNCTIONAL DIAGRAM
T1/E1/J1 TRANSCEIVER T1/E1 LINE
Features continued on page 11.
SERIAL STREAM
ORDERING INFORMATION
PART DS33R11 TEMP RANGE -40C to +85C PIN-PACKAGE 256 BGA
BERT
HDLC/X.86 MAPPER
mC
SDRAM
10/100 MAC
MII/RMII
10/100 ETHERNET PHY
DS33R11
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 338
REV: 072105
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
TABLE OF CONTENTS
1 2 DESCRIPTION ...............................................................................................................................9 FEATURE HIGHLIGHTS .............................................................................................................. 11 2.1 GENERAL.................................................................................................................................. 11 2.2 MICROPROCESSOR INTERFACE .................................................................................................. 11 2.3 HDLC ETHERNET MAPPING....................................................................................................... 11 2.4 X.86 (LINK ACCESS PROTOCOL FOR SONET/SDH) ETHERNET MAPPING .................................... 11 2.5 ADDITIONAL HDLC CONTROLLERS IN THE INTEGRATED T1/E1/J1 TRANSCEIVER .......................... 12 2.6 COMMITTED INFORMATION RATE (CIR) CONTROLLER.................................................................. 12 2.7 SDRAM INTERFACE.................................................................................................................. 12 2.8 MAC INTERFACE....................................................................................................................... 12 2.9 T1/E1/J1 LINE INTERFACE......................................................................................................... 13 2.10 CLOCK SYNTHESIZER ................................................................................................................ 13 2.11 JITTER ATTENUATOR ................................................................................................................. 13 2.12 T1/E1/J1 FRAMER .................................................................................................................... 14 2.13 TDM BUS ................................................................................................................................. 14 2.14 TEST AND DIAGNOSTICS ............................................................................................................ 15 2.15 SPECIFICATIONS COMPLIANCE ................................................................................................... 16 3 APPLICATIONS ........................................................................................................................... 17 4 5 6 7 ACRONYMS AND GLOSSARY.................................................................................................... 18 MAJOR OPERATING MODES..................................................................................................... 19 BLOCK DIAGRAMS..................................................................................................................... 20
PIN DESCRIPTIONS .................................................................................................................... 25 7.1 PIN FUNCTIONAL DESCRIPTION .................................................................................................. 25 8 FUNCTIONAL DESCRIPTION ..................................................................................................... 41 8.1 PROCESSOR INTERFACE .................................................................................................... 42
8.1.1 8.1.2 8.1.3 Read-Write / Data Strobe Modes ........................................................................................................42 Clear on Read .....................................................................................................................................42 Interrupt and Pin Modes ......................................................................................................................42
9
ETHERNET MAPPER .................................................................................................................. 43 9.1 ETHERNET MAPPER CLOCKS ..................................................................................................... 43
9.1.1 9.1.2 Ethernet Interface Clock Modes ..........................................................................................................45 Serial Interface Clock Modes ..............................................................................................................45
9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13
RESETS AND LOW POWER MODES ............................................................................................. 46 INITIALIZATION AND CONFIGURATION .......................................................................................... 47 GLOBAL RESOURCES ................................................................................................................ 47 PER-PORT RESOURCES ............................................................................................................ 47 DEVICE INTERRUPTS ................................................................................................................. 48 INTERRUPT INFORMATION REGISTERS ........................................................................................ 50 STATUS REGISTERS .................................................................................................................. 50 INFORMATION REGISTERS.......................................................................................................... 50 SERIAL INTERFACE .................................................................................................................... 50 CONNECTIONS AND QUEUES...................................................................................................... 51 ARBITER ................................................................................................................................... 52 FLOW CONTROL........................................................................................................................ 53
9.13.1 Full Duplex Flow Control .....................................................................................................................54 9.13.2 Half Duplex Flow Control.....................................................................................................................55 9.13.3 Host-Managed Flow Control................................................................................................................55 2 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.14 ETHERNET INTERFACE PORT...................................................................................................... 56
9.14.1 DTE and DCE Mode............................................................................................................................58
9.15 ETHERNET MAC ....................................................................................................................... 59
9.15.1 MII Mode Options ................................................................................................................................61 9.15.2 RMII Mode...........................................................................................................................................61 9.15.3 PHY MII Management Block and MDIO Interface...............................................................................62
9.16 BERT IN THE ETHERNET MAPPER .............................................................................................. 62
9.16.1 9.16.2 9.16.3 9.16.4 Receive Data Interface........................................................................................................................63 Repetitive Pattern Synchronization .....................................................................................................64 Pattern Monitoring ...............................................................................................................................64 Pattern Generation ..............................................................................................................................64
9.17 TRANSMIT PACKET PROCESSOR ................................................................................................ 65 9.18 RECEIVE PACKET PROCESSOR .................................................................................................. 66 9.19 X.86 ENCODING AND DECODING ................................................................................................ 68 9.20 COMMITTED INFORMATION RATE CONTROLLER ............................................................. 71 10 INTEGRATED T1/E1/J1 TRANSCEIVER ..................................................................................... 72 10.1 T1/E1/J1 CLOCKS .................................................................................................................... 72 10.2 PER-CHANNEL OPERATION........................................................................................................ 73 10.3 T1/E1/J1 TRANSCEIVER INTERRUPTS ........................................................................................ 73 10.4 T1 FRAMER/FORMATTER CONTROL AND STATUS ........................................................... 74
10.4.1 T1 Transmit Transparency ..................................................................................................................74 10.4.2 AIS-CI and RAI-CI Generation and Detection .....................................................................................74 10.4.3 T1 Receive-Side Digital-Milliwatt Code Generation ............................................................................75
10.5 E1 FRAMER/FORMATTER CONTROL AND STATUS ........................................................................ 76
10.5.1 Automatic Alarm Generation ...............................................................................................................77
10.6 PER-CHANNEL LOOPBACK ......................................................................................................... 77 10.7 ERROR COUNTERS.................................................................................................................... 78
10.7.1 10.7.2 10.7.3 10.7.4 Line-Code Violation Counter (TR.LCVCR)..........................................................................................78 Path Code Violation Count Register (TR.PCVCR)..............................................................................79 Frames Out-of-Sync Count Register (TR.FOSCR) .............................................................................80 E-Bit Counter (TR.EBCR)....................................................................................................................80
10.8 DS0 MONITORING FUNCTION..................................................................................................... 81 10.9 SIGNALING OPERATION.............................................................................................................. 82
10.9.1 10.9.2 10.9.3 10.9.4 Processor-Based Receive Signaling...................................................................................................82 Hardware-Based Receive Signaling....................................................................................................83 Processor-Based Transmit Signaling..................................................................................................84 Hardware-Based Transmit Signaling...................................................................................................85
10.10 PER-CHANNEL IDLE CODE GENERATION..................................................................................... 86
10.10.1 Idle-Code Programming Examples .....................................................................................................87
10.11 CHANNEL BLOCKING REGISTERS................................................................................................ 88 10.12 ELASTIC STORES OPERATION .................................................................................................... 88
10.12.1 Receive Elastic Store ..........................................................................................................................88 10.12.2 Transmit Elastic Store .........................................................................................................................89 10.12.3 Elastic Stores Initialization...................................................................................................................89 10.12.4 Minimum Delay Mode..........................................................................................................................89
10.13 G.706 INTERMEDIATE CRC-4 UPDATING (E1 MODE ONLY) ......................................................... 90 10.14 T1 BIT-ORIENTED CODE (BOC) CONTROLLER............................................................................ 91
10.14.1 Transmit BOC......................................................................................................................................91
10.15 RECEIVE BOC .......................................................................................................................... 91 10.16 ADDITIONAL (SA) AND INTERNATIONAL (SI) BIT OPERATION (E1 ONLY) ........................................ 92
10.16.1 Method 1: Internal Register Scheme Based on Double-Frame...........................................................92 10.16.2 Method 2: Internal Register Scheme Based on CRC4 Multiframe ......................................................92
10.17 ADDITIONAL HDLC CONTROLLERS IN T1/E1/J1 TRANSCEIVER .................................................... 93
10.17.1 HDLC Configuration ............................................................................................................................93 10.17.2 FIFO Control........................................................................................................................................95 3 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver 10.17.3 HDLC Mapping....................................................................................................................................95 10.17.4 FIFO Information .................................................................................................................................96 10.17.5 Receive Packet-Bytes Available .........................................................................................................96
10.18 LEGACY FDL SUPPORT (T1 MODE)............................................................................................ 97
10.18.1 Overview .............................................................................................................................................97 10.18.2 Receive Section ..................................................................................................................................97 10.18.3 Transmit Section .................................................................................................................................98
10.19 D4/SLC-96 OPERATION ............................................................................................................ 98 10.20 PROGRAMMABLE IN-BAND LOOP CODE GENERATION AND DETECTION.......................................... 99 10.21 LINE INTERFACE UNIT (LIU) ..................................................................................................... 100
10.21.1 LIU Operation ....................................................................................................................................100 10.21.2 Receiver ............................................................................................................................................100 10.21.3 Transmitter ........................................................................................................................................102
10.22 MCLK PRESCALER ................................................................................................................. 103 10.23 JITTER ATTENUATOR ............................................................................................................... 103 10.24 CMI (CODE MARK INVERSION) OPTION .................................................................................... 103 10.25 RECOMMENDED CIRCUITS........................................................................................................ 104 10.26 T1/E1/J1 TRANSCEIVER BERT FUNCTION ........................................................................108
10.26.1 BERT Status......................................................................................................................................108 10.26.2 BERT Mapping ..................................................................................................................................108 10.26.3 BERT Repetitive Pattern Set.............................................................................................................110 10.26.4 BERT Bit Counter..............................................................................................................................110 10.26.5 BERT Error Counter ..........................................................................................................................110 10.26.6 BERT Alternating Word-Count Rate .................................................................................................110
10.27 PAYLOAD ERROR-INSERTION FUNCTION (T1 MODE ONLY)......................................................... 111
10.27.1 Number-of-Errors Registers ..............................................................................................................111
10.28 PROGRAMMABLE BACKPLANE CLOCK SYNTHESIZER.................................................................. 112 10.29 FRACTIONAL T1/E1 SUPPORT.................................................................................................. 112 10.30 T1/E1/J1 TRANSMIT FLOW DIAGRAMS ..................................................................................... 113 11 DEVICE REGISTERS................................................................................................................. 117 11.1 REGISTER BIT MAPS................................................................................................................ 118
11.1.1 11.1.2 11.1.3 11.1.4 11.1.5 11.1.6 Global Ethernet Mapper Register Bit Map.........................................................................................118 Arbiter Register Bit Map ....................................................................................................................119 BERT Register Bit Map .....................................................................................................................119 Serial Interface Register Bit Map.......................................................................................................120 Ethernet Interface Register Bit Map ..................................................................................................122 MAC Register Bit Map.......................................................................................................................123
11.2 GLOBAL REGISTER DEFINITIONS FOR ETHERNET MAPPER ......................................................... 130 11.3 ARBITER REGISTERS ............................................................................................................... 139
11.3.1 Arbiter Register Bit Descriptions .......................................................................................................139
11.4 BERT REGISTERS .................................................................................................................. 140 11.5 SERIAL INTERFACE REGISTERS ................................................................................................ 147
11.5.1 11.5.2 11.5.3 11.5.4 11.5.5 Serial Interface Transmit and Common Registers ............................................................................147 Serial Interface Transmit Register Bit Descriptions...........................................................................147 Transmit HDLC Processor Registers ................................................................................................148 X.86 Registers...................................................................................................................................155 Receive Serial Interface ....................................................................................................................157
11.6 ETHERNET INTERFACE REGISTERS........................................................................................... 170
11.6.1 Ethernet Interface Register Bit Descriptions .....................................................................................170 11.6.2 MAC Registers ..................................................................................................................................182
11.7 T1/E1/J1 TRANSCEIVER REGISTERS ........................................................................................ 197
11.7.1 Number-of-Errors Left Register.........................................................................................................293
12 FUNCTIONAL TIMING ............................................................................................................... 294 12.1 FUNCTIONAL SERIAL I/O TIMING............................................................................................... 294
4 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
12.2 MII AND RMII INTERFACES ...................................................................................................... 295 12.3 TRANSCEIVER T1 MODE FUNCTIONAL TIMING ........................................................................... 297 12.4 E1 MODE ...............................................................................................................................302 13 OPERATING PARAMETERS ..................................................................................................... 307 13.1 THERMAL CHARACTERISTICS ................................................................................................... 308 13.2 MII INTERFACE........................................................................................................................ 309 13.3 RMII INTERFACE ..................................................................................................................... 311 13.4 MDIO INTERFACE ................................................................................................................... 313 13.5 TRANSMIT WAN INTERFACE .................................................................................................... 314 13.6 RECEIVE WAN INTERFACE ...................................................................................................... 315 13.7 SDRAM TIMING...................................................................................................................... 316 13.8 MICROPROCESSOR BUS AC CHARACTERISTICS ........................................................................ 318 13.9 AC CHARACTERISTICS: RECEIVE-SIDE ..................................................................................... 321 13.10 AC CHARACTERISTICS: BACKPLANE CLOCK TIMING .................................................................. 325 13.11 AC CHARACTERISTICS: TRANSMIT SIDE ................................................................................... 326 13.12 JTAG INTERFACE TIMING ........................................................................................................ 329 14 JTAG INFORMATION ................................................................................................................ 330 14.1 JTAG TAP CONTROLLER STATE MACHINE DESCRIPTION.......................................................... 331 14.2 INSTRUCTION REGISTER .......................................................................................................... 333 14.3 JTAG ID CODES..................................................................................................................... 335 14.4 TEST REGISTERS .................................................................................................................... 335
14.4.1 Boundary Scan Register ...................................................................................................................335 14.4.2 Bypass Register ................................................................................................................................335 14.4.3 Identification Register........................................................................................................................335
14.5 JTAG FUNCTIONAL TIMING...................................................................................................... 336 15 PACKAGE INFORMATION ........................................................................................................ 337 15.1 PACKAGE OUTLINE DRAWING OF 256-BGA (VIEW FROM BOTTOM OF DEVICE) ........................... 337 16 REVISION HISTORY.................................................................................................................. 338
5 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
LIST OF FIGURES
Figure 3-1. Ethernet-to-WAN Extension (With or Without Framing) ......................................................................... 17 Figure 6-1. Main Block Diagram ................................................................................................................................ 20 Figure 6-2. Block Diagram of T1/E1/J1 Transceiver.................................................................................................. 21 Figure 6-3. Receive and Transmit T1/E1/J1 LIU ....................................................................................................... 22 Figure 6-4. Receive and Transmit T1/E1/J1 Framer ................................................................................................. 23 Figure 6-5. T1/E1/J1 Backplane Interface ................................................................................................................. 24 Figure 7-1. 256-Ball BGA Pinout................................................................................................................................ 40 Figure 9-1. Clocking for the DS33R11 ....................................................................................................................... 44 Figure 9-2. Device Interrupt Information Flow Diagram ............................................................................................. 49 Figure 9-3. Flow Control Using Pause Control Frame ............................................................................................... 55 Figure 9-4. IEEE 802.3 Ethernet Frame .................................................................................................................... 56 Figure 9-5. Configured as DTE Connected to an Ethernet PHY in MII Mode............................................................ 58 Figure 9-6. DS33R11 Configured as a DCE in MII Mode .......................................................................................... 59 Figure 9-7. RMII Interface .......................................................................................................................................... 61 Figure 9-8. MII Management Frame .......................................................................................................................... 62 Figure 9-9. PRBS Synchronization State Diagram .................................................................................................... 63 Figure 9-10. Repetitive Pattern Synchronization State Diagram................................................................................ 64 Figure 9-11. HDLC Encapsulation of MAC Frame..................................................................................................... 67 Figure 9-12. LAPS Encoding of MAC Frames Concept............................................................................................. 68 Figure 9-13. X.86 Encapsulation of the MAC frame .................................................................................................. 69 Figure 10-1. T1/E1/J1 Clock Map .............................................................................................................................. 72 Figure 10-2. Simplified Diagram of Receive Signaling Path ...................................................................................... 82 Figure 10-3. Simplified Diagram of Transmit Signaling Path ..................................................................................... 84 Figure 10-4. CRC-4 Recalculate Method................................................................................................................... 90 Figure 10-5. Typical Monitor Application.................................................................................................................. 101 Figure 10-6. CMI Coding.......................................................................................................................................... 103 Figure 10-7. Basic Interface..................................................................................................................................... 104 Figure 10-8. E1 Transmit Pulse Template ............................................................................................................... 105 Figure 10-9. T1 Transmit Pulse Template ............................................................................................................... 105 Figure 10-10. Jitter Tolerance.................................................................................................................................. 106 Figure 10-11. Jitter Tolerance (E1 Mode) ................................................................................................................ 106 Figure 10-12. Jitter Attenuation (T1 Mode) .............................................................................................................. 107 Figure 10-13. Jitter Attenuation (E1 Mode) .............................................................................................................. 107 Figure 10-14. Optional Crystal Connections ............................................................................................................ 108 Figure 10-15. Simplified Diagram of BERT in Network Direction ............................................................................ 109 Figure 10-16. Simplified Diagram of BERT in Backplane Direction......................................................................... 109 Figure 10-17. T1/J1 Transmit Flow Diagram ........................................................................................................... 113 Figure 10-18. E1 Transmit Flow Diagram ................................................................................................................ 115 Figure 12-1. Tx Serial Interface Functional Timing.................................................................................................. 294 Figure 12-2. Rx Serial Interface Functional Timing ................................................................................................. 294 Figure 12-3. Transmit Byte Sync Functional Timing ................................................................................................ 295 Figure 12-4. Receive Byte Sync Functional Timing ................................................................................................. 295 Figure 12-5. MII Transmit Functional Timing ........................................................................................................... 295 Figure 12-6. MII Transmit Half Duplex with a Collision Functional Timing .............................................................. 296 Figure 12-7. MII Receive Functional Timing ............................................................................................................ 296 Figure 12-8. RMII Transmit Interface Functional Timing ......................................................................................... 296 Figure 12-9. RMII Receive Interface Functional Timing .......................................................................................... 297 Figure 12-10. Receive-Side D4 Timing.................................................................................................................... 297 Figure 12-11. Receive-Side ESF Timing ................................................................................................................. 297 Figure 12-12. Receive-Side Boundary Timing (Elastic Store Disabled) .................................................................. 298 Figure 12-13. Receive-Side 1.544MHz Boundary Timing (Elastic Store Enabled) .................................................. 298 Figure 12-14. Receive-Side 2.048MHz Boundary Timing (Elastic Store Enabled) .................................................. 299 Figure 12-15. Transmit-Side D4 Timing................................................................................................................... 299 Figure 12-16. Transmit-Side ESF Timing ................................................................................................................ 300 Figure 12-17. Transmit-Side Boundary Timing (with Elastic Store Disabled) .......................................................... 300 Figure 12-18. Transmit-Side 1.544MHz Boundary Timing (Elastic Store Enabled)................................................. 301 6 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Figure 12-19. Transmit-Side 2.048MHz Boundary Timing (Elastic Store Enabled)................................................. 301 Figure 12-20. Receive-Side Timing ......................................................................................................................... 302 Figure 12-21. Receive-Side Boundary Timing (with Elastic Store Disabled) ........................................................... 302 Figure 12-22. Receive-Side Boundary Timing, RSYSCLK = 1.544MHz (E-Store Enabled) .................................... 303 Figure 12-23. Receive-Side Boundary Timing, RSYSCLK = 2.048MHz (E-Store Enabled) .................................... 303 Figure 12-24. G.802 Timing, E1 Mode Only ............................................................................................................ 304 Figure 12-25. Transmit-Side Timing ........................................................................................................................ 304 Figure 12-26. Transmit-Side Boundary Timing (Elastic Store Disabled) ................................................................. 305 Figure 12-27. Transmit-Side Boundary Timing, TSYSCLK = 1.544MHz (Elastic Store Enabled) .......................... 305 Figure 12-28. Transmit-Side Boundary Timing, TSYSCLK = 2.048MHz (Elastic Store Enabled) ........................... 306 Figure 13-1. Transmit MII Interface Timing.............................................................................................................. 309 Figure 13-2. Receive MII Interface Timing............................................................................................................... 310 Figure 13-3. Transmit RMII Interface Timing ........................................................................................................... 311 Figure 13-4. Receive RMII Interface Timing ............................................................................................................ 312 Figure 13-5. MDIO Interface Timing ........................................................................................................................ 313 Figure 13-6. Transmit WAN Interface Timing .......................................................................................................... 314 Figure 13-7. Receive WAN Interface Timing ........................................................................................................... 315 Figure 13-8. SDRAM Interface Timing..................................................................................................................... 317 Figure 13-9. Intel Bus Read Timing (MODEC = 00) ................................................................................................ 319 Figure 13-10. Intel Bus Write Timing (MODEC = 00) .............................................................................................. 319 Figure 13-11. Motorola Bus Read Timing (MODEC = 01) ....................................................................................... 320 Figure 13-12. Motorola Bus Write Timing (MODEC = 01) ....................................................................................... 320 Figure 13-13. Receive-Side Timing ......................................................................................................................... 322 Figure 13-14. Receive-Side Timing, Elastic Store Enabled ..................................................................................... 323 Figure 13-15. Receive Line Interface Timing ........................................................................................................... 324 Figure 13-16. Receive Timing Delay RCLKO to BPCLK ......................................................................................... 325 Figure 13-17. Transmit-Side Timing ........................................................................................................................ 327 Figure 13-18. Transmit-Side Timing, Elastic Store Enabled.................................................................................... 328 Figure 13-19. Transmit Line Interface Timing.......................................................................................................... 328 Figure 13-20. JTAG Interface Timing Diagram........................................................................................................ 329 Figure 14-1. JTAG Functional Block Diagram ......................................................................................................... 330 Figure 14-2. TAP Controller State Diagram ............................................................................................................. 333 Figure 14-3. JTAG Functional Timing...................................................................................................................... 336
7 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
LIST OF TABLES
Table 2-1. T1-Related Telecommunications Specifications ...................................................................................... 16 Table 7-1. Detailed Pin Descriptions.......................................................................................................................... 25 Table 9-1. Clocking Options for the Ethernet Interface.............................................................................................. 43 Table 9-2. Reset Functions........................................................................................................................................ 46 Table 9-3. Registers Related to Connections and Queues........................................................................................ 52 Table 9-4. Options for Flow Control ........................................................................................................................... 53 Table 9-5. Registers Related to Setting the Ethernet Port......................................................................................... 57 Table 9-6. MAC Control Registers ............................................................................................................................. 60 Table 9-7. MAC Status Registers .............................................................................................................................. 60 Table 10-1. T1/E1/J1 Transmit Clock Source............................................................................................................ 73 Table 10-2. T1 Alarm Criteria..................................................................................................................................... 75 Table 10-3. E1 Sync/Resync Criteria ......................................................................................................................... 76 Table 10-4. E1 Alarm Criteria .................................................................................................................................... 77 Table 10-5 T1 Line Code Violation Counting Options................................................................................................ 78 Table 10-6. E1 Line-Code Violation Counting Options .............................................................................................. 78 Table 10-7. T1 Path Code Violation Counting Arrangements.................................................................................... 79 Table 10-8. T1 Frames Out-of-Sync Counting Arrangements ................................................................................... 80 Table 10-9. Time Slot Numbering Schemes.............................................................................................................. 85 Table 10-10. Idle-Code Array Address Mapping........................................................................................................ 86 Table 10-11. Elastic Store Delay After Initialization ................................................................................................... 89 Table 10-12. HDLC Controller Registers ................................................................................................................... 94 Table 10-13. Transformer Specifications................................................................................................................. 104 Table 10-14. Transmit Error-Insertion Setup Sequence .......................................................................................... 111 Table 10-15. Error Insertion Examples .................................................................................................................... 111 Table 11-1. Register Address Map .......................................................................................................................... 117 Table 11-2. Global Ethernet Mapper Register Bit Map ............................................................................................ 118 Table 11-3. Arbiter Register Bit Map........................................................................................................................ 119 Table 11-4. BERT Register Bit Map......................................................................................................................... 119 Table 11-5. Serial Interface Register Bit Map .......................................................................................................... 120 Table 11-6. Ethernet Interface Register Bit Map...................................................................................................... 122 Table 11-7. MAC Indirect Register Bit Map ............................................................................................................. 123 Table 11-8. T1/E1/J1 Transceiver Register Bit Map (Active when CST = 0) ........................................................... 125 Table 13-1. Recommended DC Operating Conditions ............................................................................................ 307 Table 13-2. DC Electrical Characteristics ................................................................................................................ 307 Table 13-3. Thermal Characteristics........................................................................................................................ 308 Table 13-4. Theta-JA vs. Airflow.............................................................................................................................. 308 Table 13-5. Transmit MII Interface........................................................................................................................... 309 Table 13-6. Receive MII Interface............................................................................................................................ 310 Table 13-7. Transmit RMII Interface ........................................................................................................................ 311 Table 13-8. Receive RMII Interface ......................................................................................................................... 312 Table 13-9. MDIO Interface ..................................................................................................................................... 313 Table 13-10. Transmit WAN Interface ..................................................................................................................... 314 Table 13-11. Receive WAN Interface ...................................................................................................................... 315 Table 13-12. SDRAM Interface Timing.................................................................................................................... 316 Table 13-13. AC Characteristics--Microprocessor Bus Timing .............................................................................. 318 Table 13-14. AC Characteristics: Receive Side....................................................................................................... 321 Table 13-15. AC Characteristics: Backplane Clock Synthesis ................................................................................ 325 Table 13-16. AC Characteristics: Transmit Side...................................................................................................... 326 Table 13-17. JTAG Interface Timing........................................................................................................................ 329 Table 14-1. Instruction Codes for IEEE 1149.1 Architecture ................................................................................... 334 Table 14-2. ID Code Structure ................................................................................................................................. 335
8 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
1 DESCRIPTION
The DS33R11 provides interconnection and mapping functionality between Ethernet Packet Systems and T1/E1/J1 WAN Time-Division Multiplexed (TDM) systems. The device is composed of a 10/100 Ethernet MAC, Packet Arbiter, Committed Information Rate Controller (CIR), HDLC/X.86 (LAPS) Mapper, SDRAM interface, control ports, Bit Error Rate Tester (BERT), and integrated T1/E1/J1 Transceiver. The packet interface consists of a MII/RMII Ethernet PHY interface. The Ethernet interface can be configured for 10Mbit/s or 100Mbit/s service. The DS33R11 encapsulates Ethernet traffic with HDLC or X.86 (LAPS) encoding to be transmitted over a T1, E1, or J1 line. The T1/E1/J1 interface also receives encapsulated Ethernet packets and transmits the extracted packets over the Ethernet ports. Access is provided to the signals between the Serial port and the integrated T1/E1/J1 Transceiver. The device includes a software-selectable T1, E1, or J1 single-chip transceiver (SCT) for short-haul and long-haul applications. The transceiver is composed of an LIU, framer, and two additional HDLC controllers. The transceiver is software compatible with the DS2155 and DS2156. The LIU is composed of transmit and receive interfaces and a jitter attenuator. The transmit interface is responsible for generating the necessary waveshapes for driving the network and providing the correct source impedance depending on the type of media used. T1 waveform generation includes DSX-1 line build-outs as well as CSU line build-outs of -7.5dB, -15dB, and -22.5dB. E1 waveform generation includes G.703 waveshapes for both 75W coax and 120W twisted cables. The receive interface provides network termination and recovers clock and data from the network. The receive sensitivity adjusts automatically to the incoming signal and can be programmed for 0 to 43dB or 0 to 12dB for E1 applications and 0 to 30dB or 0 to 36dB for T1 applications. The jitter attenuator removes phase jitter from the transmitted or received signal. The crystal-less jitter attenuator requires only a 2.048MHz MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK in T1 applications) and can be placed in either transmit or receive data paths. An additional feature of the LIU is a CMI coder/decoder for interfacing to optical networks. On the transmit side, clock, data, and frame-sync signals are provided to the framer by the backplane interface section. The framer inserts the appropriate synchronization framing patterns, alarm information, calculates and inserts the CRC codes, and provides the B8ZS/HDB3 (zero code suppression) and AMI line coding. The receiveside framer decodes AMI, B8ZS, and HDB3 line coding, synchronizes to the data stream, reports alarm information, counts framing/coding/CRC errors, and provides clock/data and frame-sync signals to the backplane interface section. Diagnostic capabilities include loopbacks, PRBS pattern generation/detection, and 16-bit loop-up and loopdown code generation and detection. Both the transmit and receive path have two HDLC controllers. The HDLC controllers transmit and receive data through the framer block. The HDLC controllers can be assigned to any time slot, group of time slots, portion of a time slot or to FDL (T1) or Sa bits (E1). Each controller has 128-byte FIFOs, thus reducing the amount of processor overhead required to manage the flow of data. In addition, built-in support for reducing the processor time is required in SS7 applications. The backplane interface provides a versatile method of sending and receiving data from the host system. Elastic stores provide a method for interfacing to asynchronous systems, converting from a T1/E1 network to a 2.048MHz, 4.096MHz, 8.192MHz, or N x 64kHz system backplane. The elastic stores also manage slip conditions (asynchronous interface). An 8-bit parallel microcontroller port provides access for control and configuration of all the features of the device. The internal 100MHz SDRAM controller interfaces to a 32-bit wide 128Mb SDRAM. The SDRAM is used to buffer the data from the Ethernet and WAN ports for transport. The external SDRAM can accommodate up to 8192 frames with a maximum frame size of 2016 bytes. Diagnostic capabilities include SDRAM BIST, loopbacks, PRBS pattern generation/detection, and 16-bit loop-up and loop-down code generation and detection. The DS33R11 operates with a 1.8V core supply and 3.3V I/O supply.
9 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver The integrated Ethernet Mapper is software compatible with the DS33Z11 Ethernet mapper. There are a few things to note when porting a DS33Z11 application to this device: * * * * * The SPI and hardware modes are not supported. RSER has been renamed to RSERI. RCLK has been renamed to RCLKI. TSER has been renamed to TSERO. TCLK has been renamed to TCLKE.
The integrated T1/E1/J1 transceiver is software compatible with the DS2155 T1/E1/J1 transceiver. There are a few things to note when porting a DS2155 application to this device: * * * * * * * * * * The Facilities Data Link (FDL) support is available through software only. The TLINK, RLINK, TLCLK, RLCLK pins are not available on the DS33R11. Multiplexed Microprocessor Bus mode is not supported on the DS33R11. The Extended System Information Bus (ESIB) is not supported on the DS33R11. The MODEC pins serve the function of the DS2155's BTS pin. The interim LIU/Framer clock signals RCLKI, RCLKO have been renamed to RDCLKI, RDCLKO to avoid confusion with the receive clock connections between the transceiver and the Ethernet mapper. The interim LIU/Framer clock signals TCLKI, TCLKO have been renamed to TDCLKI, TDCLKO to avoid confusion with the receive clock connections between the transceiver and the Ethernet mapper. RSER has been renamed RSERO. RCLK has been renamed RCLKO. TSER has been renamed TSERI. TCLK has been renamed TCLKT.
10 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2
2.1
FEATURE HIGHLIGHTS
General
* * * * * * * 256-pin, 27mm BGA package 1.8V and 3.3V supplies IEEE 1149.1 JTAG boundary scan Software access to device ID and silicon revision Development support includes evaluation kit, driver source code, and reference designs Reference design routes on a two-layer PC board Programmable output clocks for fractional T1, E1, H0, and H12 applications
2.2
Microprocessor Interface
* * * * * * Parallel control port with 8-bit data bus Nonmultiplexed Intel and Motorola timing modes Internal software reset and external hardware reset-input pin Supports polled or interrupt-driven environments Software access to device ID and silicon revision Global interrupt-output pin
2.3
HDLC Ethernet Mapping
* * * * * * * * * * Dedicated HDLC controller engine for protocol encapsulation Compatible with polled or interrupt driven environments Programmable FCS insertion and extraction Programmable FCS type Supports FCS error insertion Programmable packet size limits (Minimum 64 bytes and maximum 2016 bytes) Supports bit stuffing/destuffing 43 Selectable packet scrambling/descrambling (X +1) Separate FCS errored packet and aborted packet counts Programmable inter-frame fill for transmit HDLC
2.4
X.86 (Link Access Protocol for SONET/SDH) Ethernet Mapping
* * * * * * * * * * * Programmable X.86 address/control fields for transmit and receive Programmable 2-byte protocol (SAPI) field for transmit and receive 32 bit FCS Transmit transparency processing--7E is replaced by 7D, 5E Transmit transparency processing--7D replaced by 7D, 5D Receive rate adaptation (7D, DD) is deleted. Receive transparency processing--7D, 5E is replaced by 7E Receive transparency processing--7D, 5D is replaced by 7D Receive abort sequence the LAPS packet is dropped if 7D7E is detect 43 Self-synchronizing X +1 payload scrambling. Frame indication due to bad address/control/SAPI, FCS error, abort sequence or frame size longer than preset max
11 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.5
Additional HDLC Controllers in the Integrated T1/E1/J1 Transceiver
* * * * * * * * Two additional independent HDLC controllers Fast load and unload features for FIFOs SS7 support for FISU transmit and receive Independent 128-byte Rx and Tx buffers with interrupt support Access FDL, Sa, or single/multiple DS0 channels DS0 access includes Nx64 or Nx56 Compatible with polled or interrupt driven environments Bit-oriented code (BOC) support
2.6
Committed Information Rate (CIR) Controller
* * * CIR Rate controller limits transmission of data from the Ethernet interface to the serial interface CIR granularity at 512kbit/s CIR averaging for smoothing traffic peaks
2.7
SDRAM Interface
* * * * * * Interface for 128Mb, 32-bit-wide SDRAM SDRAM Interface speed up to 100MHz Auto refresh timing Automatic precharge Master clock provided to the SDRAM No external components required for SDRAM connectivity
2.8
MAC Interface
* * * * * * * * * * * * MAC port with standard MII (less TX_ER) or RMII 10Mbps and 100Mbps Data rates Configurable DTE or DCE modes Facilitates auto-negotiation by host microprocessor Programmable half and full-duplex modes Flow control for both half-duplex (back-pressure) and full-duplex (PAUSE) modes Programmable Maximum MAC frame size up to 2016 bytes Minimum MAC frame size: 64 bytes Discards frames greater than programmed maximum MAC frame size and runt, nonoctet bounded, or bad-FCS frames upon reception Configurable for promiscuous broadcast-discard mode. Programmable threshold for SDRAM queues to initiate flow control and status indication MAC loopback support for transmit data looped to receive data at the MII/RMII interface
12 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.9
T1/E1/J1 Line Interface
* * * * * * * * * * * * * * * * * * * * * * * Requires only a 2.048MHz master clock for both E1 and T1 operation with the option to use 1.544MHz for T1 operation Fully software configurable Short-haul and long-haul applications Automatic receive sensitivity adjustments Ranges include 0 to 43dB or 0 to 12dB for E1 applications and 0 to 13dB or 0 to 36dB for T1 applications Receive level indication in 2.5dB steps from -42.5dB to -2.5dB Internal receive termination option for 75W, 100W, and 120W lines Internal transmit termination option for 75W, 100W, and 120W lines Monitor application gain settings of 20dB, 26dB, and 32dB G.703 receive synchronization-signal mode Flexible transmit waveform generation T1 DSX-1 line build-outs T1 CSU line build-outs of -7.5dB, -15dB, and -22.5dB E1 waveforms include G.703 waveshapes for both 75W coax and 120W twisted cables AIS generation independent of loopbacks Alternating ones and zeros generation Square-wave output Open-drain output option NRZ format option Transmitter power-down Transmitter 50mA short-circuit limiter with current-limit-exceeded indication Transmit open-circuit-detected indication Line interface function can be completely decoupled from the framer/formatter
2.10 Clock Synthesizer
* * Output frequencies include 2.048MHz, 4.096MHz, 8.192MHz, and 16.384MHz Derived from recovered receive clock
2.11 Jitter Attenuator
* * * * 32-bit or 128-bit crystal-less jitter attenuator Requires only a 2.048MHz master clock for both E1 and T1 operation with the option to use 1.544MHz for T1 operation Can be placed in either the receive or transmit path or disabled Limit trip indication
13 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.12 T1/E1/J1 Framer
* * * * * * * * * * * * * * * * Fully independent transmit and receive functionality Full receive and transmit path transparency T1 framing formats include D4 (SLC-96) and ESF Detailed alarm and status reporting with optional interrupt support Large path and line error counters for: o T1: BPV, CV, CRC6, and framing bit errors o E1: BPV, CV, CRC4, E-bit, and frame alignment errors Timed or manual update modes DS1 idle code generation on a per-channel basis in both transmit and receive paths o User-defined o Digital milliwatt ANSI T1.403-1998 Support RAI-CI detection and generation AIS-CI detection and generation E1ETS 300 011 RAI generation G.965 V5.2 link detect Ability to monitor one DS0 channel in both the transmit and receive paths In-band repeating pattern generators and detectors o Three independent generators and detectors o Patterns from 1 to 8 bits or 16 bits in length RCL, RLOS, RRA, and RAIS alarms interrupt on change-of-state Flexible signaling support o Software or hardware based o Interrupt generated on change of signaling data o Receive signaling freeze on loss-of-sync, carrier loss, or frame slip Addition of hardware pins to indicate carrier loss and signaling freeze Automatic RAI generation to ETS 300 011 specifications Access to Sa and Si bits Option to extend carrier loss criteria to a 1ms period as per ETS 300 233 Japanese J1 support o Ability to calculate and check CRC6 according to the Japanese standard
* * * *
*
o
Ability to generate Yellow Alarm according to the Japanese standard
2.13 TDM Bus
* Dual two-frame independent receive and transmit elastic stores o Independent control and clocking o Controlled slip capability with status o Minimum delay mode supported Programmable output clocks for fractional T1, E1, H0, and H12 applications Hardware signaling capability o Receive signaling reinsertion to a backplane multiframe sync o Availability of signaling in a separate PCM data stream o Signaling freezing Ability to pass the T1 F-bit position through the elastic stores in the 2.048MHz backplane mode Access to the data streams in between the framer/formatter and the elastic stores User-selectable synthesized clock output
* *
* * *
14 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.14 Test and Diagnostics
* * * * * * * * * * * * * IEEE 1149.1 support Programmable on-chip bit error-rate tester (BERT) Pseudorandom patterns including QRSS User-defined repetitive patterns Daly pattern Error insertion single and continuous Total bit and errored bit counts Payload error insertion Error insertion in the payload portion of the T1 frame in the transmit path Errors can be inserted over the entire frame or selected channels Insertion options include continuous and absolute number with selectable insertion rates F-bit corruption for line testing Loopbacks: remote, local, analog, and per-channel loopback
15 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.15 Specifications Compliance
The DS33R11 meets relevant telecommunications specifications. The following table provides the specifications and relevant sections that are applicable to the DS33R11.
Table 2-1. T1-Related Telecommunications Specifications
IEEE 802.3-2002--CSMA/CD access method and physical layer specifications. RFC1662--PPP in HDLC-like Framing RFC2615--PPP over SONET/SDH X.86--Ethernet over LAPS RMII--Industry Implementation Agreement for "Reduced MII Interface," Sept 1997 ANSI: T1.403-1995, T1.231-1993, T1.408 AT&T: TR54016, TR62411 ITU-T: G.703, G.704, G.706, G.736, G.775, G.823, G.932, I.431, O.151, Q.161, Recommendation I.432-03/93 B-ISDN User-Network Interface--Physical Layer Specification ETSI: ETS 300 011, ETS 300 166, ETS 300 233, CTR12, CTR4 Japanese: JTG.703, JTI.431, JJ-20.11 (CMI Coding Only)
16 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
3 APPLICATIONS
The DS33R11 is ideal for application areas such as transparent LAN service, LAN extension, and Ethernet delivery over T1/E1/J1, T3/E3, OC-1/EC-1, G.SHDSL, or HDSL2/4. For an example of a complete LAN-to-WAN design, refer to Application Note 3411: DS33Z11--Ethernet LAN to Unframed T1/E1 WAN Bridge, available on our website at www.maxim-ic.com/telecom.
Figure 3-1. Ethernet-to-WAN Extension (With or Without Framing)
T1/E1/J1 Stream Inter-Building LAN Extension
RMII, MII 10 Base T 100 Base T DS33R11 Ethernet
Clock Sources SDRAM
17 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
4 ACRONYMS AND GLOSSARY
* * * * * * * * * BERT: Bit Error-Rate Tester DCE: Data Communication Interface DTE: Data Terminating Interface FCS: Frame Check Sequence HDLC: High-Level Data Link Control MAC: Media Access Control MII: Media Independent Interface RMII: Reduced Media Independent Interface WAN: Wide Area Network
Note 1: Previous versions of this document used the term "Subscriber" to refer to the Ethernet Interface function. The register names have been allowed to remain with a "SU." prefix to avoid register renaming. Note 2: Previous versions of this document used the term "Line" to refer to the Serial Interface. The register names have been allowed to remain with a "LI." prefix to avoid register renaming. Note3 : The terms "Transmit Queue" and "Receive Queue" are with respect to the Ethernet Interface. The Receive Queue is the queue for the data that arrives on the MII/RMII interface, is processed by the MAC and stored in the SDRAM. Transmit queue is for data that arrives from the Serial port, is processed by the HDLC and stored in the SDRAM to be sent to the MAC transmitter. Note 4: This data sheet assumes a particular nomenclature of the T1 operating environment. In each 125ms frame there are 24 8-bit channels plus a framing bit. It is assumed that the framing bit is sent first followed by channel 1. Each channel is made up of eight bits that are numbered 1 to 8. Bit number 1 is the MSB and is transmitted first. Bit number 8 is the LSB and is transmitted last. The term "locked" is used to refer to two clock signals that are phaseor frequency-locked or derived from a common clock (i.e., a 1.544MHz clock can be locked to a 2.048MHz clock if they share the same 8kHz component). Throughout this data sheet, the following abbreviations are used: B8ZS BOC CRC D4 ESF FDL FPS Fs Ft HDLC MF SLC-96 Bipolar with 8 Zero Substitution Bit-Oriented Code Cyclical Redundancy Check Superframe (12 frames per multiframe) Multiframe Structure Extended Superframe (24 frames per multiframe) Multiframe Structure Facility Data Link Framing Pattern Sequence in ESF Signaling Framing Pattern in D4 Terminal Framing Pattern in D4 High-Level Data Link Control Multiframe Subscriber Loop Carrier--96 Channels
18 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
5 MAJOR OPERATING MODES
Microprocessor control is possible through the 8-bit parallel control port and provides configuration for all the features of the device. The Ethernet Link Transport Engine in the device can be configured for HDLC or X.86 encapsulation. The integrated transceiver can be software configured for T1, E1, or J1 operation. It is composed of a line interface unit (LIU), framer, two additional HDLC controllers, and a TDM backplane interface, and is controlled via an 8-bit parallel port configured for Intel or Motorola bus operations. The LIUs are composed of a transmit interface, receive interface, and a jitter attenuator. The transmit interface is responsible for generating the necessary waveshapes for driving the network and providing the correct source impedance depending on the type of media used. T1 waveform generation includes DSX-1 line build-outs as well as CSU line build-outs of -7.5dB, -15dB, and -22.5dB. E1 waveform generation includes G.703 waveshapes for both 75W coax and 120W twisted cables. The receive interface provides network termination and recovers clock and data from the network. The receive sensitivity adjusts automatically to the incoming signal and can be programmed for 0dB to 43dB or 0dB to 12dB for E1 applications and 0dB to 15dB or 0dB to 36dB for T1 applications. The jitter attenuator removes phase jitter from the transmitted or received signal. The crystal-less jitter attenuator requires only a 2.048MHz MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK in T1 applications) and can be placed in either transmit or receive data paths. More information on microprocessor control is available in Section 8.1.
19 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
6 BLOCK DIAGRAMS
Figure 6-1. Main Block Diagram
TDCLKI TDCLKO TPOSI TPOSO TNEGI TNEGO TCHBLK TCHCLK TCLKT TSERI TSERO TCLKE TDEN
CST CS A0-A9 D0-D7 WR RD INT
MCLK
mP Port CLAD TRANSMIT SERIAL PORT CIR CONTROLLER TRANSMIT FRAMER TRANSMIT LIU PACKET HDLC/X.86 CLAD SYSCLKI
(RMII MODE)
TTIP TRING
MUX
T1/E1/J1 TRANSCEIVER
HDLC
ETHERNET MAC JTAG1 JTAG Pins
RXD[0:1] RX_CLK CRS_DV RX_ERR REF_CLK REF_CLKO
ETHERNET MAPPER
BERT
HDLC
BERT
ARBITER
RECEIVE LIU
RECEIVIE FRAMER
RRING
RECEIVE SERIAL PORT
MUX
PACKET HDLC/X.86
RTIP
TX_EN TXD[0:1] MDC MDIO
JTAG2
SDRAM PORT LIUC RDCLKI RDCLKO RPOSI RPOSO RNEGI RNEGO RCHBLK RCHCLK RCLKO RSERO JTAG Pins RSERI RCLKI RDEN
SDCS SRAS SCAS SWE SBA[0:1] SDATA[0:32] SDMASK[0:4] SDCLK
NOTE: SOME PINS NOT SHOWN. THE BLOCK IN THE DIAGRAM LABELED "T1/E1/J1 TRANSCEIVER" IS DIVIDED INTO THREE FUNCTIONAL BLOCKS: LIU, FRAMER, AND BACKPLANE INTERFACE OUTLINED IN THE FOLLOWING DIAGRAMS.
20 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-2. Block Diagram of T1/E1/J1 Transceiver
CLOCK
CLOCK ADAPTER
EXTERNAL ACCESS TO RECEIVE SIGNALS
REMOTE LOOPBACK
JITTER ATTENUATOR
LOCAL LOOPBACK
FRAMER LOOPBACK
TX LIU
MUX
FRAMER SINGALING ALARM GEN HDLCs CRC GEN HDB3 / B8ZS
BACKPLANE INTERFACE CIRCUIT
LIU
EXTERNAL ACCESS TO TRANSMIT SIGNALS
FRAMER
ESIB
BACKPLANE INTERFACE
JTAG
HOST INTERFACE
21 of 338
BACKPLANE
RX LIU T1/E1/J1 NETWORK
MUX
PAYLOAD LOOPBACK
HDB3 / B8ZS SYNC SINGALING ALARM DET HDLCs
BACKPLANE CLOCK SYNTH
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-3. Receive and Transmit T1/E1/J1 LIU
RDCLKI
RPOSO
RDCLKO
RNEGI
RNEGO
XTALD
RPOSI
8XCLK
32.768MHz
MCLK RECEIVE LINE I/F
RCL
VCO / PLL
MUX JACLK REMOTE LOOPBACK RPOS RCLK RNEG
JITTER ATTENUATOR TRANSMIT OR RECEIVE PATH
RRING RTIP
LOCAL LOOPBACK
TRANSMIT LINE I/F
TRING TTIP
TNEG TCLK TPOS INTERNAL SIGNALS TO FRAMER
MUX
TNEGO
TPOSO
TNEGI
TPOSI
TDCLKI
TDCLKO
LIUC
22 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-4. Receive and Transmit T1/E1/J1 Framer
REC HDLC #1 128 Byte FIFO DATA MAPPER
REC HDLC #2 128 Byte FIFO MAPPER
RPOS RNEG RCLK
DATA
PAYLOAD LOOPBACK
RECEIVE FRAMER
CLOCK SYNC SYNC
CLOCK SYNC SYNC CLOCK DATA INTERNAL SIGNALS TO BACKPLANE INTERFACE
FRAMER LOOPBACK
TPOS TNEG TCLK INTERNAL SIGNALS FROM LIU
TRANSMIT FRAMER
CLOCK DATA
MAPPER
MAPPER
XMIT HDLC #1 128 Byte FIFO
XMIT HDLC #2 128 Byte FIFO
23 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-5. T1/E1/J1 Backplane Interface
Sa BIT/FDL EXTRACTION
RLINK RLCLK RSIG RSIGFR
SIGNALING BUFFER
DATA CLOCK SYNC INTERNAL SIGNALS FROM FRAMER
ELASTIC STORE
RSYSCLK RSERO RCLKO RSYNC RMSYNC RFSYNC RDATA
CHANNEL TIMING
RCHCLK RCHBLK
SYNC DATA CLOCK Sa/FDL INSERT ELASTIC STORE
SIGNALING BUFFER
TSERI TSIG TSSYNC TSYSCLK TSYNC
TESO TDATA TLCLK TLINK CHANNEL TIMING TCLK MUX TCHCLK TCHBLK TCLKT
JACLK
24 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
7 PIN DESCRIPTIONS
7.1 Pin Functional Description
Note that all digital pins are IO pins in JTAG mode. This feature increases the effectiveness of board level ATPG patterns.
LEGEND: I = input, O = output, Ipu = input with pullup, Oz = output with tri-state, IO = bidirectional pin, IOz = bidirectional pin with tri-state.
Table 7-1. Detailed Pin Descriptions
NAME PIN TYPE MICROPROCESSOR PORT A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 D0 D1 D2 D3 D4 D5 D6 D7 A18 B18 C18 A17 B17 C17 A16 B16 C16 C15 A14 B14 C14 A13 B13 C13 A12 B12 I I I I I I I I I I IOZ IOZ IOZ IOZ IOZ IOZ IOZ IOZ Address Bit 0: Address bit 0 of the microprocessor interface. Least Significant Bit. Address Bit 1: Address bit 1 of the microprocessor interface. Address Bit 2: Address bit 2 of the microprocessor interface. Address Bit 3: Address bit 3 of the microprocessor interface. Address Bit 4: Address bit 4 of the microprocessor interface. Address Bit 5: Address bit 5 of the microprocessor interface. Address Bit 6: Address bit 6 of the microprocessor interface. Address Bit 7: Address bit 7 of the microprocessor interface. Address Bit 8: Address bit 8 of the microprocessor interface. Address Bit 9: Address bit 9 of the microprocessor interface. Data Bit 0: Bidirectional data bit 0 of the microprocessor interface. Least Significant Bit. Not driven when CS =1 or RST =0. Data Bit 1: Bidirectional data bit 1 of the microprocessor interface. Not driven when CS =1 or RST =0. Data Bit 2: Bidirectional data bit 2 of the microprocessor interface. Not driven when CS =1 or RST=0. Data Bit 3: Bidirectional data bit 3 of the microprocessor interface. Not driven when CS =1 or RST=0. Data Bit 4: Bidirectional data bit 4 of the microprocessor interface. Not driven when CS =1 or RST=0. Data Bit 5: Bidirectional data bit 5 of the microprocessor interface. Not driven when CS =1 or RST=0. Data Bit 6: Bidirectional data bit 6 of the microprocessor interface. Not driven when CS =1 or RST=0. Data Bit 7: Bidirectional data bit 7 of the microprocessor interface. Most Significant Bit. Not driven when CS =1 or RST=0. Write (Intel Mode): The DS33R11 captures the contents of the data bus (D0-D7) on the rising edge of WR and writes them to the addressed register location. CS must be held low during write operations. Read Write (Motorola Mode): Used to indicate read or write operation. RW must be set high for a register read cycle and low for a register write cycle. DESCRIPTION
WR/RW
C11
I
25 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE DESCRIPTION Read Data Strobe (Intel Mode): The DS33R11 drives the data bus (D0-D7) with the contents of the addressed register while RD and CS are both low. Data Strobe (Motorola Mode): Used to latch data through the microprocessor interface. DS must be low during read and write operations. Chip Select for Protocol Conversion Device: This pin must be taken low for read/write operations. When CS is high, the RD/DS and WR signals are ignored. Chip Select for the T1/E1/J1 Transceiver: Must be low to read or write the T1/E1/J1 transceiver. Interrupt Output: Outputs a logic zero when an unmasked interrupt event is detected. INT is deasserted when all interrupts have been acknowledged and serviced. Active low. Inactive state is programmable in register GL.CR1. is deasserted when all interrupts have been acknowledged and serviced. Active low. Inactive state is programmable in register GL.CR1.
RD/DS
B11
I
CS CST
A11 D7
I I
INT
A10
OZ
26 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE MII/RMII PHY PORT COL_DET N18 O Collision Detect (MII): Asserted by the MAC PHY to indicate that a collision is occurring. In DCE Mode this signal should be connected to ground. This signal is only valid in half duplex mode, and is ignored in full duplex mode. Receive Carrier Sense (MII): Should be asserted (high) when data from the PHY (RXD[3:0) is valid. For each clock pulse 4 bits arrive from the PHY. Bit 0 is the least significant bit. In DCE mode, connect to VDD. Carrier Sense/Receive Data Valid (RMII): This signal is asserted (high) when data is valid from the PHY. For each clock pulse 2 bits arrive from the PHY. In DCE mode, this signal must be grounded. Receive Clock (MII): Timing reference for RX_DV, RX_ERR and RXD[3:0], which are clocked on the rising edge. RX_CLK frequency is 25MHz for 100Mbit/s operation and 2.5MHz for 10Mbit/s operation. In DTE mode, this is a clock input provided by the PHY. In DCE mode, this is an output derived from REF_CLK providing 2.5MHz (10Mbit/s operation) or 25MHz (100Mbit/s operation). Receive Data 0 through 3(MII): Four bits of received data, sampled synchronously with the rising edge of RX_CLK. For every clock cycle, the PHY transfers 4 bits to the DS33R11. RXD[0] is the least significant bit of the data. Data is not considered valid when RX_DV is low. Receive Data 0 through 1(RMII): Two bits of received data, sampled synchronously with REF_CLK with 100Mbit/s mode. Accepted when CRS_DV is asserted. When configured for 10Mbit/s mode, the data is sampled once every 10 clock periods. I Receive Data Valid (MII): This active high signal indicates valid data from the PHY. The data RXD is ignored if RX_DV is not asserted high. Receive Error (MII): Asserted by the MAC PHY for one or more RX_CLK periods indicating that an error has occurred. Active High indicates Receive code group is invalid. If CRS_DV is low, RX_ERR has no effect. This is synchronous with RX_CLK. In DCE mode, this signal must be grounded. Receive Error (RMII): Signal is synchronous to REF_CLK. Transmit Clock (MII): Timing reference for TX_EN and TXD[3:0]. The TX_CLK frequency is 25MHz for 100Mbit/s operation and 2.5MHz for 10Mbit/s operation. TX_CLK H19 IO In DTE mode, this is a clock input provided by the PHY. In DCE mode, this is an output derived from REF_CLK providing 2.5MHz (10Mbit/s operation) or 25MHz (100Mbit/s operation). DESCRIPTION
RX_CRS/ CRS_DV
M19
I
RX_CLK
M20
IO
RXD[0] RXD[1] RXD[2] RXD[3]
L18 L19 O L20 M18
RX_DV
K19
RX_ERR
K18
I
27 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME TXD[0] TXD[1] TXD[2] TXD[3] PIN F19 F18 E20 E19 O TYPE DESCRIPTION Transmit Data 0 through 3(MII): TXD [3:0] is presented synchronously with the rising edge of TX_CLK. TXD [0] is the least significant bit of the data. When TX_EN is low the data on TXD should be ignored. Transmit Data 0 through 1(RMII): Two bits of data TXD [1:0] presented synchronously with the rising edge of REF_CLK. Transmit Enable (MII): This pin is asserted high when data TXD [3:0] is being provided by the DS33R11. The signal is deasserted prior to the first nibble of the next frame. This signal is synchronous with the rising edge TX_CLK. It is asserted with the first bit of the preamble. Transmit Enable (RMII): When this signal is asserted, the data on TXD [1:0] is valid. This signal is synchronous to the REF_CLK. Reference Clock (RMII and MII): When in RMII mode, all signals from the PHY are synchronous to this clock input for both transmit and receive. This required clock can be up to 50MHz and should have 100ppm accuracy. REF_CLK A19 I When in MII mode in DCE operation, the DS33R11 uses this input to generate the RX_CLK and TX_CLK outputs as required for the Ethernet PHY interface. When the MII interface is used with DTE operation, this clock is not required and should be tied low. Reference Clock Output (RMII and MII): A derived clock output up to 50MHz, generated by internal division of the SYSCLKI signal. Frequency accuracy of the REF_CLKO signal will be proportional to the accuracy of the user-supplied SYSCLKI signal. This output can be used for the RMII/MII interface clock by external connection to REF_CLK. This capability eliminates the need for an additional 50 MHz (RMII) or 25MHz (MII) PHY reference oscillator. See Section 9.1.1 for more information. DCE or DTE Selection: The user must set this pin high for DCE Mode selection or low for DTE Mode. In DCE Mode, the DS33R11 MAC port can be directly connected to another MAC. In DCE Mode, the Transmit clock (TX_CLK) and Receive clock (RX_CLK) are output by the DS33R11. Note that there is no software bit selection of DCEDTES. Note that DCE Mode is only relevant when the MAC interface is in MII mode. RMII or MII Selection: Set high to configure the MAC for RMII interfacing. Set low for MII interfacing.
TX_EN
F20
O
REF_CLKO
A20
O
DCEDTES
G20
I
RMIIMIIS
G19
I
28 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE PHY MANAGEMENT BUS MDC C19 O Management Data Clock (MII): Clocks management data between the PHY and DS33R11. The clock is derived from the REF_CLK, with a maximum frequency is 1.67MHz. The user must leave this pin unconnected in the DCE Mode. MII Management data IO (MII): Data path for control information between the PHY and DS33R11. When not used, pull to logic high externally through a 10K resistor. The MDC and MDIO pins are used to write or read up to 32 Control and Status Registers in 32 PHY Controllers. This port can also be used to initiate AutoNegotiation for the PHY. The user must leave this pin unconnected in the DCE Mode. SDRAM INTERFACE
SCAS
DESCRIPTION
MDIO
C20
IO
W7
O
SDRAM Column Address Strobe: Active-low output, used to latch the column address on the rising edge of SDCLKO. It is used with commands for Bank Activate, Precharge, and Mode Register Write. SDRAM Row Address Strobe: Active-low output, used to latch the row address on rising edge of SDCLKO. It is used with commands for Bank Activate, Precharge, and Mode Register Write. SDRAM Chip Select: Active-low output enables SDRAM access. SDRAM Write Enable: This active-low output enables write operation and auto precharge. SDRAM Bank Select: These 2 bits select 1 of 4 banks for the read/write/precharge operations. Note: All SDRAM operations are controlled entirely by the DS33R11. No user programming for SDRAM buffering is required.
SRAS SDCS SWE
W9 V10 W10 Y11
O O O
SBA[0] SBA[1]
O V11
29 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME SDATA[0] SDATA[1] SDATA[2] SDATA[3] SDATA[4] SDATA[5] SDATA[6] SDATA[7] SDATA[8] SDATA[9] SDATA[10] SDATA[11] SDATA[12] SDATA[13] SDATA[14] SDATA[15] SDATA[16] SDATA[17] SDATA[18] SDATA[19] SDATA[20] SDATA[21] SDATA[22] SDATA[23] SDATA[24] SDATA[25] SDATA[26] SDATA[27] SDATA[28] SDATA[29] SDATA[30] SDATA[31] SDA[0] SDA[1] SDA[2] SDA[3] SDA[4] SDA[5] SDA[6] SDA[7] SDA[8] SDA[9] SDA[10] SDA[11] SDMASK[0] SDMASK[1] SDMASK[2] SDMASK[3] PIN W2 Y4 Y2 Y5 Y3 W5 V5 W6 V6 W4 V4 V2 V3 V1 W3 W1 Y16 Y17 V18 Y19 V19 Y20 U19 W20 U20 T19 T20 Y18 W19 V17 W17 W16 W14 W12 Y15 W15 Y14 V13 W13 Y12 V12 Y10 V14 W11 Y6 V7 V16 V15 TYPE DESCRIPTION
O
SDRAM Data Bus Bits 0 to 31: The 32 pins of the SDRAM data bus are inputs for read operations and outputs for write operations. At all other times, these pins are high-impedance. Note: All SDRAM operations are controlled entirely by the DS33R11. No user programming for SDRAM buffering is required.
O
SDRAM Address Bus 0 to 11: The 12 pins of the SDRAM address bus output the row address first, followed by the column address. The row address is determined by SDA0 to SDA11 at the rising edge of clock. Column address is determined by SDA0-SDA9 and SDA11 at the rising edge of the clock. SDA10 is used as an autoprecharge signal. Note: All SDRAM operations are controlled entirely by the DS33R11. No user programming for SDRAM buffering is required.
O
SDRAM Mask 0 through 3: When high, a write is done for that byte. The least significant byte is SDATA7 to SDATA0. The most significant byte is SDATA31 to SDATA24.
30 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME SDCLKO PIN Y8 TYPE O (4mA) DESCRIPTION SDRAM CLK Out: System clock output to the SDRAM. This clock is a buffered version of SYSCLKI. Transmit Analog Tip Output for the T1/E1/J1 Transceiver: Analog line-driver outputs. Two connections are provided to improve signal quality. These pins connect via a 1:2 step-up transformer to the network. See Section 10.25 for details. Transmit Analog Ring Output for the T1/E1/J1 Transceiver: Analog line-driver outputs. Two connections are provided to improve signal quality. These pins connect via a 1:2 step-up transformer to the network. See Section 10.25 for details. Receive Analog Tip Input for the T1/E1/J1 Transceiver: Analog input for clock recovery circuitry. These pins connect via a 1:1 transformer to the network. See Section 10.25 for details Receive Analog Ring Input for the T1/E1/J1 Transceiver: Analog input for clock recovery circuitry. These pins connect via a 1:1 transformer to the network. See Section 10.25 for details Transmit Serial Data Input to the T1/E1/J1 Framer: Transmit NRZ serial data. Sampled on the falling edge of TCLKT when the transmit-side elastic store is disabled. Sampled on the falling edge of TSYSCLK when the transmit-side elastic store is enabled. Transmit Clock for the T1/E1/J1 Transceiver: 1.544MHz or a 2.048MHz primary clock. Used to clock data from the TSERI pin through the transmit-side formatter. Transmit Channel Block for the T1/E1/J1 Transceiver: A userprogrammable output that can be forced high or low during any of the channels. Synchronous with TCLKT when the transmit-side elastic store is disabled. Synchronous with TSYSCLK when the transmit-side elastic store is enabled. Useful for locating individual channels in drop-and-insert applications, for external per-channel loopback, and for per-channel conditioning. Transmit Channel Clock for the T1/E1/J1 Transceiver: A 192kHz (T1) or 256kHz (E1) clock that pulses high during the LSB of each channel. Can also be programmed to output a gated transmit-bit clock for fractional T1/E1 applications. Synchronous with TCLKT when the transmit-side elastic store is disabled. Synchronous with TSYSCLK when the transmit-side elastic store is enabled. Useful for parallel-to-serial conversion of channel data. Transmit System Sync for the T1/E1/J1 Transceiver: Only used when the transmit-side elastic store is enabled. A pulse at this pin will establish either frame or multiframe boundaries for the transmit side. Should be tied low in applications that do not use the transmitside elastic store. Transmit Sync for the T1/E1/J1 Transceiver: A pulse at this pin will establish either frame or multiframe boundaries for the transmit side. Can be programmed to output either a frame or multiframe pulse. If this pin is set to output pulses at frame boundaries, it can also be set via TR.IOCR1.3 to output double-wide pulses at signaling frames in T1 mode.
T1/E1/J1 ANALOG LINE INTERFACE TTIP R1, R2 O
TRING
T1,T2
O
RTIP
K1
I
RRING
M1
I
T1/E1/J1 TRANSMIT FRAMER INTERFACE TSERI E3 I
TCLKT
D2
I
TCHBLK
A2
O
TCHCLK
G1
O
TSSYNC
A5
I
TSYNC
C1
I/O
31 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE DESCRIPTION Transmit System Clock for the T1/E1/J1 Transceiver: 1.544MHz, 2.048MHz, 4.096MHz, 8.192MHz, or 16.384MHz clock. Only used when the transmit-side elastic-store function is enabled. Should be tied low in applications that do not use the transmit-side elastic store. Transmit Signaling Input for the T1/E1/J1 Transceiver: When enabled, this input will sample signaling bits for insertion into outgoing PCM data stream. Sampled on the falling edge of TCLKT when the transmit-side elastic store is disabled. Sampled on the falling edge of TSYSCLK when the transmit-side elastic store is enabled. Transmit Serial Data Output from Ethernet Mapper: Output on the rising edge of TCLKE. Selective clock periods can be skipped for output of TSERO with a gapped clock input on TCLKE. The maximum data rate is 52Mbit/s. Serial Interface Transmit Clock Input to Ethernet Mapper: The clock reference for TSERO, which is output on the rising edge of the clock. TCLKE supports gapped clocking, up to a maximum frequency of 52MHz. Transmit Data Enable (Input): The transmit data enable is programmable to selectively block/enable the transmit data. The TDEN signal must occur one clock edge prior to the affected data bit. The active polarity of TDEN is programmable in register LI.TSLCR. It is recommended for both T1/E1 and T3/E3 applications that use gapped clocks. The TDEN signal is provided for interfacing to framers that do not have a gapped clock facility. Transmit Byte Sync (Output): This output can be used by an external Serial to Parallel to convert TSERO stream to byte wide data. This output indicates the last bit of the byte data sent serially on TSERO. This signal is only active in the X.86 Mode. T1/E1/J1 RECEIVE FRAMER INTERFACE RSERO H2 O Receive Serial Data for T1/E1/J1 Transceiver: Received NRZ serial data. Updated on rising edges of RCLKO when the receiveside elastic store is disabled. Updated on the rising edges of RSYSCLK when the receive-side elastic store is enabled. Receive Clock Output from the T1/E1/J1 Framer: 1.544MHz (T1) or 2.048MHz (E1) clock that is used to clock data through the receive-side framer. Normally connected to the RCLKI input. Receive Channel Block for the T1/E1/J1 Transceiver: A userprogrammable output that can be forced high or low during any of the 24 T1 or 32 E1 channels. Synchronous with RCLKO when the receive-side elastic store is disabled. Synchronous with RSYSCLK when the receive-side elastic store is enabled. Also useful for locating individual channels in drop-and-insert applications, for external per-channel loopback, and for per-channel conditioning. See the Channel Blocking Registers section.
TSYSCLK
E4
I
TSIG
B4
I
ETHERNET MAPPER TRANSMIT SERIAL INTERFACE TSERO E2 O
TCLKE
F1
I
TDEN/ TBSYNC
D5
IO
RCLKO
G3
O
RCHBLK
A1
O
32 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE DESCRIPTION Receive Channel Clock for the T1/E1/J1 Transceiver: A 192kHz (T1) or 256kHz (E1) clock that pulses high during the LSB of each channel can also be programmed to output a gated receive-bit clock for fractional T1/E1 applications. Synchronous with RCLKO when the receive-side elastic store is disabled. Synchronous with RSYSCLK when the receive-side elastic store is enabled. Useful for parallel-to-serial conversion of channel data. Receive Sync for the T1/E1/J1 Transceiver: An extracted pulse, one RCLKO wide, is output at this pin, which identifies either frame (TR.IOCR1.5 = 0) or multiframe (TR.IOCR1.5 = 1) boundaries. If set to output-frame boundaries then via TR.IOCR1.6, RSYNC can also be set to output double-wide pulses on signaling frames in T1 mode. If the receive-side elastic store is enabled, then this pin can be enabled to be an input via TR.IOCR1.4 at which a frame or multiframe boundary pulse is applied. Receive System Clock for the Transceiver: 1.544MHz, 2.048MHz, 4.096MHz, or 8.192MHz clock. Only used when the receive-side elastic-store function is enabled. Should be tied low in applications that do not use the receive-side elastic store. Receive Frame Sync (Pre Receive Elastic Store) for T1/E1/J1 Transceiver: An extracted 8kHz pulse, one RCLKO wide, is output at this pin, which identifies frame boundaries. Receive Multiframe Sync for the T1/E1/J1 Transceiver: An extracted pulse, one RCLKO wide (elastic store disabled) or one RSYSCLK wide (elastic store enabled), is output at this pin, which identifies multiframe boundaries. Receive Signaling Output: Outputs signaling bits in a PCM format. Updated on rising edges of RCLKO when the receive-side elastic store is disabled. Updated on the rising edges of RSYSCLK when the receive-side elastic store is enabled.
RCHCLK
G2
O
RSYNC
G4
I/O
RSYSCLK
F4
I
RFSYNC
A3
O
RMSYNC
U3
O
RSIG
L3
O
33 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE DESCRIPTION ETHERNET MAPPER RECEIVE SERIAL INTERFACE I Receive Serial Data Input to Ethernet Mapper: Receive Serial data arrives on the rising edge of RCLKI. Normally connected to RSERO. Serial Interface Receive Clock Input to the Ethernet Mapper: Reference clock for receive serial data on RSERI. Gapped clocking is supported, up to the maximum RCLKI frequency of 52 MHz. Receive Data Enable for the Ethernet Mapper: The receive data enable is programmable to block the receive data. The RDEN must be coincident with the RSERI data bit to be blocked or enabled. The active polarity of RDEN is programmable in register LI.RSLCR. It is recommended for both T1/E1 and T3/E3 applications that use gapped clocks. The RDEN signal is provided for interfacing to framers that do not have a gapped clock facility. Receive Byte Synchronization Input: Provides byte synchronization input to X.86 decoder. This signal will go high at the last bit of the byte as it arrives. This signal can occur at maximum rate every 8 bits. Note that a long as the R11 receives one RBSYNC indicator. The X.86 receiver will determine the byte boundary. Hence the R11 does not require a continuous 8 bit sync indicator. A new sync pulse is required if the byte boundary changes. Receive Clock Input to the T1/E1/J1 Framer: Clock used to clock data through the receive-side framer. This pin is normally connected to RDCLKO. Can be internally connected to RDCLKO by connecting the LIUC pin high. Receive Clock Output from the T1/E1/J1 LIU: Buffered recovered clock from the network. This pin is normally connected to RDCLKI. Receive Negative-Data Input: Sampled on the falling edge of RDCLKI for data to be clocked through the receive-side framer. RPOSI and RNEGI can be connected together for an NRZ interface. Can be internally connected to RNEGO by connecting the LIUC pin high. Receive Negative Data Output from the T1/E1/J1 LIU: Updated on the rising edge of RDCLKO with the bipolar data out of the line interface. This pin is normally tied to RNEGI. Receive Positive-Data Input to the T1/E1/J1 Framer: Sampled on the falling edge of RDCLKI for data to be clocked through the receive-side framer. RPOSI and RNEGI can be connected together for an NRZ interface. Can be internally connected to RPOSO by connecting the LIUC pin high. Receive Positive-Data Output from the T1/E1/J1 LIU: Updated on the rising edge of RDCLKO with bipolar data out of the line interface. This pin is normally connected to RPOSI. Receive Data from the T1/E1/J1 Framer: Updated on the rising edge of RCLKO with the data out of the receive-side framer, before passing through the Elastic Store. Serial Interface Transmit Clock Input for the T1/E1/J1 LIU: Line interface transmit clock. This pin is normally tied to TCLKO. Can be internally connected to TCLKO by connecting the LIUC pin high.
RSERI
H1
RCLKI
F2
I
RDEN/ RBSYNC
P2
I
T1/E1/J1 FRAMER/LIU INTERIM SIGNALS RDCLKI M4 I
RDCLKO
M3
O
RNEGI
L4
I
RNEGO
N2
O
RPOSI
J3
I
RPOSO
N3
O
RDATA
H3
O
TDCLKI
D1
I
34 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME TDCLKO PIN C2 TYPE O DESCRIPTION Transmit Clock Output from the T1/E1/J1 Framer: Buffered clock that is used to clock data through the transmit-side formatter (either TCLKT or RDCLKI). This pin is normally tied to TDCLKI. Transmit Negative-Data Input: Sampled on the falling edge of TDCLKI for data to be transmitted out onto the T1 line. Can be internally connected to TNEGO by connecting the LIUC pin high. TPOSI and TNEGI can be connected together in NRZ applications. Transmit Negative-Data Output: Updated on the rising edge of TCLKO with the bipolar data out of the transmit-side formatter. This pin is normally connected to TNEGI. Transmit Positive-Data Input: Sampled on the falling edge of TDCLKI for data to be transmitted out onto the T1 line. Can be internally connected to TPOSO by connecting the LIUC pin high. TPOSI and TNEGI can be connected together in NRZ applications. Transmit Positive-Data Output: Updated on the rising edge of TCLKO with the bipolar data out of the transmit-side formatter. Can be programmed to source NRZ data by the output data format (TR.IOCR1.0) control bit. This pin is normally connected to TPOSI. Transmit Data: Sampled on the falling edge of TCLKT with data to be clocked through the transmit-side formatter. This pin is normally connected to TESO. Transmit Elastic Store Output: Updated on the rising edge of TCLKT with data out of the transmit-side elastic store whether the elastic store is enabled or not. This pin is normally connected to TDATA.
TNEGI
C3
I
TNEGO
D3
O
TPOSI
B3
I
TPOSO
E1
O
TDATA
A4
I
TESO
D4
O
35 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE DESCRIPTION Line Interface Unit Connect: When a logic low is present on this input pin, the T1/E1/J1 Framer and LIU are not internally connected. The line interface circuitry will be separated from the framer/formatter circuitry and the TPOSI, TNEGI, TDCLKI, RPOSI, RNEGI, and RDCLKI input pins will be active. LIUC B2 I When a logic high is present on this input pin, the T1/E1/J1 Framer is internally connected to the LIU. The TPOSI, TNEGI, TDCLKI, RPOSI, RNEGI, RDCLKI input pins are deactivated. When LIUC is connected high, the TPOSI, TNEGI, TDCLKI, RPOSI, RNEGI, and RDCLKI pins should be tied low. Reset for the Ethernet Mapper: An active low signal on this pin resets the internal registers and logic of the protocol conversion device. This pin should remain low until power, SYSCLKI, RX_CLK, and TX_CLK are stable, then set high for normal operation. This input requires a clean edge with a rise time of 25ns or less to properly reset the device. Test/Reset for the T1/E1/J1 Transceiver: A dual-function pin. A zero-to-one transition issues a hardware reset to the transceiver register set. A reset clears all configuration registers. Configuration register contents are set to zero. Leaving TSTRST high will tri-state all output and I/O pins (including the parallel control port). Set low for normal operation. Useful in board-level testing. Mode Control for Processor Interface: 00 = Read/Write Strobe Used (Intel Mode) 01 = Data Strobe Used (Motorola Mode) 10 = Reserved. Do not use. 11 = Reserved. Do not use. Queue Overflow for Ethernet Mapper: This pin goes high when the transmit or receive queue has overflowed. This pin will go low when the high watermark is reached again. T1/E1/J1 Receive Loss-of-Sync/Loss-of-Transmit Clock: A dual function output that is controlled by the CCR1.0 control bit. This pin can be programmed to either toggle high when the synchronizer is searching for the frame and multiframe or to toggle high if the TCLKT pin has not been toggled for 5ms. T1/E1/J1 Receive Carrier Loss: Set high when the T1/E1/J1 line interface detects a carrier loss. T1/E1/J1 Receive Signaling-Freeze Output: Set high when the signaling data is frozen by either automatic or manual intervention. Used to alert downstream equipment of the condition.
HARDWARE AND STATUS PINS
RST
A8
I
TSTRST
C4
I
MODEC[0], MODEC[1]
B19, B20
I
QOVF
H18
O
RLOS/LTC
N1
O
RCL RSIGF
B5 P3
O O
36 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE SYSTEM CLOCKS System Clock In for Ethernet Mapper: 100MHz System Clock input to the DS33R11, used for internal operation. This clock is buffered and provided at SDCLKO for the SDRAM interface. The DS33R11 also provides a divided version output at the REF_CLKO pin. A clock supply with 100ppm frequency accuracy is suggested. Master Clock Input for the T1/E1/J1 Transceiver: A (50ppm) clock source. This clock is used internally for both clock/data recovery and for the jitter attenuator for both T1 and E1 modes. The clock rate can be 16.384MHz, 8.192MHz, 4.096MHz, or 2.048MHz. When using the transceiver in T1-only operation a 1.544MHz (50ppm) clock source can be used. Backplane Clock from T1/E1/J1 Transceiver: A user-selectable synthesized clock output that is referenced to the clock that is output at the RCLKO pin. Eight Times Clock from the T1/E1/J1 Transceiver: An 8x clock that is locked to the recovered network clock provided from the clock/data recovery block (if the jitter attenuator is enabled on the receive side) or from the TDCLKI pin (if the jitter attenuator is enabled on the transmit side). Quartz Crystal Driver for the T1/E1/J1 Transceiver: A quartz crystal of 2.048MHz (optional 1.544MHz in T1-only operation) can be applied across MCLK and XTALD instead of a clock source at MCLK. Leave open circuited if a clock source is applied at MCLK. DESCRIPTION
SYSCLKI
V8
I
MCLK
H4
I
BPCLK
B1
O
8XCLK
K4
O
XTALD
J4
O
37 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME PIN TYPE JTAG INTERFACE JTCLK1 A7 Ipu JTAG Clock 1 for the Ethernet Mapper: This signal is used to shift data into JTDI1 on the rising edge and out of JTDO1 on the falling edge. JTAG Data In 1 for the Ethernet Mapper: Test instructions and data are clocked into this pin on the rising edge of JTCLK1. This pin has a 10kW pullup resistor. JTAG Data Out 1 for the Ethernet Mapper: Test instructions and data are clocked out of this pin on the falling edge of JTCLK1. If not used, this pin should be left unconnected. JTAG Mode Select 1 for the Ethernet Mapper: This pin is sampled on the rising edge of JTCLK1 and is used to place the test access port into the various defined IEEE 1149.1 states. This pin has a 10kW pullup resistor. JTAG Reset 1 for the Ethernet Mapper: JTRST1 is used to asynchronously reset the test access port controller. After power up, a rising edge on JTRST1 will reset the test port and cause the device I/O to enter the JTAG DEVICE ID mode. Pulling JTRST1 low restores normal device operation. JTRST1 is pulled HIGH internally via a 10kW resistor operation. If boundary scan is not used, this pin should be held low. JTAG Clock 2 for the T1/E1/J1 Transceiver: This signal is used to shift data into JTDI1 on the rising edge and out of JTDO1 on the falling edge. JTAG Data In 2 for the T1/E1/J1 Transceiver: Test instructions and data are clocked into this pin on the rising edge of JTCLK2. This pin has a 10kW pullup resistor. JTAG Data Out 2 for the T1/E1/J1 Transceiver: Test instructions and data are clocked out of this pin on the falling edge of JTCLK2. If not used, this pin should be left unconnected. JTAG Mode Select 2 for the T1/E1/J1 Transceiver: This pin is sampled on the rising edge of JTCLK2 and is used to place the testaccess port into the various defined IEEE 1149.1 states. This pin has a 10kW pullup resistor. JTAG Reset 2 for the T1/E1/J1 Transceiver: JTRST2 is used to asynchronously reset the test access port controller. After powerup, JTRST2 must be toggled from low to high. This action will set the device into the JTAG DEVICE ID mode. Normal device operation is restored by pulling JTRST2 low. JTRST2 is pulled HIGH internally via a 10kW resistor operation. DESCRIPTION
JTDI1
C9
Ipu
JTDO1
B7
Oz
JTMS1
C8
Ipu
JTRST1
C7
Ipu
JTCLK2
A6
Ipu
JTDI2
B6
Ipu
JTDO2
C5
Oz
JTMS2
B9
Ipu
JTRST2
B8
Ipu
38 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver NAME RVDD RVSS TVDD TVSS DVDD DVSS PIN K3, L1 J1, J2, K2, L2, M2 U1 P1, R3, T3, U2 D1-D17, E17 N4, P4, R4, T4 B10, B15, C12, F3, J18, J20, P18, P19, R19, R20, V9, Y9, Y13 D20, F17, G17, G18, H17, J17, K17, L17, M17, N17, P17, R17, R18, T17, T18, U17 A15, C10, D8, D9, D10, D18, D19, E18, H20, J19, K20, N19, N20, P20, U4-U16, U18, V20, W8, W18, Y1, Y7 A9, C6, D6 TYPE POWER SUPPLIES -- -- - - -- -- Receive Analog Positive Supply: Connect to 3.3V power supply. Receive Analog Signal Ground: Connect to the common supply ground. Transmit Analog Positive Supply: Connect to 3.3V power supply. Transmit Analog Signal Ground: Connect to the common supply ground. Digital Positive Supply: Connect to 3.3V power supply. Digital Signal Ground: Connect to the common supply ground. DESCRIPTION
VDD1.8
I
VDD1.8: Connect to 1.8V power supply.
VDD3
I
VDD3.3: Connect to 3.3V power supply.
VSS
I
VSS: Connect to the common supply ground.
N.C.
--
No Connection. Do not connect these pins. Leave these pins open.
39 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 7-1. 256-Ball BGA Pinout
1 2 3 4 5 6 7
JTCLK1
8
RST JTRST2
9
N.C.
10
INT
11
CS RD/DS WR/RW
12
D6
13
D3
14
D0
15
VSS
16
A6
17
A3
18
A0
19
REF_CLK MODEC [0] MDC
20
REF_ CLKO MODEC [1] MDIO
A RCHBLK TCHBLK RFSYNC TDATA TSSYNC JTCLK2 B BPCLK
LIUC TPOSI TSIG RCL JTDI2
JTDO1
JTRST1 CST
JTMS2
VDD1.8
D7
D4
D1
VDD1.8
A7
A4
A1
C TSYNC TDCLKO D TDCLKI E TPOSO F
TCLKE TCLKT
TNEGI
TSTRST
JTDO2 TDEN/ TBSYNC
N.C.
JTMS1
JTDI1
VSS
VDD1.8
D5
D2
A9
A8
A5
A2
TNEGO
TESO
N.C.
VSS
VSS
VSS
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
VSS
VSS TXD [3] TXD [0] RMIIMIIS
VDD3 TXD [2] TX_EN DCE DTES VSS
TSERO
TSERI
TSYSCLK
DVDD
VSS TXD [1] VDD3
RCLKI
VDD1.8 RSYSCLK
VDD3
G TCHCLK RCHCLK RCLKO H J K L
RSERI RSERO RDATA
RSYNC
VDD3
MCLK
VDD3
QOVF
TX_CLK
RVSS
RVSS
RPOSI
XTALD
VDD3
VDD1.8
VSS
VDD1.8
RTIP
RVSS
RVDD
8XCLK
VDD3
RX_ERR RXD [0] RXD [3] COL_DEt
RX_DV RXD [1]
VSS RXD [2]
RVDD
RVSS
RSIG
RNEGI
VDD3
M RRING N P R T U V W Y
RLOS/ LTC TVSS
RVSS
RDCLKO RDCLKI
VDD3
RX_CRS / RX_CLK CRS_DV VSS VSS
RNEGO RDEN/ RBSYNC TTIP
RPOSO
DVSS
VDD3
RSIGF
DVSS
VDD3
VDD1.8
VDD1.8
VSS
TTIP
TVSS
DVSS
VDD3
VDD3
VDD1.8 SDATA [25] SDATA [22] SDATA [20] SDATA [28] SDATA [19]
VDD1.8 SDATA [26] SDATA [24] VSS SDATA [23] SDATA [21]
TRING
TRING
TVSS
DVSS
VDD3
VDD3
TVDD SDATA [13] SDATA [15] VSS
TVSS SDATA [11] SDATA [0] SDATA [2]
RMSYNC SDATA [12] SDATA [14] SDATA [4]
VSS SDATA [10] SDATA [9] SDATA [1]
VSS SDATA [6] SDATA [5] SDATA [3]
VSS SDATA [8] SDATA [7] SDMASK [0]
VSS
VSS
VSS
VSS
SDCS SWE
VSS SBA [1] SDA [11] SBA [0]
VSS SDA [8] SDA [1] SDA [7]
VSS SDA [5] SDA [6] VDD1.8
VSS SDA [10] SDA [0] SDA [4]
VSS
VSS
VDD3 SDATA [29] SDATA [30] SDATA [17]
VSS SDATA [18] VSS SDATA [27]
SDMASK SYSCLKI [1]
SCAS
VDD1.8
SRAS
SDMASK SDMASK [3] [2] SDA [3] SDA [2] SDATA [31] SDATA [16]
VSS
VSS
SDCLKO
VDD1.8
SDA [9]
40 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
8
FUNCTIONAL DESCRIPTION
The DS33R11 provides interconnection and mapping functionality between Ethernet packet LANs and T1/E1/J1 WAN Time-Division Multiplexed (TDM) systems. The device is composed of a 10/100 Ethernet MAC, packet arbiter, committed information rate controller (CIR), HDLC/X.86 (LAPS) mapper, SDRAM interface, control ports, bit error-rate tester (BERT), and integrated T1/E1/J1 transceiver. The packet interface consists of a MII/RMII Ethernet PHY interface. The Ethernet interface can be configured for 10Mbit/s or 100Mbit/s service. The DS33R11 encapsulates Ethernet traffic with HDLC or X.86 (LAPS) encoding to be transmitted over a T1, E1, or J1 line. The T1/E1/J1 interface also receives encapsulated Ethernet packets and transmits the extracted packets over the Ethernet ports. Access is provided to the signals between the serial port and the integrated T1/E1/J1 transceiver. The Ethernet packet interface supports MII and RMII interfaces, allowing the DSZ33R11 to connect to commercially available Ethernet PHY and MAC devices. The Ethernet interface can be configured for 10Mbit/s or 100Mbit/s service, in DTE and DCE configurations. The DS33R11 MAC interface rejects frames with bad FCS and short frames (less than 64 bytes). Ethernet frames are queued and stored in external 32-bit SDRAM. The DS33R11 SDRAM controller enables connection to a 128Mb SDRAM without external glue logic, at clock frequencies up to 100MHz. The SDRAM is used for both the transmit and receive data queues. The receive queue stores data to be sent from the packet interface to the WAN serial interface. The transmit queue stores data to be sent from the WAN serial interface to the Ethernet LAN packet interface. The external SDRAM can accommodate up to 8192 frames with a maximum frame size of 2016 bytes. The sizing of the queues can be adjusted by software. The user can also program high and low watermarks for each queue that can be used for automatic or manual flow control. The packet data stored in the SDRAM is encapsulated in HDLC or X.86 (LAPS) to be transmitted over the WAN interface. The device also provides the capability for bit and packet scrambling. The WAN interface also receives encapsulated Ethernet packets and transmits the extracted packets over the Ethernet port. The WAN serial port can operate with a gapped clock, and is designed to be connected to the integrated T1/E1/J1 transceiver for transmission. The DS33R11 can be configured through an 8-bit microprocessor interface port. Diagnostic capabilities include loopbacks, PRBS pattern generation/detection, and 16-bit loop-up/loop-down code generation and detection. The DS33R11 provides two on-board clock dividers for the system-clock input and reference-clock input for the 802.3 interfaces, further reducing the need for ancillary devices. The integrated transceiver is a software-selectable T1, E1, or J1 single-chip transceiver (SCT) for short-haul and long-haul applications. The transceiver is composed of an LIU, framer, HDLC controllers, and a TDM backplane interface, and is controlled by the 8-bit parallel port. The transceiver is software compatible with the DS2155 and DS2156. The LIU is composed of transmit and receive interfaces and a jitter attenuator. The transmit interface is responsible for generating the necessary waveshapes for driving the network and providing the correct source impedance depending on the type of media used. T1 waveform generation includes DSX-1 line build-outs as well as CSU line build-outs of -7.5dB, -15dB, and -22.5dB. E1 waveform generation includes G.703 waveshapes for both 75W coax and 120W twisted cables. The receive interface provides network termination and recovers clock and data from the network. The receive sensitivity adjusts automatically to the incoming signal and can be programmed for 0 to 43dB or 0 to 12dB for E1 applications and 0 to 30dB or 0 to 36dB for T1 applications. The jitter attenuator removes phase jitter from the transmitted or received signal. The crystal-less jitter attenuator requires only a 2.048MHz MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK in T1 applications) and can be placed in either transmit or receive data paths. An additional feature of the LIU is a CMI coder/decoder for interfacing to optical networks. On the transmit side, clock, data, and frame-sync signals are provided to the framer by the backplane interface section. The framer inserts the appropriate synchronization framing patterns, alarm information, calculates and inserts the CRC codes, and provides the B8ZS/HDB3 (zero code suppression) and AMI line coding. The receiveside framer decodes AMI, B8ZS, and HDB3 line coding, synchronizes to the data stream, reports alarm information, counts framing/coding/CRC errors, and provides clock/data and frame-sync signals to the backplane interface section. Both the transmit and receive path of the integrated T1/E1/J1 transceiver also have two HDLC controllers. The HDLC controllers transmit and receive data through the framer block. The HDLC controllers can be assigned to any 41 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver time slot, group of time slots, portion of a time slot or to FDL (T1) or Sa bits (E1). Each controller has 128-byte FIFOs, thus reducing the amount of processor overhead required to manage the flow of data. In addition, built-in support for reducing the processor time is required in SS7 applications. The backplane interface provides a versatile method of sending and receiving data from the host system. Elastic stores provide a method for interfacing to asynchronous systems, converting from a T1/E1 network to a 2.048MHz, 4.096MHz, 8.192MHz, or N x 64kHz system backplane. The elastic stores also manage slip conditions (asynchronous interface).
8.1
Processor Interface
Microprocessor control of the DS33R11 is accomplished through the interface pins of the microprocessor port. The 8-bit parallel data bus can be configured for Intel or Motorola modes of operation with the two MODEC[1:0] pins. When MODEC[1:0] = 00, bus timing is in Intel mode, as shown in Figure 13-9 and Figure 13-10. When MODEC[1:0] = 01, bus timing is in Motorola mode, as shown in Figure 13-11 and Figure 13-12. The address space is mapped through the use of 10 address lines, A0-A9. Multiplexed Mode is not supported on the processor interface. See the timing diagrams in AC Electrical Characteristics in Section 13 for more details. The Chip Select (CS) pin must be brought to a logic low level to gain read and write access to the microprocessor port. With Intel timing selected, the Read (RD) and Write (WR) pins are used to indicate read and write operations and latch data through the interface. With Motorola timing selected, the Read-Write (RW) pin is used to indicate read and write operations while the Data Strobe (DS) pin is used to latch data through the interface. The interrupt output pin (INT) is an open-drain output that will assert a logic-low level upon a number of software maskable interrupt conditions. This pin is normally connected to the microprocessor interrupt input. The register map is shown in Table 11-1.
8.1.1
Read-Write/Data Strobe Modes
The processor interface can operate in either read-write strobe mode or data strobe mode. When MODEC[1:0] = 00 the read-write strobe mode is enabled and a negative pulse on RD performs a read cycle, and a negative pulse on WR performs a write cycle. When MODEC[1:0] pins = 01 the data strobe mode is enabled and a negative pulse on DS when RW is high performs a read cycle, and a negative pulse on DS when RW is low performs a write cycle. The read-write strobe mode is commonly called the "Intel" mode, and the data strobe mode is commonly called the "Motorola" mode.
8.1.2
Clear on Read
The latched status registers will clear on a read access. It is important to note that in a multi-task software environment, the user should handle all status conditions of each register at the same time to avoid inadvertently clearing status conditions. The latched status register bits are carefully designed so that an event occurrence cannot collide with a user read access.
8.1.3
Interrupt and Pin Modes
The interrupt (INT) pin is configurable to drive high or float when not active. The INTM bit controls the pin configuration, when it is set the INT pin will drive high when not active. After reset, the INT pin is in high-impedance mode until an interrupt source is active and enabled to drive the interrupt pin.
42 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9 ETHERNET MAPPER
9.1
* *
Ethernet Mapper Clocks
Serial Transmit Data (TCLKE) and Serial Receive Data (RCLKI) clock inputs are used to transfer data from the serial interface. These clocks can be continuous or gapped. System Clock (SYSCLKI) input. Used for internal operation. This clock input cannot be a gapped clock. A clock supply with 100ppm frequency accuracy is suggested. A buffered version of this clock is provided on the SDCLKO pin for the operation of the SDRAM. A divided and buffered version of this clock is provided on REF_CLKO for the RMII/MII interface. Packet Interface Reference clock (REF_CLK) input that can be 25MHz or 50MHz. This clock is used as the timing reference for the RMII/MII interface. The user can utilize the built-in REF_CLKO output clock to drive this input. The Transmit and Receive clocks for the MII Interface (TX_CLK and RX_CLK). In DTE mode, these are input pins and accept clocks provided by an Ethernet PHY. In the DCE mode, these are output pins and will output an internally generated clock to the Ethernet PHY. The output clocks are generated by internal division of REF_CLK. In RMII mode, only the REF_CLK input is used. REF_CLKO is an output clock that is generated by dividing the 100MHz System clock (SYSCLKI) by 2 or 4. This output clock can be used as an input to REF_CLK, allowing the user to have one less oscillator for the system. A Management Data Clock (MDC) output is derived from SYSCLKI and is used for information transfer between the internal Ethernet MAC and external PHY. The MDC clock frequency is 1.67MHz.
The DS33R11 clocks sources and functions are as follows:
*
*
*
*
Clocking of the integrated T1/E1/J1 tansceiver is discussed in Section 10.1. The following table provides the different clocking options for the Ethernet interface.
Table 9-1. Clocking Options for the Ethernet Interface
RMIIMIIS PIN 0 (MII) 0 (MII) 0 (MII) 1 (RMII) 1 (RMII) SPEED 10 Mbps 10 Mbps 100 Mbps 10 Mbps 100 Mbps DCE/ DTE DTE DCE DCE -- -- REF_CLKO OUTPUT 25MHz 25MHz 25MHz 50MHz 50MHz REF_CLK INPUT 25MHz 100ppm 25MHz 100ppm 25MHz 100ppm 50MHz 100ppm 50MHz 100ppm RX_CLK Input from PHY 2.5MHz (Output) 25MHz (Output) Not Applicable Not Applicable TX_CLK Input from PHY 2.5MHz (Output) 25MHz (Output) Not Applicable Not Applicable MDC OUTPUT 1.67MHz 1.67MHz 1.67MHz 1.67MHz 1.67MHz
43 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-1. Clocking for the DS33R11
TSYSCLK TCHBLK TCHCLK TCLKT TDCLKI TDCLKO MCLK XTALD 8XCLK BPCLK TCLKE TDEN
mP Port CLAD TRANSMIT SERIAL PORT CIR CONTROLLER TRANSMIT FRAMER TRANSMIT LIU PACKET HDLC/X.86 CLAD SYSCLKI REF_CLKO RX_CLK ETHERNET MAC JTAG1 SDRAM PORT RSYSCLK RCHBLK RCHCLK RCLKO JTCLK2 RDCLKI RDCLKO RCLKI RDEN SDCLK JTCLK1 REF_CLK
TTIP TRING
MUX
T1/E1/J1 TRANSCEIVER
HDLC
ETHERNET MAPPER
BERT
HDLC
BERT
ARBITER
RECEIVIE FRAMER
RECEIVE SERIAL PORT
RRING
MUX
PACKET HDLC/X.86
RTIP
RECEIVE LIU
TX_CLK MDC
JTAG2
NOTE THAT THE CLOCKING OPTIONS OF THE INTEGRATED T1/E1/J1 TANSCEIVER ARE DISCUSSED IN SECTION 10.1.
44 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.1.1
Ethernet Interface Clock Modes
The Ethernet PHY interface has several different clocking requirements, depending on the mode of operation. The user has the option of using the internally generated REF_CLKO output to simplify the system design. Table 9-1 outlines the possible clocking modes for the Ethernet Interface. The buffered REF_CLKO output is generated by division of the 100MHz system clock input by the user on SYSCLKI. The frequency of the REF_CLKO pin is automatically determined by the DS33R11 based on the state of the RMIIMIIS pin. The REF_CLKO output can be used as a REF_CLK for the Ethernet Interface by connecting REF_CLKO to REF_CLK. The REF_CLKO function can be turned off with the GL.CR1.RFOO bit. In RMII mode, receive and transmit timing is always synchronous to a 50 MHz clock input on the REF_CLK pin. The source of REF_CLK is expected to be the external PHY. The user has the option of using the 50MHz REF_CLKO output as the timing source for the PHY. More information on RMII mode can be found in Section 9.15.2. While using MII mode with DTE operation, the MII clocks (RX_CLK and TX_CLK) are inputs that are expected to be provided by the external PHY. While using MII mode with DCE operation, the MII clocks (TX_CLK and RX_CLK) are output by the DS33R11, and are derived from the 25MHz REF_CLK input. Any 25MHz reference may be used, but the user may choose to use the REF_CLKO output to avoid adding another system clock. More information on MII mode can be found in Section 9.15.1.
9.1.2
Serial Interface Clock Modes
The serial interface timing is determined by the line clocks. Both the transmit and receive clocks (TCLKE and RCLKI) are inputs, and can be gapped.
45 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.2
Resets and Low Power Modes
The external RST pin and the global reset bit in GL.CR1 create an internal global reset signal. The global reset signal resets the status and control registers on the chip (except the GL.CR1.RST bit) to their default values and resets all the other flops to their reset values. The processor bus output signals are also placed in high-impedance mode when the RST pin is active (low). The global reset bit (GL.CR1.RST) stays set after a one is written to it, but is reset to zero when the external RST pin is active or when a zero is written to it. Allow 5ms after initiating a reset condition for the reset operation to complete. The Serial Interface reset bit in LI.RSTPD resets all the status and control registers on the serial interface to their default values, except for the LI.RSTPD.RST bit. The serial interface includes the HDLC encoder/decoder, X86 encoder and decoder and the corresponding serial port. The serial interface reset bit (LI.RSTPD.RST) stays set after a one is written to it, but is reset to zero when the global reset signal is active or when a zero is written to it.
Table 9-2. Reset Functions
RESET FUNCTION Hardware Device Reset Hardware JTAG Reset Global Software Reset Serial Interface Reset Queue Pointer Reset LOCATION
RST Pin JTRST Pin
COMMENTS Transition from a logic 0 to a logic 1 resets the device. Resets the JTAG test port. Writing to this bit resets the device. Writing to this bit resets the Serial Interface. Writing to this bit resets the Queue Pointers
GL.CR1 LI.RSTPD GL.C1QPR
There are several features in the DS33R11 to reduce power consumption. The reset bit in the LI.RSTPD and register also place the Serial interface in a low-power mode. Additionally, the RST pin may be held low indefinitely to keep the entire device in a low-power mode. Note that exiting the low-power condition requires re-initialization and configuration. The T1/E1/J1 transceiver contains an on-chip power-up reset function that automatically clears the writeable register space immediately after power is supplied to the transceiver. The user can issue a chip reset at any time. Issuing a reset disrupts traffic flowing through the transceiver until the device is reprogrammed. The reset can be issued through hardware using the TSTRST pin or through software using the SFTRST function in the master mode register. The LIRST (TR.LIC2.6) should be toggled from 0 to 1 to reset the line interface circuitry. (It takes the transceiver about 40ms to recover from the LIRST bit being toggled.) Finally, after the TSYSCLK and RSYSCLK inputs are stable, the receive and transmit elastic stores should be reset (this step can be skipped if the elastic stores are disabled).
46 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.3
Initialization and Configuration
EXAMPLE DEVICE INITIALIZATION SEQUENCE: STEP 1: Apply 3.3V supplies, then apply 1.8V supplies. STEP 2: Reset the integrated Ethernet Mapper by pulling the RST pin low or by using the software reset bits outlined in Section 9.2. Clear all reset bits. Allow 5ms for the reset recovery. STEP 3: Reset the integrated T1/E1/J1 Transceiver through hardware using the TSTRST pin or through software using the SFTRST function in the master mode register. STEP 4: The LIRST (TR.LIC2.6) should be toggled from 0 to 1 to reset the line interface circuitry. Allow 40ms for the reset recovery. STEP 5: Check the Ethernet Mapper Device ID in the GL.IDRL and GL.IDRH registers. STEP 6: Check the T1/E1/J1 Transceiver Device ID in the TR.IDR register. STEP 7: Configure the system clocks. Allow the clock system to properly adjust. STEP 8: Initialize the entire remainder of the register space with 00h (or otherwise if specifically noted in the register's definition), including the reserved bits and reserved register locations. STEP 9: Write FFFFFFFFh to the MAC indirect addresses 010Ch through 010Fh. STEP 10: Setup connection in the GL.CON1 register. STEP 11: Configure the Serial Port register space as needed. STEP 12: Configure the Ethernet Port register space as needed. STEP 13: Configure the Ethernet MAC indirect registers as needed. STEP 14: Configure the T1/E1/J1 Framer as needed. STEP 15: Configure the T1/E1/J1 LIU as needed. STEP 16: Configure the external Ethernet PHY through the MDIO interface. STEP 17: Clear all counters and latched status bits. STEP 18: Set the queue size in the Arbiter and reset the queue pointers for the Ethernet and serial interfaces. STEP 19: After the TSYSCLK and RSYSCLK inputs to the T1/E1/J1 transceiver are stable, the receive and transmit elastic stores should be reset (this step can be skipped if the elastic stores are disabled). STEP 20: Enable Interrupts as needed. STEP 21: Begin handling interrupts and latched status events.
9.4
Global Resources
In order to maintain software compatibility with the multiport devices in the product family, a set of global registers are located at 0F0h-0FFh. The global registers include Global resets, global interrupt status, interrupt masking, clock configuration, and the Device ID registers. See the Global Register Definitions in Table 11-2.
9.5
Per-Port Resources
Multiport devices in this product family share a common set of global registers, BERT, and arbiter. All other resources are per-port.
47 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.6
Device Interrupts
Figure 9-2 diagrams the flow of interrupt conditions from their source status bits through the multiple levels of information registers and mask bits to the interrupt pin. When an interrupt occurs, the host can read the Global Latched Status registers GL.LIS, GL.SIS, GL.BIS, and GL.TRQIS to initially determine the source of the interrupt. The host can then read the LI.TQCTLS, LI.TPPSRL, LI.RPPSRL, LI.RX86S, SU.QCRLS, or BSRL registers to further identify the source of the interrupt(s). In order to maintain software compatibility with the multiport devices in the product family, the global interrupt status and interrupt enable registers have been preserved, but do not need to be used. If GL.TRQIS is determined to be the interrupt source, the host will then read the LI.TPPSRL and LI.RPPSRL registers for the cause of the interrupt. If GL.LIS is determined to be the interrupt source, the host will then read the LI.TQCTLS, LI.TPPSRL, LI.RPPSRL, and LI.RX86S registers for the source of the interrupt. If GL.SIS is the source, the host will then read the SU.QCRLS register for the source of the interrupt. If GL.BIS is the source, the host will then read the BSRL register for the source of the interrupt. All Global Interrupt Status Register bits are real-time bits that will clear once the appropriate interrupt has been serviced and cleared, as long as no additional, enabled interrupt conditions are present in the associated status register. All Latched Status bits must be cleared by the host writing a "1" to the bit location of the interrupt condition that has been serviced. In order for individual status conditions to transmit their status to the next level of interrupt logic, they must be enabled by placing a "1" in the associated bit location of the correct Interrupt Enable Register. The Interrupt enable registers are LI.TPPSRIE, LI.RPPSRIE, LI.RX86LSIE, BSRIE, SU.QRIE, GL.LIE, GL.SIE, GL.BIE, and GL.TRQIE. Latched Status bits that have been enabled via Interrupt Enable registers are allowed to pass their interrupt conditions to the Global Interrupt Status Registers. The Interrupt enable registers allow individual Latched Status conditions to generate an interrupt, but when set to zero, they do not prevent the Latched Status bits from being set. Therefore, when servicing interrupts, the user should AND the Latched Status with the associated Interrupt Enable Register in order to exclude bits for which the user wished to prevent interrupt service. This architecture allows the application host to periodically poll the latched status bits for noninterrupt conditions, while using only one set of registers. Note the bitorders of SU.QRIE and SU.QCRLS are different. Note that the inactive state of the interrupt output pin is configurable. The INTM bit in GL.CR1 controls the inactive state of the interrupt pin, allowing selection of a pull-up resistor or active driver. The interrupt structure is designed to efficiently guide the user to the source of an enabled interrupt source. The latched status bits for the interrupting entity must be read to clear the interrupt. Also reading the latched status bit will reset all bits in that register. During a reset condition, interrupts cannot be generated. The interrupts from any source can be blocked at a global level by the placing a zero in the global interrupt enable registers (GL.LIE, GL.SIE, GL.BIE, and GL.TRQIE). Reading the Latched Status bit for all interrupt generating events will clear the interrupt status bit and Interrupt signal will be de-asserted. Note that the integrated T1/E1/J1 transceiver also generates interrupts, as discussed in Section 10.3.
48 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-2. Device Interrupt Information Flow Diagram
Receive FCS Errored Packet Receive Aborted Packet Receive Invalid Packet Detected Receive Small Packet Detected Receive Large Packet Detected Receive FCS Errored Packet Count Receive Aborted Packet Count Receive Size Violation Packet Count Transmit Errored Packet Insertion Finished SAPI High is not equal to LI.TRX86SAPIH SAPI Low is not equal to LI.TRX86SAPIL Control is not equal to LI.TRX8C Address is not equal to LI.TRX86A Transmit Queue FIFO Overflowed Transmit Queue Overflow Transmit Queue for Connection Exceeded Low Threshold Transmit Queue for Connection Exceeded High Threshold Receive Queue FIFO Overflowed Receive Queue Overflow Receive Queue for Connection Exceeded Low Threshold Receive Queue for Connection Exceeded High Threshold Performance Monitor Update Bit Error Detected Bit Error Count Out Of Synchronization
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
LI.RPPSRIE
Drawing Legend:
Interrupt Status Registers Interrupt Enable Registers Register Name
LI.RPPSL
Register Name
LI.TPPSRIE
LI.TPPSRL
LI.RX86LSIE
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
GL.TRQIS GL.LIS
LI.RX86S
LI.TQCTLS
LI.TQTIE
GL.LIE
GL.TRQIE
GL.SIS
SU.QCRLS
SU.QRIE
GL.SIE
BSRIE
49 of 338
Interrupts from T1/E1/J1 Transceiver
GL.BIS
BSRL
GL.BIE
Interrupt Pin
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.7
Interrupt Information Registers
The interrupt information registers provide an indication of which status registers (SR1 through SR9) are generating an interrupt. When an interrupt occurs, the host can read TR.IIR1 and TR.IIR2 to quickly identify which of the nine status registers are causing the interrupt.
9.8
Status Registers
When a particular event or condition has occurred (or is still occurring in the case of conditions), the appropriate bit in a status register is set to a 1. All of the status registers operate in a latched fashion. This means that if an event or condition occurs a bit is set to a 1. It remains set until the user reads that bit. An event bit is cleared when it is read and it is not set again until the event has occurred again. Condition bits such as RBL, RLOS, etc., remain set if the alarm is still present. The user always proceeds a read of any of the status registers with a write. The byte written to the register informs the device which bits the user wishes to read and have cleared. The user writes a byte to one of these registers, with a 1 in the bit positions the user wishes to read and a 0 in the bit positions the user does not wish to obtain the latest information on. When a 1 is written to a bit location, the read register is updated with the latest information. When a 0 is written to a bit position, the read register is not updated and the previous value is held. A write to the status registers is immediately followed by a read of the same register. This write-read scheme allows an external microcontroller or microprocessor to individually poll certain bits without disturbing the other bits in the register. This operation is key in controlling the device with higher order languages. Status register bits are divided into two groups, condition bits and event bits. Condition bits are typically network conditions such as loss-of-sync or all-ones detect. Event bits are typically markers such as the one-second timer, elastic store slip, etc. Each status register bit is labeled as a condition or event bit. Some of the status registers have bits for both the detection of a condition and the clearance of the condition. For example, TR.SR2 has a bit that is set when the device goes into a loss-of-sync state (TR.SR2.0, a condition bit) and a bit that is set (TR.SR2.4, an event bit) when the loss-of-sync condition clears (goes in sync). Some of the status register bits (condition bits) do not have a separate bit for the "condition clear" event but rather the status bit can produce interrupts on both edges, setting and clearing. These bits are marked as double interrupt bits. An interrupt is produced when the condition occurs and when it clears.
9.9
Information Registers
Information registers operate the same as status registers except they cannot cause interrupts. They are all latched except for TR.INFO7 and some of the bits in TR.INFO5 and TR.INFO6. TR.INFO7 register is a read-only register. It reports the status of the E1 synchronizer in real time. TR.INFO7 and some of the bits in TR.INFO6 and TR.INFO5 are not latched and it is not necessary to precede a read of these bits with a write.
9.10 Serial Interface
The Serial (WAN) interface is intended to be connected to the integrated T1/E1/J1 Transceiver. However, the interface supports time-division multiplexed, serial data input and output up to 52 Mbit/s. The Serial interface receives and transmits encapsulated Ethernet packets. The Serial Interface block consists of the physical serial port and HDLC / X.86 engine. The physical interface consists of a Transmit Data, Transmit Clock, Transmit Enable, Receive Data, Receive Clock, and Receive Enable. The WAN serial port can operate with a gapped clock, and can be connected to a framer, electrical LIU, optical transceiver, or T/E-Carrier transceiver for transmission to the WAN.
50 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.11 Connections and Queues
The multi-port devices in this product family provide bidirectional cross-connections between the multiple Ethernet ports and Serial ports when operating in software mode. A single connection is preserved in this single-port device to provide software compatibility with multi-port devices. The connection will have an associated transmit and receive queue. Note that the terms "Transmit Queue" and "Receive Queue" are with respect to the Ethernet Interface. The Receive queue is for data arriving from Ethernet interface to be transmitted to the WAN interface. The Transmit queue is for data arriving from the WAN to be transmitted to the Ethernet interface. Hence the transmit and receive direction terminology is the same as is used for the Ethernet MAC port. The user can define the connection and the size of the transmit and receive queues. The size is adjustable in units of 32 (by 2048 byte) packets. The external SDRAM can hold up to 8192 packets of data. The user must ensure that all the connection queues do no exceed this limit. The user also must ensure that the transmit and receive queues do not overlap each other. Unidirectional connections are not supported. When the user changes the queue sizes, the connection must be torn down and re-established. When a connection is disconnected all transmit and receive queues associated with the connection are flushed and a "1' is sourced towards the Serial transmit and the HDLC receiver. The clocks to the HDLC are sourced a "0". The user can also program high and low watermarks. If the queue size grows past the High watermark, an interrupt is generated if enabled. The registers of relevance are described in Table 9-3. The AR.TQSC1 size provides the size of the transmit queue for the connection. The high watermark will set a latched status bit. The latched status bit will clear when the register is read. The status bit is indicated by LI.TQCTLS.TQHTS. Interrupts can be enabled on the latched bit events by LI.TQTIE. A latched status bit (LI.TQCTLS.TQLTS) is also set when the queue crosses a low watermark. The Receive Queue functions in a similar manner. Note that the user must ensure that sizes and watermarks are set in accordance with the configuration speed of the Ethernet and Serial interfaces. The DS33R11 does not provide error indication if the user creates a connection and queue that overwrites data for another connection queue. The user must take care in setting the queue sizes and watermarks. The registers of relevance are AR.RQSC1and SU.QCRLS. Queue size should never be set to 0.
51 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver It is recommended that the user reset the queue pointers for the connection after disconnection. The pointers must be reset before a connection is made. If this disconnect/connect procedure is not followed, incorrect data may be transmitted. The proper procedure for setting up a connection follows: * * * * * Set up the queue sizes for both transmit and receive queue (AR.TQSC1 and AR.RQSC1). Set up the high/low thresholds and interrupt enables if desired (GL.TRQIE, LI.TQTIE, SU.QRIE). Reset all the pointers for the connection desired (GL.C1QPR). Set up the connections (GL.CON1). If a connection is disconnected, reset the queue pointers after the disconnection.
Table 9-3. Registers Related to Connections and Queues
REGISTER GL.CON1 AR.TQSC1 AR.RQSC1 GL.TRQIE GL.TRQIS LI.TQTIE LI.TQCTLS SU.QRIE SU.QCRLS GL.C1QPR FUNCTION Enables connection between the Ethernet Interface and the Serial Interface. Note that once connection is set up, then the queues and thresholds can be setup for that connection. Size for the Transmit Queue in Number of 32--2K packets. Size for the Receive Queue in Number of 32--2K packets. Interrupt enable for items related to the connections at the global level Interrupt enable status for items related to the connections at the global level Enables for the Transmit queue crossing high and low thresholds Latched status bits for connection high and low thresholds for the transmit queue. Enables for the receive queue crossing high and low thresholds Latched status bits for receive queue high and low thresholds. Resets the connection pointer.
9.12 Arbiter
The Arbiter manages the transport between the Ethernet port and the Serial port. It is responsible for queuing and dequeuing packets to a single external SDRAM. The arbiter handles requests from the HDLC and MAC to transfer data to and from the SDRAM.
52 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.13 Flow Control
Flow control may be required to ensure that data queues do not overflow and packets are not lost. The DS33R11 allows for optional flow control based on the queue high watermark or through host processor intervention. There are 2 basic mechanisms that are used for flow control: * * In half duplex mode, a jam sequence is sent that causes collisions at the far end. The collisions cause the transmitting node to reduce the rate of transmission. In full duplex mode, flow control is initiated by the receiving node sending a pause frame. The pause frame has a timer parameter that determines the pause timeout to be used by the transmitting node.
Note that the terms "transmit queue" and "receive queue" are with respect to the Ethernet Interface. The Receive Queue is the queue for the data that arrives on the MII/RMII interface, is processed by the MAC and stored in the SDRAM. Transmit queue is for data that arrives from the Serial port, is processed by the HDLC and stored in the SDRAM to be sent to the MAC transmitter. The following flow control options are possible: * Automatic flow control can be enabled in software mode with the SU.GCR.ATFLOW bit. Note that the user does not have control over SU.MACFCR.FCE and FCB bits if ATFLOW is set. The mechanism of sending pause or jam is dependent only on the receive queue high threshold. Manual flow control can be performed through software when SU.GCR.ATFLOW=0. The host processor must monitor the receive queues and generate pause frames (full duplex) and/or jam bytes through the SU.MACFCR.FCB, SU.GCR.JAME, and SU.MACFCR.FCE bits.
*
Note that in order to use flow control, the receive queue size (in AR.RQSC1) must be 02h or greater. The receive queue high threshold (in SU.RQHT) must be set to 01h or greater, but must be less than the queue size. If the high threshold is set to the same value as the queue size, automatic flow control will not be effective. The high threshold must always be set to less than the corresponding queue size. The following table provides all the options on flow control mechanism for DS33R11.
Table 9-4. Options for Flow Control
TYPE Configuration ATFLOW Bit JAME Bit FCB Bit (Pause) FCE Bit Pause Timer Half Duplex; Manual Flow Control 0 Controlled By User N/A Controlled By User N/A Half Duplex; Automatic Flow Control 1 Controlled Automatically N/A Controlled Automatically N/A MODE Full Duplex; Manual Flow Control 0 N/A Controlled by User Controlled By User Programmed by User Full Duplex; Automatic Flow Control 1 N/A Controlled Automatically Controlled Automatically Programmed by User
53 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.13.1 Full Duplex Flow Control
Automatic flow control is enabled by default. The host processor can disable this functionality with SU.GCR.ATFLOW. The flow control mechanism is governed by the high watermarks (SU.RQHT). The SU.RQLT low threshold can be used as indication that the network congestion is clearing up. The value of SU.RQLT does not affect the flow control. When the connection queue high threshold is exceeded the DS33R11 will send a pause frame with the timer value programmed by the user. See Table 9-6 for more information. It is recommended that 80 slots (80 by 64 bytes or 5120 bytes) be used as the standard timer value. The pause frame causes the distant transmitter to "pause for a time" before starting transmission again. The pause command has a multicast address 01-80-62-00-00-01. The high and low thresholds for the receive queue are configurable by the user but it is recommended that the high threshold be set approximately 96 packets from the maximum size of the queue and the low threshold 96 packets lower than the high threshold. The DS33R11 will send a pause frame as the queue has crossed the high threshold and a frame is received. Pause is sent every time a frame is received in the "high threshold state". Pause control will only take care of temporary congestion. Pause control does not take care of systems where the traffic throughput is too high for the queue sizes selected. If the flow control is not effective the receive queue will eventually overflow. This is indicated by SU.QCRLS.RQOVFL latched bit. If the receive queue is overflowed any new frames will not be received. The user has the option of not enabling automatic flow control. In this case the thresholds and corresponding interrupt mechanism to send pause frame by writing to flow control busy bit in the MAC flow control registers SU.MACFCR.FCB, SU.GCR.JAME, and SU.MACFCR. This allows the user to set not only the watermarks but also to decide when to send a pause frame or not based on watermark crossings. On the receive side the user has control over whether to respond to the pause frame sent by the distant end (PCF bit). Note that if automatic flow control is enabled the user cannot modify the FCE bit in the MAC flow control register. On the Transmit queue the user has the option of setting high and low thresholds and corresponding interrupts. There is no automatic flow control mechanism for data received from the Serial side waiting for transmission over the Ethernet interface during times of heavy Ethernet congestion.
54 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-3. Flow Control Using Pause Control Frame
8
Receive Queue Low Water Rx Data Receive Queue Growth Receive Queue High Water Mark Initiate Flow control
9.13.2 Half Duplex Flow Control
Half duplex flow control uses a jamming sequence to exert backpressure on the transmitting node. The receiving node jams the first 4 bytes of a packet that are received from the MAC in order to cause collisions at the distant end. In both 100Mbit/s and 10Mbit/s MII/RMII modes, 4 bytes are jammed upon reception of a new frame. Note that the jamming mechanism does not jam the current frame that is being received during the watermark crossing, but will wait to jam the next frame after the SU.RQHT bit is set. If the queue remains above the high threshold, received frames will continue to be jammed. This jam sequence is stopped when the queue falls below the high threshold.
9.13.3 Host-Managed Flow Control
Although automatic flow control is recommended, flow control by the host processor is also possible. By utilizing the high watermark interrupts, the host processor can manually issue pause frames or jam incoming packets to exert backpressure on the transmitting node. Pause frames can be initiated with SU.MACFCR.FCB bit. Jam sequences can be initiated be setting SU.GCR.JAME. The host can detect pause frames by monitoring SU.RFSB3.UF and SU.RFSB3.CF. Jammed frames will be indistinguishable from packet collisions.
55 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.14 Ethernet Interface Port
The Ethernet port interface allows for direct connection to an Ethernet PHY. The interface consists of a 10/100Mbit/s MII/RMII interface and an Ethernet MAC. In RMII operation, the interface contains seven signals with a reference clock of 50 MHz. In MII operation, the interface contains 17 signals and a clock reference of 25MHz. The DS33R11 can be configured to RMII or MII interface by the Hardware pin RMIIMIIS. The REF_CLKO output can be used to source the REF_CLK input. If the port is configured for MII in DCE mode, REF_CLK must be 25MHz. The DS33R11 will internally generate the TX_CLK and RX_CLK outputs (at 25MHz for 100Mbps, 2.5MHz for 10Mbps) required for DCE mode from the REF_CLK input. In MII mode with DTE operation, the TX_CLK and RX_CLK signals are generated by the PHY and are inputs to the DS33R11. For more information on clocking the Ethernet Interface, see Section 9.1. The data received from the MII or RMII interface is processed by the internal IEEE 802.3 complaint Ethernet MAC. The user can select the maximum frame size (up to 2016 bytes) that is received with the SU.RMFSRH and SU.RMFSRL registers. The maximum frame length (in bits) is the number specified in SU.RMFSRH and SU.RMFSRL multiplied by 8. Any programmed value greater than 2016 bytes will result in unpredictable behavior and should be avoided. The maximum frame size is shown in Figure 9-4. The length includes only destination address, source address, VLAN tag (2 bytes), type length field, data and CRC32. The frame size is different than the 802.3 "type length field." Frames from the Ethernet PHY or received from the packet processor are rejected if greater than the maximum frame size specified. Each Ethernet frame sent or received generates status bits (SU.TFSH and SU.TFSL and SU.RFSB0 to SU.RFSB3). These are real-time status registers and will change as each frame is sent or received. Hence they are useful to the user only when one frame is sent or received and the status is associated with the frame sent or received.
Figure 9-4. IEEE 802.3 Ethernet Frame
Preamble
SFD
Destination Adrs
Source Address
Type Lenght
Data
CRC32
7
1
6
6 Max Frame Length
2
46-1500
4
Encapsulated Frame
The distant end will normally reject the sent frames if jabber timeout, Loss of carrier, excessive deferral, late collisions, excessive collisions, under run, deferred or collision errors occur. Transmission of a frame under any of theses errors will generate a status bit in SU.TFSL, SU.TFSH. The DS33R11 provides user the option to automatically retransmit the frame if any of the errors have occurred through the bit settings in SU.TFRC. Deferred frames and heartbeat fail have separate resend control bits (SU.TFRC.TFBFCB and SU.TFRC.TPRHBC). If there is no carrier (indicated by the MAC Transmit Packet Status), the transmit queue (data from the Serial Interface to the SDRAM to Ethernet Interface) can be selectively flushed. This is controlled by SU.TFRC.NCFQ.
56 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver The MAC circuitry generates a frame status for every frame that is received. This real time status can be read by SU.RFSB0 to SU.RFSB3. Note the frame status is the "real time" status and hence the value will change as new frames are received. Hence the real time status reflects the status in time and may not correspond to the current received frame being processed. This is also true for the transmitted frames. Frames with errors are usually rejected by the DS33R11. The user has the option of accepting frames by settings in Receive Frame Rejection Control register (SU.RFRC). The user can program whether to reject or accept frames with the following errors: * * * * * * MII error asserted during the reception of the frame Dribbling bits occurred in the frame CRC error occurred Length error occurred--the length indicated by the frame length is inconsistent with the number of bytes received Control frame was received. The mode must be full duplex Unsupported control frame was received
Note that frames received that are runt frames or frames with collision will automatically be rejected.
Table 9-5. Registers Related to Setting the Ethernet Port
REGISTER SU.TFRC SU.TFSL and SU.TFSH SU.RFSB0 to 3 SU.RFRC SU.RMFSRH and SU.RMFSRL SU.MACCR FUNCTION This register determines if the current frame is retransmitted due to various transmit errors. These two registers provide the real-time status of the transmit frame. Only apply to the last frame transmitted. These registers provide the real-time status for the received frame. Only apply to the last frame received. This register provides settings for reception or rejection of frame based on errors detected by the MAC. The settings for this register provide the maximum size of frames to be accepted from the MII/RMII receive interface. This register provides configuration control for the MAC.
57 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.14.1 DTE and DCE Mode
The Ethernet MII/RMII port can be configured for DCE or DTE Mode. When the port is configured for the DTE Mode it can be connected to an Ethernet PHY. In DCE mode, the port can be connected to MII/RMII MAC devices other than an Ethernet PHY. The DTE/DCE connections for the DS33R11 in MII mode are shown in the following two figures. In DCE Mode, the DS33R11 transmitter is connected to an external receiver and DS33R11 receiver is connected to an external MAC transmitter. The selection of DTE or DCE mode is done by the hardware pin DCEDTES.
Figure 9-5. Configured as DTE Connected to an Ethernet PHY in MII Mode
DS33R11
Rx RXD[3:0]
Ethernet Phy RXD[3:0] Rx
DTE
RXDV RX_CLK RX_ERR RX_CRS
RXDV RX_CLK RX_ERR RX_CRS COL_DET TXD[3:0]
DCE
MAC
COL_DET TXD[3:0] Tx TX_CLK TX_EN MDIO MDC
Tx TX_CLK TX_EN MDIO MDC
58 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-6. DS33R11 Configured as a DCE in MII Mode
DS33Z11
DCE Rx RXD[3:0] RXDV RX_CLK RX_ERR RX_CRS MAC COL_DET TXD[3:0] TX_CLK TX_EN MDIO MDC TXD[3:0] TX_EN TX_CLK TX_ERR RX_CRS COL_DET RXD[3:0]
DTE Tx
MAC
Tx
Rx RX_CLK RXDV MDIO MDC
9.15 Ethernet MAC
Indirect addressing is required to access the MAC register settings. Writing to the MAC registers requires the SU.MACWD0-3 registers to be written with 4 bytes of data. The address for the write operation must be written to SU.MACAWL and SU.MACAWH. A write command is issued by writing a zero to SU.MACRWC.MCRW and a one to SU.MACRWC.MCS (MAC command status). MCS is cleared by the DS33R11 when the operation is complete. Reading from the MAC registers requires the SU.MACRADH and SU.MACRADL registers to be written with the address for the read operation. A read command is issued by writing a one to SU.MACRWC.MCRW and a zero to SU.MACRWC.MCS. SU.MACRWC.MCS is cleared by the DS33R11 when the operation is complete. After MCS is clear, valid data is available in SU.MACRD0-SU.MACRD3. Note that only one operation can be initiated (read or write) at one time. Data cannot be written or read from the MAC registers until the MCS bit has been cleared by the device. The MAC registers are detailed in the following table.
59 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 9-6. MAC Control Registers
ADDRESS 0000h-0003h 0014h-0017h 0018h-001Bh 001Ch-001Fh 0100h-0103h REGISTER SU.MACCR SU.MACMIIA SU.MACMIID SU.MACFCR SU.MMCCTRL DESCRIPTION MAC Control Register. This register is used for programming full duplex, half duplex, promiscuous mode, and back-off limit for half duplex. The transmit and receive enable bits must be set for the MAC to operate. MII Address Register. The address for PHY access through the MDIO interface. MII Data Register. Data to be written to (or read from) the PHY through MDIO interface. Flow Control Register MMC Control Register bit 0 for resetting the status counters
Table 9-7. MAC Status Registers
ADDRESS 0200h-0203h 0204h-0207h 0300h-0303h 0308h-030Bh 030Ch-030Fh 0334h-0337h 0338h-033Bh REGISTER SU.RxFrmCntr SU.RxFrmOKCtr SU.TxFrmCtr SU.TxBytesCtr SU.TxBytesOkCtr SU.TxFrmUndr SU.TxBdFrmsCtr DESCRIPTION All frames received counter Number of received frames that are good Number of frames transmitted Number of bytes transmitted Number of bytes transmitted with good frames Transmit FIFO underflow counter Transmit number of frames aborted
60 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.15.1 MII Mode Options
The Ethernet interface can be configured for MII operation by setting the hardware pin RMIIMIIS low. The MII interface consists of 17 pins. For instructions on clocking the Ethernet Interface while in MII mode, see Section 9.1. Diagrams of system connections for MII operation are shown in Figure 9-5 and Figure 9-6.
9.15.2 RMII Mode
The Ethernet interface can be configured for RMII operation by setting the hardware pin RMIIMIIS high. RMII interface operates synchronously from the external 50MHz reference (REF_CLK). Only seven signals are required. The following figure shows the RMII architecture. Note that DCE mode is not supported for RMII mode and RMII is valid only for full duplex operation.
Figure 9-7. RMII Interface
DS33R11 MAC
External PHY
TXD[1:0] TX_EN
CRS_DV RXD[1:0] REF_CLK
61 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.15.3 PHY MII Management Block and MDIO Interface
The MII Management Block allows for the host to control up to 32 PHYs, each with 32 registers. The MII block communicates with the external PHY using 2-wire serial interface composed of MDC (serial clock) and MDIO for data. The MDIO data is valid on the rising edge of the MDC clock. The Frame format for the MII Management Interface is shown Figure 9-8. The read/write control of the MII Management is accomplished through the indirect SU.MACMIIA MII Management Address Register and data is passed through the indirect SU.MACMIID Data Register. These indirect registers are accessed through the MAC Control Registers defined in Table 9-6. The MDC clock is internally generated and runs at 1.67MHz.
Figure 9-8. MII Management Frame
Opco de 2 bits 10 Turn Aroun d 2 bits ZZ
Preamble 32 bits READ 111...111
Start 2 bits 01
Phy Adrs 5 bits PHYA[4:0]
Phy Reg 5 bits PHYR[4:0]
Data 16 bits ZZZZZZZZZ
Idle 1 Bit Z
WRITE
111...111
01
01
PHYA[4:0]
PHYR[4:0]
10
PHYD[15:0]
Z
9.16
BERT in the Ethernet Mapper
The BERT in the Ethernet Mapper can be used for generation and detection of BERT patterns. The BERT is a software programmable test pattern generator and monitor capable of meeting most error performance requirements for digital transmission equipment. The following restrictions are related to the BERT: * * * * * The RDEN and TDEN are inputs that can be used to "gap" bits. BERT will transmit even when the device is set for X.86 mode and TDEN is configured as an output. The normal traffic flow is halted while the BERT is in operation. If the BERT is enabled for a Serial port, it will override the normal connection. If there is a connection overridden by the BERT, when BERT operation is terminated the normal operation is restored.
The transmit direction generates the programmable test pattern, and inserts the test pattern payload into the data stream. The receive direction extracts the test pattern payload from the receive data stream, and monitors the test pattern payload for the programmable test pattern.
BERT Features
* * * * PRBS and QRSS patterns of 2 -1, 2 -1 2 -1 and QRSS pattern support. Programmable repetitive pattern. The repetitive pattern length and pattern are programmable. n [length n = 1 to 32 and pattern = 0 to (2 - 1)]. 24-bit error count and 32-bit bit count registers. Programmable bit error insertion. Errors can be inserted individually.
9 15 23
62 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.16.1 Receive Data Interface
9.16.1.1 Receive Pattern Detection The Receive BERT receives only the payload data and synchronizes the receive pattern generator to the incoming pattern. The receive pattern generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or bit 1 to the most significant bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating n y polynomial x + x + 1), the feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is bit n. The values for n and y are individually programmable (1 to 32). The output of the receive pattern generator is the feedback. If QRSS is enabled, the feedback is an XOR of bits 17 and 20, and the output is forced to one if the next 14 bits are all zeros. QRSS is programmable (on or off). For PRBS and QRSS patterns, the feedback is forced to one if bits 1 through 31 are all zeros. Depending on the type of pattern programmed, pattern detection performs either PRBS synchronization or repetitive pattern synchronization.
9.16.1.2
PRBS Synchronization
PRBS synchronization synchronizes the receive pattern generator to the incoming PRBS or QRSS pattern. The receive pattern generator is synchronized by loading 32 data stream bits into the receive pattern generator, and then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match the incoming pattern. If at least is incoming bits in the current 64-bit window do not match the receive pattern generator, automatic pattern resynchronization is initiated. Automatic pattern resynchronization can be disabled.
Figure 9-9. PRBS Synchronization State Diagram
Sync
6o
err ors
f6 4b
out
w its
bi t sw ith
ors err ith
32
1 bit error
Verify
32 bits loaded
Load
63 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.16.2 Repetitive Pattern Synchronization
Repetitive pattern synchronization synchronizes the receive pattern generator to the incoming repetitive pattern. The receive pattern generator is synchronized by searching each incoming data stream bit position for the repetitive pattern, and then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match the incoming pattern. If at least sis incoming bits in the current 64-bit window do not match the receive PRBS pattern generator, automatic pattern resynchronization is initiated. Automatic pattern resynchronization can be disabled.
Figure 9-10. Repetitive Pattern Synchronization State Diagram
Sync
6o
err ors
f6 4b
out
w its
bi t sw ith
ors err ith
32
1 bit error
Verify
Pattern Matches
Match
9.16.3 Pattern Monitoring
Pattern monitoring monitors the incoming data stream for Out Of Synchronization (OOS) condition, bit errors, and counts the incoming bits. An OOS condition is declared when the synchronization state machine is not in the "Sync" state. An OOS condition is terminated when the synchronization state machine is in the "Sync" state. Bit errors are determined by comparing the incoming data stream bit to the receive pattern generator output. If they do not match, a bit error is declared, and the bit error and bit counts are incremented. If they match, only the bit count is incremented. The bit count and bit error count are not incremented when an OOS condition exists.
9.16.4 Pattern Generation
Pattern Generation generates the outgoing test pattern, and passes it onto Error Insertion. The transmit pattern generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or bit 1 to the most significant n y bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating polynomial x + x + 1), the feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is bit n. The values for n and y are individually programmable. The output of the receive pattern generator is the feedback. If QRSS is enabled, the feedback is an XOR of bits 17 and 20, and the output is forced to one if the next 14 bits are all zeros. QRSS is programmable (on or off). For PRBS and QRSS patterns, the feedback is forced to one if bits 1 through 31 are all zeros. When a new pattern is loaded, the pattern generator is loaded with a pattern value before pattern generation n starts. The pattern value is programmable (0 - 2 - 1). When PRBS and QRSS patterns are generated the seed value is all ones.
64 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver 9.16.4.1 Error Insertion
Error insertion inserts errors into the outgoing pattern data stream. Errors are inserted one at a time Single bit error insertion can be initiated from the microprocessor interface. If pattern inversion is enabled, the data stream is inverted before the overhead/stuff bits are inserted. Pattern inversion is programmable (on or off). 9.16.4.2 Performance Monitoring Update All counters stop counting at their maximum count. A counter register is updated by asserting (low to high transition) the performance monitoring update signal (PMU). During the counter register update process, the performance monitoring status signal (PMS) is de-asserted. The counter register update process consists of loading the counter register with the current count, resetting the counter, forcing the zero count status indication low for one clock cycle, and then asserting PMS. No events shall be missed during an update procedure.
9.17 Transmit Packet Processor
The Transmit Packet Processor accepts data from the Transmit FIFO, performs bit reordering, FCS processing, packet error insertion, stuffing, packet abort sequence insertion, inter-frame padding, and packet scrambling. The data output from the Transmit Packet Processor to the Transmit Serial Interface is a serial data stream (bit synchronous mode). HDLC processing can be disabled (clear channel enable). Disabling HDLC processing disables FCS processing, packet error insertion, stuffing, packet abort sequence insertion, and inter-frame padding. Only bit reordering and packet scrambling are not disabled. Bit reordering changes the bit order of each byte. If bit reordering is disabled, the outgoing 8-bit data stream DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output from the Transmit FIFO with the MSB in TFD[7] (or 15, 23, or 31) and the LSB in TFD[0] (or 8, 16, or 24) of the transmit FIFO data TFD[7:0] 15:8, 23:16, or 31:24). If bit reordering is enabled, the outgoing 8-bit data stream DT[1:8] is output from the Transmit FIFO with the MSB in TFD[0] and the LSB in TFD[7] of the transmit FIFO data TFD[7:0]. In bit synchronous mode, DT [1] is the first bit transmitted. FCS processing calculates an FCS and appends it to the packet. FCS calculation is a CRC-16 or CRC-32 16 12 5 calculation over the entire packet. The polynomial used for FCS-16 is x + x + x + 1. The polynomial used for 32 26 23 22 16 12 11 10 8 7 5 4 2 FCS-32 is x + x + x + x + x + x + x + x + x + x + x + x + x + x + 1. The FCS is inverted after calculation. The FCS type is programmable. If FCS append is enabled, the calculated FCS is appended to the packet. If FCS append is disabled, the packet is transmitted without an FCS. The FCS append mode is programmable. If packet processing is disabled, FCS processing is not performed. Packet error insertion inserts errors into the FCS bytes. A single FCS bit is corrupted in each errored packet. The FCS bit corrupted is changed from errored packet to errored packet. Error insertion can be controlled by a register or by the manual error insertion input (LI.TMEI.TMEI). The error insertion initiation type (register or input) is programmable. If a register controls error insertion, the number and frequency of the errors are programmable. If FCS append is disabled, packet error insertion will not be performed. If packet processing is disabled, packet error insertion is not performed. Stuffing inserts control data into the packet to prevent packet data from mimicking flags. A packet start indication is received, and stuffing is performed until, a packet end indication is received. Bit stuffing consists of inserting a '0' directly following any five contiguous '1's. If packet processing is disabled, stuffing is not performed. There is at least one flag plus a programmable number of additional flags between packets. The inter-frame fill can be flags or all '1's followed by a start flag. If the inter-frame fill is all '1's, the number of '1's between the end and start flags does not need to be an integer number of bytes, however, there must be at least 15 consecutive '1's between the end and start flags. The inter-frame padding type is programmable. If packet processing is disabled, inter-frame padding is not performed. Packet abort insertion inserts a packet abort sequences as necessary. If a packet abort indication is detected, a packet abort sequence is inserted and inter-frame padding is done until a packet start flag is detected. The abort sequence is FFh. If packet processing is disabled, packet abort insertion is not performed. The packet scrambler is a x + 1 scrambler that scrambles the entire packet data stream. The packet scrambler runs continuously, and is never reset. In bit synchronous mode, scrambling is performed one bit at a time. In byte synchronous mode, scrambling is performed 8 bits at a time. Packet scrambling is programmable. Once all packet processing has been completed serial data stream is passed on to the Transmit Serial Interface. 65 of 338
43
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.18 Receive Packet Processor
The Receive Packet Processor accepts data from the Receive Serial Interface performs packet descrambling, packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, FCS byte extraction, and bit reordering. The data coming from the Receive Serial Interface is a serial data stream. Packet processing can be disabled (clear channel enable). Disabling packet processing disables packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, and FCS byte extraction. Only packet descrambling and bit reordering are not disabled. The packet descrambler is a self-synchronous x + 1 descrambler that descrambles the entire packet data stream. Packet descrambling is programmable. The descrambler runs continuously, and is never reset. The descrambling is performed one bit at a time. Packet descrambling is programmable. If packet processing is disabled, the serial data stream is demultiplexed in to an 8-bit data stream before being passed on. If packet processing is disabled, a packet boundary is arbitrarily chosen and the data is divided into "packets" of programmable size (dependent on maximum packet size setting). These packets are then passed on to bit reordering with packet start and packet end indications. Data then bypasses packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, and FCS byte extraction. Packet delineation determines the packet boundary by identifying a packet start or end flag. Each time slot is checked for a flag sequence (7Eh). Once a flag is found, it is identified as a start/end flag and the packet boundary is set. The flag check is performed one bit at a time. If packet processing is disabled, packet delineation is not performed. Inter-frame fill filtering removes the inter-frame fill between packets. When a packet end flag is detected, all data is discarded until a packet start flag is detected. The inter-frame fill can be flags or all '1's. The number of '1's between flags does not need to be an integer number of bytes, and if at least 7 '1's are detected in the first 16 bits after a flag, all data after the flag is discarded until a start flag is detected. There may be only one flag between packets. When the inter-frame fill is flags, the flags may have a shared zero (011111101111110). If there is less than 16 bits between two flags, the data is discarded. If packet processing is disabled, inter-frame fill filtering is not performed. Packet abort detection searches for a packet abort sequence. Between a packet start flag and a packet end flag, if an abort sequence is detected, the packet is marked with an abort indication, the aborted packet count is incremented, and all subsequent data is discarded until a packet start flag is detected. The abort sequence is seven consecutive ones. If packet processing is disabled, packet abort detection is not performed. Destuffing removes the extra data inserted to prevent data from mimicking a flag or an abort sequence. A start flag is detected, a packet start is set, the flag is discarded, destuffing is performed until an end flag is detected, a packet end is set, and the flag is discarded. In bit synchronous mode, bit destuffing is performed. Bit destuffing consists of discarding any '0' that directly follows five contiguous '1's. After destuffing is completed, the serial bit stream is demultiplexed into an 8-bit parallel data stream and passed on with packet start, packet end, and packet abort indications. If there is less than eight bits in the last byte, an invalid packet flag is raised, the packet is tagged with an abort indication, and the packet size violation count is incremented. If packet processing is disabled, destuffing is not performed. Packet size checking checks each packet for a programmable maximum and programmable minimum size. As the packet data comes in, the total number of bytes is counted. If the packet length is below the minimum size limit, the packet is marked with an aborted indication, and the packet size violation count is incremented. If the packet length is above the maximum size limit, the packet is marked with an aborted indication, the packet size violation count is incremented, and all packet data is discarded until a packet start is received. The minimum and maximum lengths include the FCS bytes, and are determined after destuffing has occurred. If packet processing is disabled, packet size checking is not performed. FCS error monitoring checks the FCS and aborts errored packets. If an FCS error is detected, the FCS errored packet count is incremented and the packet is marked with an aborted indication. If an FCS error is not detected, the receive packet count is incremented. The FCS type (16-bit or 32-bit) is programmable. If FCS processing or packet processing is disabled, FCS error monitoring is not performed. FCS byte extraction discards the FCS bytes. If FCS extraction is enabled, the FCS bytes are extracted from the packet and discarded. If FCS extraction is disabled, the FCS bytes are stored in the receive FIFO with the packet. If FCS processing or packet processing is disabled, FCS byte extraction is not performed. Bit reordering changes the bit order of each byte. If bit reordering is disabled, the incoming 8-bit data stream DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output to the Receive FIFO with the MSB in RFD[7] 66 of 338
43
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver (or 15, 23, or 31) and the LSB in RFD[0] (or 8, 16, or 24) of the receive FIFO data RFD[7:0] (or 15:8, 23:16, or 31:24). If bit reordering is enabled, the incoming 8-bit data stream DT[1:8] is output to the Receive FIFO with the MSB in RFD[0] and the LSB in RFD[7] of the receive FIFO data RFD[7:0]. DT[1] is the first bit received from the incoming data stream. Once all of the packet processing has been completed, The 8-bit parallel data stream is demultiplexed into a 32-bit parallel data stream. The Receive FIFO data is passed on to the Receive FIFO with packet start, packet end, packet abort, and modulus indications. At a packet end, the 32-bit word may contain 1, 2, 3, or 4 bytes of data depending on the number of bytes in the packet. The modulus indications indicate the number of bytes in the last data word of the packet.
Figure 9-11. HDLC Encapsulation of MAC Frame
Number of Bytes Flag(0x7E) Destination Adrs(DA) Source Adrs(SA) Length/Type MAC Client Data 1 6 6 2 46-1500
PAD FCS for MAC FCS for HDLC Flag(0x7E) 4 0/2/4
MSB
LSB
67 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.19 X.86 Encoding and Decoding
X.86 protocol provides a method for encapsulating Ethernet Frame onto LAPS. LAPS provides HDLC type framing structure for encapsulation of Ethernet frames. LAPS encapsulated frames can be used to send data onto a SONET/SDH network. The DS33R11 expects a byte synchronization signal to provide the byte boundary for the X.86 receiver. This is provided by the RBSYNC pin. The functional timing is shown in Figure 12-4. The X.86 transmitter provides a byte boundary indicator with the signal TBSYNC. The functional timing is shown in Figure 12-3.
Figure 9-12. LAPS Encoding of MAC Frames Concept
IEEE 802.3 MAC Frame
LAPS
Rate Adaption
SDH
68 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-13. X.86 Encapsulation of the MAC frame
Number of Bytes Flag(0x7E) Address(0x04) Control(0x03) 1st Octect of SAPI(0xfe) 2nd Octect of SAPI(0x01) Destination Adrs(DA) Source Adrs(SA) Length/Type MAC Client Data 1 1 1 1 1 6 6 2 46-1500
PAD FCS for MAC FCS for LAPS Flag(0x7E) 4 4
MSB
LSB
The DS33R11 will encode the MAC Frame with the LAPS encapsulation on a complete serial stream if configured for X.86 mode in the register LI.TX86E. The DS33R11 provides the following functions: * * * Control Registers for Address, Control, SAPIH, SAPIL. 32 bit FCS enabled. 43 Programmable X +1 scrambling.
The sequence of processing performed by the receiver is as follows: * * * * * * * Programmable octets X +1 descrambling. Detect the Start Flag (7E). Remove Rate adaptation octets 7d, dd. Perform transparency-processing 7d, 5e is converted to 7e and 7d, 5d is converted to 7d. Check for a valid Address, Control and SAPI fields (LI.TRX86A to LI.TRX86SAPIL). Perform FCS checking. Detect the closing flag.
43
69 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver The X86 received frame is aborted if: * * * * * If 7d,7E is detected. This is an abort packet sequence in X.86. Invalid FCS is detected. The received frame has less than 6 octets. Control, SAPI and address field are mismatched to the programmed value. Octet 7d and octet other than 5d,5e,7e or dd is detected.
For the transmitter if X.86 is enabled the sequence of processing is as follows: * * * * * Construct frame including start flag, SAPI, Control and MAC frame. Calculate FCS. Perform transparency processing - 7E is translated to 7D5E, 7D is translated to 7D5D. Append the end flag(7E). 43 Scramble the sequence X +1.
Note that the serial transmit and receive registers apply to the X.86 implementations with specific exceptions. The exceptions are outlined in the serial interface transmit and receive register sections.
70 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.20 Committed Information Rate Controller
The DS33R11 provides a CIR provisioning facility. The CIR can be used restricts the transport of received MAC data to a programmable rate. The CIR location is shown in the Figure 6-1. The CIR will restrict the data flow from the Receive MAC to Transmit HDLC. This can be used for provisioning and billing functions towards the WAN. The user must set the CIR register to control the amount of data throughput from the MAC to HDLC transmit. The CIR register is in granularity of 500kbit/s with a range of 0 to 52Mbit/s. The operation of the CIR is as follows: * * The CIR block counts the credits that are accumulated at the end of every 125ms. If data is received and stored in the SDRAM to be sent to the Serial Interface, the interface will request the data if there is a positive credit balance. If the credit balance is negative, transmit interface does not request data. New credit balance is calculated credit balance = old credit balance - frame size in bytes after the frame is sent. The credit balance is incremented every 125ms by CIR/8. Credit balances not used in 250ms are reset to 0. The maximum value of CIR can not exceed the transmit line rate. If the data rate received from the Ethernet interface is higher than the CIR, the receive queue buffers will fill and the high threshold water mark will invoke flow control to reduce the incoming traffic rate. The CIR function is only available for software mode of operation only. CIR function is only available in data received at the Ethernet Interface to be sent to WAN. There is not CIR functionality for data arriving from the WAN to be sent to the Ethernet Interface. Negative credits are not allowed, if there is not a credit balance, no frames are sent until there is a credit balance again.
* * * * * * * *
71 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10 INTEGRATED T1/E1/J1 TRANSCEIVER
10.1 T1/E1/J1 Clocks
Figure 10-1 shows the clock map of the T1/E1 transceiver. The routing for the transmit and receive clocks are shown for the various loopback modes and jitter attenuator positions. Although there is only one jitter attenuator, which can be placed in the receive or transmit path, two are shown for simplification and clarity.
Figure 10-1. T1/E1/J1 Clock Map
MCLK TSYSCLK
MCLKS = 0 MCLKS = 1
PRE-SCALER 2.048 TO 1.544 SYNTHESIZER
TR.LIC4.MPS0 TR.LIC4.MPS1 TR.LIC2.3
DJA = 1
8 x PLL
LOCAL LOOPBACK RCL = 1 JITTER ATTENUATOR SEE TR.LIC1 REGISTER JAS = 0 AND DJA = 0 DJA = 0 REMOTE LOOPBACK FRAMER LOOPBACK PAYLOAD LOOPBACK (SEE NOTES)
8XCLK
LLB = 0
RXCLK
RCL = 0 LLB = 1
LTCA
FLB = 0
BPCLK SYNTH
BPCLK RCLK
TO LIU TXCLK
JAS = 0 OR DJA = 1
JAS = 1 OR DJA = 1 RLB = 1
RECEIVE FRAMER
FLB = 1
PLB = 1
LTCA
JAS = 1 AND DJA = 0 RLB = 0
TRANSMIT FORMATTER
PLB = 0
TCLKT MUX
A B
C
TCLKT
The TCLKT MUX is dependent on the state of the TCSS0 and TCSS1 bits in the TR.CCR1 register and the state of the TCLKT pin.
72 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 10-1. T1/E1/J1 Transmit Clock Source
TCSS1 0 0 1 1 TCSS0 0 1 0 1 TRANSMIT CLOCK SOURCE The TCLKT pin (C) is always the source of transmit clock. Switch to the recovered clock (B) when the signal at the TCLKT pin fails to transition after one channel time. Use the scaled signal (A) derived from MCLK as the transmit clock. The TCLKT pin is ignored. Use the recovered clock (B) as the transmit clock. The TCLKT pin is ignored.
10.2 Per-Channel Operation
Some of the features described in the data sheet that operate on a per-channel basis use a special method for channel selection. There are five registers involved: per-channel pointer register (TR.PCPR) and per-channel data registers 1-4 (TR.PCDR1-4). The user selects which function or functions are to be applied on a per-channel basis by setting the appropriate bit(s) in the TR.PCPR register. The user then writes to the TR.PCDR registers to select the channels for that function. The following is an example of mapping the transmit and receive BERT function to channels 9-12, 20, and 21. Write Write Write Write Write 11h 00h 0fh 18h 00h to to to to to TR.PCPR TR.PCDR1 TR.PCDR2 TR.PCDR3 TR.PCDR4
The user may write to the TR.PCDR1-4 with multiple functions in the TR.PCPR register selected, but can only read the values from the TR.PCDR1-4 registers for a single function at a time. More information about how to use these per-channel features can be found in the TR.PCPR register.
10.3 T1/E1/J1 Transceiver Interrupts
Various alarms, conditions, and events in the T1/E1/J1 transceiver can cause interrupts. For simplicity, these are all referred to as events in this explanation. All status registers can be programmed to produce interrupts. Each status register has an associated interrupt mask register. For example, TR.SR1 (status register 1) has an interrupt control register called TR.IMR1 (interrupt mask register 1). Status registers are the only sources of interrupts in the device. On power-up, all writeable registers of the T1/E1/J1 transceiver are automatically cleared. Since bits in the TR.IMRx registers have to be set = 1 to allow a particular event to cause an interrupt, no interrupts can occur until the host selects which events are to product interrupts. Since there are potentially many sources of interrupts on the device, several features are available to help sort out and identify which event is causing an interrupt. When an interrupt occurs, the host should first read the TR.IIR1 and TR.IIR2 registers (interrupt information registers) to identify which status register (or registers) is producing the interrupt. Once that is determined, the individual status register or registers can be examined to determine the exact source. Once an interrupt has occurred, the interrupt handler routine should set the INTDIS bit (TR.CCR3.6) to stop further activity on the interrupt pin. After all interrupts have been determined and processed, the interrupt hander routine should re-enable interrupts by setting the INTDIS bit = 0. Note that the integrated Ethernet Mapper also generates interrupts, as discussed in Section 9.6.
73 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.4 T1 Framer/Formatter Control and Status
The T1 framer portion of the transceiver is configured through a set of nine control registers. Typically, the control registers are only accessed when the system is first powered up. Once the transceiver has been initialized, the control registers only need to be accessed when there is a change in the system configuration. There are two receive control registers (TR.T1RCR1 and TR.T1RCR2), two transmit control registers (TR.T1TCR1 and TR.T1TCR2), and a common control register (TR.T1CCR1). Each of these registers is described in this section.
10.4.1 T1 Transmit Transparency
The software signaling insertion-enable registers, TR.SSIE1- TR.SSIE4, can be used to select signaling insertion from the transmit signaling registers, TS1-TS12, on a per-channel basis. Setting a bit in the SSIEx register allows signaling data to be sourced from the signaling registers for that channel. In transparent mode, bit 7 stuffing and/or robbed-bit signaling is prevented from overwriting the data in the channels. If a DS0 is programmed to be clear, no robbed-bit signaling is inserted nor does the channel have bit 7 stuffing performed. However, in the D4 framing mode, bit 2 is overwritten by a 0 when a Yellow Alarm is transmitted. Also, the user has the option to globally override the TR.SSIEx registers from determining which channels are to have bit 7 stuffing performed. If the TR.T1TCR1.3 and TR.T1TCR2.0 bits are set to 1, then all 24 T1 channels have bit 7 stuffing performed on them, regardless of how the TR.SSIEx registers are programmed. In this manner, the TR.SSIEx registers are only affecting the channels that are to have robbed-bit signaling inserted into them.
10.4.2 AIS-CI and RAI-CI Generation and Detection
The device can transmit and detect the RAI-CI and AIS-CI codes in T1 mode. These codes are compatible with and do not interfere with the standard RAI (Yellow) and AIS (Blue) alarms. These codes are defined in ANSI T1.403. The AIS-CI code (alarm indication signal-customer installation) is the same for both ESF and D4 operation. Setting the TAIS-CI bit in the TR.T1CCR1 register and the TBL bit in the TR.T1TCR1 register causes the device to transmit the AIS-CI code. The RAIS-CI status bit in the TR.SR4 register indicates the reception of an AIS-CI signal. The RAI-CI (remote alarm indication-customer installation) code for T1 ESF operation is a special form of the ESF Yellow Alarm (an unscheduled message). Setting the RAIS-CI bit in the TR.T1CCR1 register causes the device to transmit the RAI-CI code. The RAI-CI code causes a standard Yellow Alarm to be detected by the receiver. When the host processor detects a Yellow Alarm, it can then test the alarm for the RAI-CI state by checking the BOC detector for the RAI-CI flag. That flag is a 011111 code in the 6-bit BOC message. The RAI-CI code for T1 D4 operation is a 10001011 flag in all 24 time slots. To transmit the RAI-CI code the host sets all 24 channels to idle with a 10001011 idle code. Since this code meets the requirements for a standard T1 D4 Yellow Alarm, the host can use the receive channel monitor function to detect the 100001011 code whenever a standard Yellow Alarm is detected.
74 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.4.3 T1 Receive-Side Digital-Milliwatt Code Generation
Receive-side digital-milliwatt code generation involves using the receive digital-milliwatt registers (TR.T1RDMR1/2/3) to determine which of the 24 T1 channels of the T1 line going to the backplane should be overwritten with a digital-milliwatt pattern. The digital-milliwatt code is an 8-byte repeating pattern that represents a 1kHz sine wave (1E/0B/0B/1E/9E/8B/8B/9E). Each bit in the TR.T1RDMRx registers represents a particular channel. If a bit is set to a 1, then the receive data in that channel is replaced with the digital-milliwatt code. If a bit is set to 0, no replacement occurs.
Table 10-2. T1 Alarm Criteria
ALARM Blue Alarm (AIS) (Note 1) Yellow Alarm (RAI) D4 Bit 2 Mode (TR.T1RCR2.0 = 0) D4 12th F-Bit Mode (TR.T1RCR2.0 = 1; this mode is also referred to as the "Japanese Yellow Alarm") ESF Mode SET CRITERIA When over a 3ms window, five or fewer 0s are received When bit 2 of 256 consecutive channels is set to 0 for at least 254 occurrences When the 12th framing bit is set to 1 for two consecutive occurrences CLEAR CRITERIA When over a 3ms window, six or more 0s are received When bit 2 of 256 consecutive channels is set to 0 for fewer than 254 occurrences When the 12th framing bit is set to 0 for two consecutive occurrences
When 16 consecutive patterns of 00FF appear in the FDL When 192 consecutive 0s are received
When 14 or fewer patterns of 00FF hex out of 16 possible appear in the FDL When 14 or more 1s out of 112 possible bit positions are received
Red Alarm (LRCL) (Also referred to as loss of signal)
Note 1: The definition of Blue Alarm (or AIS) is an unframed all-ones signal. Blue Alarm detectors should be able to operate properly in the presence of a 10E-3 error rate and they should not falsely trigger on a framed all-1s signal. Blue Alarm criteria in the device has been set to achieve this performance. It is recommended that the RBL bit be qualified with the RLOS bit. Note 2: ANSI specifications use a different nomenclature than this document. The following terms are equivalent: RBL = AIS RCL = LOS RLOS = LOF RYEL = RAI
75 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.5 E1 Framer/Formatter Control and Status
The E1 framer portion of the transceiver is configured by a set of four control registers. Typically, the control registers are only accessed when the system is first powered up. Once the device has been initialized, the control registers need only to be accessed when there is a change in the system configuration. There are two receive control registers (TR.E1RCR1 and TR.E1RCR2) and two transmit control registers (TR.E1TCR1 and TR.E1TCR2). There are also four status and information registers. Each of these eight registers is described in this section.
Table 10-3. E1 Sync/Resync Criteria
FRAME OR MULTIFRAME LEVEL SYNC CRITERIA RESYNC CRITERIA Three consecutive incorrect FAS received FAS FAS present in frame N and N + 2; FAS not present in frame N + 1 Two valid MF alignment words found within 8ms Valid MF alignment word found and previous time slot 16 contains code other than all 0s Alternate: (TR.E1RCR1.2 = 1) The above criteria is met or three consecutive incorrect bit 2 of non-FAS received 915 or more CRC4 codewords out of 1000 received in error Two consecutive MF alignment words received in error G.706 4.1.1 4.1.2 G.706 4.2 and 4.3.2 G.732 5.2 ITU SPEC.
CRC4 CAS
76 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.5.1 Automatic Alarm Generation
The device can be programmed to automatically transmit AIS or remote alarm. When automatic AIS generation is enabled (TR.E1TCR2.1 = 1), the device monitors the receive-side framer to determine if any of the following conditions are present: loss-of-receive frame synchronization, AIS alarm (all ones) reception, or loss-of-receive carrier (or signal). The framer forces either an AIS or remote alarm if any one or more of these conditions is present. When automatic RAI generation is enabled (TR.E1TCR2.0 = 1), the framer monitors the receive side to determine if any of the following conditions are present: loss-of-receive-frame synchronization, AIS alarm (all ones) reception, loss-of-receive carrier (or signal), or if CRC4 multiframe synchronization cannot be found within 128ms of FAS synchronization (if CRC4 is enabled). If any one or more of these conditions is present, then the framer transmits an RAI alarm. RAI generation conforms to ETS 300 011 specifications and a constant remote alarm is transmitted if the device cannot find CRC4 multiframe synchronization within 400ms as per G.706. Note: It is an invalid state to have both automatic AIS generation and automatic remote alarm generation enabled at the same time.
Table 10-4. E1 Alarm Criteria
ALARM RLOS RCL RRA RUA1 RDMA V52LNK SET CRITERIA An RLOS condition exists on power-up prior to initial synchronization, when a resync criteria has been met, or when a manual resync has been initiated by TR.E1RCR1.0 255 or 2048 consecutive 0s received as determined by TR.E1RCR2.0 Bit 3 of nonalign frame set to 1 for three consecutive occasions Fewer than three 0s in two frames (512 bits) Bit 6 of time slot 16 in frame 0 has been set for two consecutive multiframes Two out of three Sa7 bits are 0 CLEAR CRITERIA ITU SPECIFICATION
At least 32 1s in 255-bit times are received Bit 3 of nonalign frame set to 0 for three consecutive occasions More than two 0s in two frames (512 bits)
G.775/G.962 O.162 2.1.4 O.162 1.6.1.2
G.965
10.6 Per-Channel Loopback
The per-channel loopback registers (PCLRs) determine which channels (if any) from the backplane should be replaced with the data from the receive side or, i.e., off of the T1 or E1 line. If this loopback is enabled, then transmit and receive clocks and frame syncs must be synchronized. One method to accomplish this is to connect RCLKO to TCLKT and RFSYNC to TSYNC. There are no restrictions on which channels can be looped back or on how many channels can be looped back. Each of the bit positions in the per-channel loopback registers (TR.PCLR1/ TR.PCLR2/ TR.PCLR3/ TR.PCLR4) represents a DS0 channel in the outgoing frame. When these bits are set to a 1, data from the corresponding receive channel replaces the data on TSERI for that channel.
77 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.7 Error Counters
The transceiver contains four counters that are used to accumulate line-coding errors, path errors, and synchronization errors. Counter update options include one-second boundaries, 42ms (T1 mode only), 62ms (E1 mode only), or manual. See Error-Counter Configuration Register (TR.ERCNT). When updated automatically, the user can use the interrupt from the timer to determine when to read these registers. All four counters saturate at their respective maximum counts, and they do not roll over. Note: Only the line-code violation count register has the potential to overflow, but the bit error would have to exceed 10E-2 before this would occur.
10.7.1 Line-Code Violation Counter (TR.LCVCR)
In T1 mode, code violations are defined as bipolar violations (BPVs) or excessive 0s. If the B8ZS mode is set for the receive side, then B8ZS codewords are not counted. This counter is always enabled; it is not disabled during receive loss-of-synchronization (RLOS = 1) conditions. Table 10-5 shows what the LCVCRs count.
Table 10-5 T1 Line Code Violation Counting Options
COUNT EXCESSIVE ZEROS? (TR.ERCNT.0) No Yes No Yes B8ZS ENABLED? (TR.T1RCR2.5) No No Yes Yes COUNTED IN THE LCVCRs BPVs BPVs + 16 consecutive 0s BPVs (B8ZS codewords not counted) BPVs + 8 consecutive 0s
In E1 mode, either bipolar violations or code violations can be counted. Bipolar violations are defined as consecutive marks of the same polarity. In this mode, if the HDB3 mode is set for the receive side, then HDB3 codewords are not counted as BPVs. If TR.ERCNT.3 is set, then the LVC counts code violations as defined in ITU O.161. Code violations are defined as consecutive bipolar violations of the same polarity. In most applications, the framer should be programmed to count BPVs when receiving AMI code and to count CVs when receiving HDB3 code. This counter increments at all times and is not disabled by loss-of-sync conditions. The counter saturates at -2 65,535 and does not roll over. The bit-error rate on an E1 line would have to be greater than 10 before the VCR would saturate (Table 10-6).
Table 10-6. E1 Line-Code Violation Counting Options
E1 CODE VIOLATION SELECT (TR.ERCNT.3) COUNTED IN THE LCVCRs
0 1
BPVs CVs
78 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.7.2 Path Code Violation Count Register (TR.PCVCR)
In T1 mode, the path code violation count register records Ft, Fs, or CRC6 errors in T1 frames. When the receive side of a framer is set to operate in the T1 ESF framing mode, TR.PCVCR records errors in the CRC6 codewords. When set to operate in the T1 D4 framing mode, TR.PCVCR counts errors in the Ft framing bit position. Through the TR.ERCNT.2 bit, a framer can be programmed to also report errors in the Fs framing bit position. The TR.PCVCR is disabled during receive loss-of-synchronization (RLOS = 1) conditions. Table 10-7 shows what errors the TR.PCVCR counts.
Table 10-7. T1 Path Code Violation Counting Arrangements
FRAMING MODE D4 D4 ESF COUNT Fs ERRORS? No Yes Don't Care COUNTED IN THE PCVCRs Errors in the Ft pattern Errors in both the Ft and Fs patterns Errors in the CRC6 codewords
In E1 mode, the path code violation-count register records CRC4 errors. Since the maximum CRC4 count in a onesecond period is 1000, this counter cannot saturate. The counter is disabled during loss-of-sync at either the FAS or CRC4 level; it continues to count if loss-of-multiframe sync occurs at the CAS level. Path code violation-count register 1 (TR.PCVCR1) is the most significant word and TR.PCVCR2 is the least significant word of a 16-bit counter that records path violations (PVs).
79 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.7.3 Frames Out-of-Sync Count Register (TR.FOSCR)
In T1 mode, TR.FOSCR is used to count the number of multiframes that the receive synchronizer is out of sync. This number is useful in ESF applications needing to measure the parameters loss-of-frame count (LOFC) and ESF error events as described in AT&T publication TR54016. When TR.FOSCR is operated in this mode, it is not disabled during receive loss-of-synchronization (RLOS = 1) conditions. TR.FOSCR has an alternate operating mode whereby it counts either errors in the Ft framing pattern (in the D4 mode) or errors in the FPS framing pattern (in the ESF mode). When TR.FOSCR is operated in this mode, it is disabled during receive loss-of-synchronization (RLOS = 1) conditions. Table 10-8 shows what the FOSCR is capable of counting.
Table 10-8. T1 Frames Out-of-Sync Counting Arrangements
FRAMING MODE (TR.T1RCR1.3) D4 D4 ESF ESF COUNT MOS OR F-BIT ERRORS (TR.ERCNT.1) MOS F-Bit MOS F-Bit COUNTED IN THE FOSCRs Number of multiframes out-of-sync Errors in the Ft pattern Number of multiframes out-of-sync Errors in the FPS pattern
In E1 mode, TR.FOSCR counts word errors in the FAS in time slot 0. This counter is disabled when RLOS is high. FAS errors are not counted when the framer is searching for FAS alignment and/or synchronization at either the CAS or CRC4 multiframe level. Since the maximum FAS word error count in a one-second period is 4000, this counter cannot saturate. The frames out-of-sync count register 1 (TR.FOSCR1) is the most significant word and TR.FOSCR2 is the least significant word of a 16-bit counter that records frames out-of-sync.
10.7.4 E-Bit Counter (TR.EBCR)
This counter is only available in E1 mode. E-bit count register 1 (TR.EBCR1) is the most significant word and TR.EBCR2 is the least significant word of a 16-bit counter that records far-end block errors (FEBE) as reported in the first bit of frames 13 and 15 on E1 lines running with CRC4 multiframe. These count registers increment once each time the received E-bit is set to 0. Since the maximum E-bit count in a one-second period is 1000, this counter cannot saturate. The counter is disabled during loss-of-sync at either the FAS or CRC4 level; it continues to count if loss-of-multiframe sync occurs at the CAS level.
80 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.8 DS0 Monitoring Function
The transceiver has the ability to monitor one DS0 64kbps channel in the transmit direction and one DS0 channel in the receive direction at the same time. In the transmit direction, the user determines which channel is to be monitored by properly setting the TCM0 to TCM4 bits in the TR.TDS0SEL register. In the receive direction, the RCM0 to RCM4 bits in the TR.RDS0SEL register need to be properly set. The DS0 channel pointed to by the TCM0 to TCM4 bits appear in the transmit DS0 monitor (TR.TDS0M) register. The DS0 channel pointed to by the RCM0 to RCM4 bits appear in the receive DS0 (TR.RDS0M) register. The TCM4 to TCM0 and RCM4 to RCM0 bits should be programmed with the decimal decode of the appropriate T1or E1 channel. T1 channels 1 through 24 map to register values 0 through 23. E1 channels 1 through 32 map to register values 0 through 31. For example, if DS0 channel 6 in the transmit direction and DS0 channel 15 in the receive direction needed to be monitored, then the following values would be programmed into TR.TDS0SEL and TR.RDS0SEL: TCM4 = 0 TCM3 = 0 TCM2 = 1 TCM1 = 0 TCM0 = 1 RCM4 = 0 RCM3 = 1 RCM2 = 1 RCM1 = 1 RCM0 = 0
81 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.9 Signaling Operation
There are two methods to access receive signaling data and provide transmit signaling data, processor-based (software-based) or hardware-based. Processor-based refers to access through the transmit and receive signaling registers RS1-RS16 and TS1-TS16. Hardware-based refers to the TSIG and RSIG pins. Both methods can be used simultaneously.
Figure 10-2. Simplified Diagram of Receive Signaling Path
PER-CHANNEL CONTROL T1/E1 DATA STREAM
SIGNALING EXTRACTION ALL-ONES
RSERO
RECEIVE SIGNALING REGISTERS CHANGE-OF-STATE INDICATION REGISTERS
REINSERTION CONTROL SIGNALING BUFFERS
RSYNC RSIG
10.9.1 Processor-Based Receive Signaling
The robbed-bit signaling (T1) or TS16 CAS signaling (E1) is sampled in the receive data stream and copied into the receive signaling registers, RS1-RS16. In T1 mode, only RS1-RS12 are used. The signaling information in these registers is always updated on multiframe boundaries. This function is always enabled. 10.9.1.1 Change-of-State To avoid constant monitoring of the receive signaling registers, the transceiver can be programmed to alert the host when any specific channel or channels undergo a change of their signaling state. TR.RSCSE1 - TR.RSCSE4 for E1 and TR.RSCSE1 - TR.RSCSE3 for T1 are used to select which channels can cause a change-of-state indication. The change-of-state is indicated in status register 5 (TR.SR1.5). If signaling integration (TR.CCR1.5) is enabled, then the new signaling state must be constant for three multiframes before a change-of-state is indicated. The user can enable the INT pin to toggle low upon detection of a change in signaling by setting the TR.IMR1.5 bit. The signaling integration mode is global and cannot be enabled on a channel-by-channel basis. The user can identity which channels have undergone a signaling change-of-state by reading the TR.RSINFO1- TR.RSINFO4 registers. The information from these registers inform the user which TR.RSx register to read for the new signaling data. All changes are indicated in the TR.RSINFO1 - TR.RSINFO4 registers regardless of the TR.RSCSE1 - TR.RSCSE4 registers.
82 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.9.2 Hardware-Based Receive Signaling
In hardware-based signaling the signaling data can be obtained from the RSERO pin or the RSIG pin. RSIG is a signaling PCM stream output on a channel-by-channel basis from the signaling buffer. The signaling data, T1 robbed bit or E1 TS16, is still present in the original data stream at RSERO. The signaling buffer provides signaling data to the RSIG pin and also allows signaling data to be reinserted into the original data stream in a different alignment that is determined by a multiframe signal from the RSYNC pin. In this mode, the receive elastic store can be enabled or disabled. If the receive elastic store is enabled, then the backplane clock (RSYSCLK) can be either 1.544MHz or 2.048MHz. In the ESF framing mode, the ABCD signaling bits are output on RSIG in the lower nibble of each channel. The RSIG data is updated once a multiframe (3ms) unless a freeze is in effect. In the D4 framing mode, the AB signaling bits are output twice on RSIG in the lower nibble of each channel. Hence, bits 5 and 6 contain the same data as bits 7 and 8, respectively, in each channel. The RSIG data is updated once a multiframe (1.5ms) unless a freeze is in effect. See the timing diagrams in Section 12 for some examples. 10.9.2.1 Receive Signaling Reinsertion at RSERO In this mode, the user provides a multiframe sync at the RSYNC pin and the signaling data is reinserted based on this alignment. In T1 mode, this results in two copies of the signaling data in the RSERO data stream, the original signaling data and the realigned data. This is of little consequence in voice channels. Reinsertion can be avoided in data channels since this feature is activated on a per-channel basis. In this mode, the elastic store must be enabled; however, the backplane clock can be either 1.544MHz or 2.048MHz. Signaling reinsertion can be enabled on a per-channel basis by setting the RSRCS bit high in the TR.PCPR register. The channels that will have signaling reinserted are selected by writing to the TR.PCDR1 - TR.PCDR3 registers for T1 mode and TR.PCDR1 - TR.PCDR4 registers for E1 mode. In E1 mode, the user generally selects all channels or none for reinsertion. In E1 mode, signaling reinsertion on all channels can be enabled with a single bit, TR.SIGCR.7 (GRSRE). This bit allows the user to reinsert all signaling channels without having to program all channels through the per-channel function. 10.9.2.2 Force Receive Signaling All Ones In T1 mode, the user can, on a per-channel basis, force the robbed-bit signaling bit positions to a 1 by using the per-channel register (Section 10.2). The user sets the BTCS bit in the TR.PCPR register. The channels that will be forced to 1 are selected by writing to the TR.PCDR1 - TR.PCDR3 registers. 10.9.2.3 Receive Signaling Freeze The signaling data in the four multiframe signaling buffers is frozen in a known good state upon either a loss of synchronization (OOF event), carrier loss, or frame slip. This action meets the requirements of BellCore TR-TSY- 000170 for signaling freezing. To allow this freeze action to occur, the RFE control bit (TR.SIGCR.4) should be set high. The user can force a freeze by setting the RFF control bit (TR.SIGCR.3) high. The RSIGF output pin provides a hardware indication that a freeze is in effect. The four-multiframe buffer provides a three-multiframe delay in the signaling bits provided at the RSIG pin (and at the RSERO pin if receive signaling reinsertion is enabled). When freezing is enabled (RFE = 1), the signaling data is held in the last-known good state until the corrupting error condition subsides. When the error condition subsides, the signaling data is held in the old state for at least an additional 9ms (or 4.5ms in D4 framing mode) before updating with new signaling data.
83 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-3. Simplified Diagram of Transmit Signaling Path
TRANSMIT SIGNALING REGISTERS 1 0 T1/E1 DATA STREAM 0 1 B7 TR.T1TCR1.4 PER-CHANNEL CONTROL TR.SSIE1 TR.SSIE4 ONLY APPLIES TO T1 MODE PER-CHANNEL CONTROL TR.PCPR.3 1 SIGNALING BUFFERS TSIG 0 TSER
10.9.3 Processor-Based Transmit Signaling
In processor-based mode, signaling data is loaded into the transmit signaling registers (TS1-TS16) by the host interface. On multiframe boundaries, the contents of these registers are loaded into a shift register for placement in the appropriate bit position in the outgoing data stream. The user can employ the transmit multiframe interrupt in status register 4 (TR.SR4.4) to know when to update the signaling bits. The user need not update any transmit signaling register for which there is no change-of-state for that register. Each transmit signaling register contains the robbed-bit signaling (T1) or TS16 CAS signaling (E1) for two time slots that are inserted into the outgoing stream, if enabled to do so through TR.T1TCR1.4 (T1 mode) or TR.E1TCR1.6 (E1 mode). In T1 mode, only TS1-TS12 are used. Signaling data can be sourced from the TR.TS registers on a per-channel basis by using the software signaling insertion enable registers, TR.SSIE1-TRSSIE4. 10.9.3.1 T1 Mode In T1 ESF framing mode, there are four signaling bits per channel (A, B, C, and D). TS1-TS12 contain a full multiframe of signaling data. In T1 D4 framing mode, there are only two signaling bits per channel (A and B). In T1 D4 framing mode, the framer uses the C and D bit positions as the A and B bit positions for the next multiframe. In D4 mode, two multiframes of signaling data can be loaded into TS1-TS12. The framer loads the contents of TS1- TS12 into the outgoing shift register every other D4 multiframe. In D4 mode, the host should load new contents into TS1-TS12 on every other multiframe boundary and no later than 120s after the boundary. In T1 mode, only registers TR.SSIE1-TR.SSIE3 are used since there are only 24 channels in a T1 frame.
84 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver 10.9.3.2 E1 Mode In E1 mode, TS16 carries the signaling information. This information can be in either CCS (common channel signaling) or CAS (channel associated signaling) format. The 32 time slots are referenced by two different channel number schemes in E1. In "Channel" numbering, TS0-TS31 are labeled channels 1 through 32. In "Phone Channel" numbering, TS1-TS15 are labeled channel 1 through channel 15 and TS17-TS31 are labeled channel 15 through channel 30. In E1 CAS mode, the CAS signaling alignment/alarm byte can be sourced from the transmit signaling registers along with the signaling data.
Table 10-9. Time Slot Numbering Schemes
01234567891 0 12345678911 Channel 01 1234567891 Phone Channel 0
TS
1 1 1 2 1 1
1 2 1 3 1 2
1 3 1 4 1 3
1 4 1 5 1 4
1 5 1 6 1 5
1 6 1 7
1 7 1 8 1 6
1 8 1 9 1 7
1 9 2 0 1 8
2 0 2 1 1 9
2 1 2 2 2 0
2 2 2 3 2 1
2 3 2 4 2 2
2 4 2 5 2 3
2 5 2 6 2 4
2 6 2 7 2 5
2 7 2 8 2 6
2 8 2 9 2 7
2 9 3 0 2 8
3 0 3 1 2 9
3 1 3 2 3 0
10.9.4 Hardware-Based Transmit Signaling
In hardware-based mode, signaling data is input through the TSIG pin. This signaling PCM stream is buffered and inserted to the data stream being input at the TSERI pin. Signaling data can be inserted on a per-channel basis by the transmit hardware-signaling channel-select (THSCS) function. The user has the ability to control which channels are to have signaling data from the TSIG pin inserted into them on a per-channel basis. See Section 10.2 for details on using this per-channel (THSCS) feature. The signaling insertion capabilities of the framer are available whether the transmit-side elastic store is enabled or disabled. If the elastic store is enabled, the backplane clock (TSYSCLK) can be either 1.544MHz or 2.048MHz. Also, if the elastic is enabled in conjunction with transmit hardware signaling, CCR3.7 must be set = 0.
85 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.10 Per-Channel Idle Code Generation
Channel data can be replaced by an idle code on a per-channel basis in the transmit and receive directions. When operated in the T1 mode, only the first 24 channels are used by the device, the remaining channels, CH25-CH32, are not used. The device contains a 64-byte idle code array accessed by the idle array address register (TR.IAAR) and the perchannel idle code register (TR.PCICR). The contents of the array contain the idle codes to be substituted into the appropriate transmit or receive channels. This substitution can be enabled and disabled on a per-channel basis by the transmit-channel idle code-enable registers (TR.TCICE1-4) and receive-channel idle code-enable registers (TR.RCICE1-4). To program idle codes, first select a channel by writing to the TR.IAAR register. Then write the idle code to the TR.PCICR register. For successive writes there is no need to load the TR.IAAR with the next consecutive address. The TR.IAAR register automatically increments after a write to the TR.PCICR register. The auto increment feature can be used for read operations as well. Bits 6 and 7 of the TR.IAAR register can be used to block write a common idle code to all transmit or receive positions in the array with a single write to the TR.PCICR register. Bits 6 and 7 of the TR.IAAR register should not be used for read operations. TR.TCICE1-4 and TR.RCICE1-4 are used to enable idle code replacement on a per-channel basis.
Table 10-10. Idle-Code Array Address Mapping
BITS 0 to 5 OF IAAR REGISTER 0 1 2 -- -- 30 31 32 33 34 -- -- 62 63 MAPS TO CHANNEL Transmit Channel 1 Transmit Channel 2 Transmit Channel 3 -- -- Transmit Channel 31 Transmit Channel 32 Receive Channel 1 Receive Channel 2 Receive Channel 3 -- -- Receive Channel 31 Receive Channel 32
86 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.10.1 Idle-Code Programming Examples
Example 1 Sets transmit channel 3 idle code to 7Eh.
Write TR.IAAR = 02h Write TR.PCICR = 7Eh ;select channel 3 in the array ;set idle code to 7Eh
Example 2 Sets transmit channels 3, 4, 5, and 6 idle code to 7Eh and enables transmission of idle codes for those channels.
Write Write Write Write Write Write TR.IAAR = 02h TR.PCICR = 7Eh TR.PCICR = 7Eh TR.PCICR = 7Eh TR.PCICR = 7Eh TR.TCICE1 = 3Ch ;select channel 3 in the array ;set channel 3 idle code to 7Eh ;set channel 4 idle code to 7Eh ;set channel 5 idle code to 7Eh ;set channel 6 idle code to 7Eh ;enable transmission of idle codes for channels 3,4,5, and 6
Example 3 Sets transmit channels 3, 4, 5, and 6 idle code to 7Eh, EEh, FFh, and 7Eh, respectively.
Write Write Write Write Write TR.IAAR = 02h TR.PCICR = 7Eh TR.PCICR = EEh TR.PCICR = FFh TR.PCICR = 7Eh
Example 4 Sets all transmit idle codes to 7Eh.
Write TR.IAAR = 4xh Write TR.PCICR = 7Eh
Example 5 Sets all receive and transmit idle codes to 7Eh and enables idle code substitution in all E1 transmit and receive channels.
Write TR.IAAR = Cxh ;enable block write to all transmit and receive positions in the array Write TR.PCICR = 7Eh ;7Eh is idle code Write TR.TCICE1 = FEh ;enable idle code substitution for transmit channels 2 through 8 ;Although an idle code was programmed for channel 1 by the block write ;function above, enabling it for channel 1 would step on the frame ;alignment, alarms, and Sa bits Write TR.TCICE2 = FFh ;enable idle code substitution for transmit channels 9 through 16 Write TR.TCICE3 = FEh ;enable idle code substitution for transmit channels 18 through 24 ;Although an idle code was programmed for channel 17 by the block write ;function above, enabling it for channel 17 would step on the CAS frame ;alignment, and signaling information Write TR.TCICE4 = FFh ;enable idle code substitution for transmit channels 25 through 32 Write TR.RCICE1 = FEh ;enable idle code substitution for receive channels 2 through 8 Write TR.RCICE2 = FFh ;enable idle code substitution for receive channels 9 through 16 Write TR.RCICE3 = FEh ;enable idle code substitution for receive channels 18 through 24 Write TR.RCICE4 = FFh ;enable idle code substitution for receive channels 25 through 32
The transmit-channel idle-code enable registers (TR.TCICE1/2/3/4) are used to determine which of the 24 T1 or 32 E1 channels from the backplane to the T1 or E1 line should be overwritten with the code placed in the per-channel code array. The receive-channel idle-code enable registers (TR.RCICE1/2/3/4) are used to determine which of the 24 T1 or 32 E1 channels from the backplane to the T1 or E1 line should be overwritten with the code placed in the per-channel code array.
87 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.11 Channel Blocking Registers
The receive channel blocking registers (TR.RCBR1/TR.RCBR2/TR.RCBR3/TR.RCBR4) and the transmit channel blocking registers (TR.TCBR1/TR.TCBR2/TR.TCBR3/TR.TCBR4) control RCHBLK and TCHBLK pins, respectively. The RCHBLK and TCHBLK pins are user-programmable outputs that can be forced either high or low during individual channels. These outputs can be used to block clocks to a USART or LAPD controller in ISDN-PRI applications. When the appropriate bits are set to a 1, the RCHBLK and TCHBLK pins are held high during the entire corresponding channel time. Channels 25 through 32 are ignored when the device is operated in the T1 mode.
10.12 Elastic Stores Operation
The device contains dual two-frame elastic stores, one for the receive direction and one for the transmit direction. Both elastic stores are fully independent. The transmit and receive-side elastic stores can be enabled/disabled independently of each other. Also, each elastic store can interface to either a 1.544MHz or 2.048MHz/4.096MHz/ 8.192MHz/16.384MHz backplane without regard to the backplane rate the other elastic store is interfacing to. The elastic stores have two main purposes. Firstly, they can be used for rate conversion. When the device is in the T1 mode, the elastic stores can rate-convert the T1 data stream to a 2.048MHz backplane. In E1 mode, the elastic store can rate-convert the E1 data stream to a 1.544MHz backplane. Secondly, they can be used to absorb the differences in frequency and phase between the T1 or E1 data stream and an asynchronous (i.e., not locked) backplane clock, which can be 1.544MHz or 2.048MHz. In this mode, the elastic stores manage the rate difference and perform controlled slips, deleting or repeating frames of data in order to manage the difference between the network and the backplane. The elastic stores can also be used to multiplex T1 or E1 data streams into higher backplane rates.
10.12.1 Receive Elastic Store
See the TR.IOCR1 and TR.IOCR2 registers for information about clock and I/O configurations. If the receive-side elastic store is enabled, then the user must provide either a 1.544MHz or 2.048MHz clock at the RSYSCLK pin. The user has the option of either providing a frame/multiframe sync at the RSYNC pin or having the RSYNC pin provide a pulse on frame/multiframe boundaries. If signaling reinsertion is enabled, signaling data in TS16 is realigned to the multiframe sync input on RSYNC. Otherwise, a multiframe sync input on RSYNC is treated as a simple frame boundary by the elastic store. The framer always indicates frame boundaries on the network side of the elastic store by the RFSYNC output, whether the elastic store is enabled or not. Multiframe boundaries are always indicated by the RMSYNC output. If the elastic store is enabled, then RMSYNC outputs the multiframe boundary on the backplane side of the elastic store. 10.12.1.1 T1 Mode If the user selects to apply a 2.048MHz clock to the RSYSCLK pin, then the data output at RSERO is forced to all 1s every fourth channel and the F-bit is passed into the MSB of TS0. Hence, channels 1 (bits 1-7), 5, 9, 13, 17, 21, 25, and 29 [time slots 0 (bits 1-7), 4, 8, 12, 16, 20, 24, and 28] are forced to a 1. Also, in 2.048MHz applications, the RCHBLK output is forced high during the same channels as the RSERO pin. This is useful in T1-to-E1 conversion applications. If the two-frame elastic buffer either fills or empties, a controlled slip occurs. If the buffer empties, then a full frame of data is repeated at RSERO, and the TR.SR5.0 and TR.SR5.1 bits are set to a 1. If the buffer fills, then a full frame of data is deleted, and the TR.SR5.0 and TR.SR5.2 bits are set to a 1. 10.12.1.2 E1 Mode If the elastic store is enabled, then either CAS or CRC4 multiframe boundaries are indicated through the RMSYNC output. If the user selects to apply a 1.544MHz clock to the RSYSCLK pin, then every fourth channel of the received E1 data is deleted and an F-bit position, which is forced to 1, is inserted. Hence, channels 1, 5, 9, 13, 17, 21, 25, and 29 (time slots 0, 4, 8, 12, 16, 20, 24, and 28) are deleted from the received E1 data stream. Also, in 1.544MHz applications, the RCHBLK output is not active in channels 25 through 32 (i.e., RCBR4 is not active). If the two-frame elastic buffer either fills or empties, a controlled slip occurs. If the buffer empties, then a full frame of data is repeated at RSERO, and the TR.SR5.0 and TR.SR5.1 bits are set to a 1. If the buffer fills, then a full frame of data is deleted, and the TR.SR5.0 and TR.SR5.2 bits are set to a 1. 88 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.12.2 Transmit Elastic Store
See the TR.IOCR1 and TR.IOCR2 registers for information about clock and I/O configurations. The operation of the transmit elastic store is very similar to the receive side. If the transmit-side elastic store is enabled, a 1.544MHz or 2.048MHz clock can be applied to the TSYSCLK input. Controlled slips in the transmit elastic store are reported in the TR.SR5.3 bit, and the direction of the slip is reported in the TR.SR5.4 and TR.SR5.5 bits. If hardware signaling insertion is not enabled, TR.CCR3.7 should be set = 1. 10.12.2.1 T1 Mode If the user selects to apply a 2.048MHz clock to the TSYSCLK pin, then the data input at TSERI is ignored every fourth channel. Therefore channels 1, 5, 9, 13, 17, 21, 25, and 29 (time slots 0, 4, 8, 12, 16, 20, 24, and 28) are ignored. The user can supply frame or multiframe sync pulse to the TSSYNC input. Also, in 2.048MHz applications, the TCHBLK output is forced high during the channels ignored by the framer. 10.12.2.2 E1 Mode A 1.544MHz or 2.048MHz clock can be applied to the TSYSCLK input. The user must supply a frame sync pulse or a multiframe sync pulse to the TSSYNC input.
10.12.3 Elastic Stores Initialization
There are two elastic store initializations that can be used to improve performance in certain applications, elastic store reset and elastic store align. Both of these involve the manipulation of the elastic store's read and write pointers and are useful primarily in synchronous applications (RSYSCLK/TSYSCLK are locked to RCLKO/TCLKT, respectively) (Table 10-11).
Table 10-11. Elastic Store Delay After Initialization
INITIALIZATION Receive Elastic Store Reset Transmit Elastic Store Reset Receive Elastic Store Align Transmit Elastic Store Align REGISTER BIT TR.ESCR.2 TR.ESCR.6 TR.ESCR.3 TR.ESCR.7 DELAY 8 Clocks < Delay < 1 Frame 1 Frame < Delay < 2 Frames 1/2 Frame < Delay < 1 1/2 Frames 1/2 Frame < Delay < 1 1/2 Frames
10.12.4 Minimum Delay Mode
Elastic store minimum delay mode can be used when the elastic store's system clock is locked to its network clock (i.e., RCLKO locked to RSYSCLK for the receive side and TCLKT locked to TSYSCLK for the transmit side). TR.ESCR.5 and TR.ESCR.1 enable the transmit and receive elastic store minimum delay modes. When enabled, the elastic stores are forced to a maximum depth of 32 bits instead of the normal two-frame depth. This feature is useful primarily in applications that interface to a 2.048MHz bus. Certain restrictions apply when minimum delay mode is used. In addition to the restriction mentioned above, RSYNC must be configured as an output when the receive elastic store is in minimum delay mode; TSYNC must be configured as an output when transmit minimum delay mode is enabled. In a typical application, RSYSCLK and TSYSCLK are locked to RCLKO, and RSYNC (frame output mode) is connected to TSSYNC (frame input mode). All of the slip contention logic in the framer is disabled (since slips cannot occur). On power-up, after the RSYSCLK and TSYSCLK signals have locked to their respective network clock signals, the elastic store reset bits (TR.ESCR.2 and TR.ESCR.6) should be toggled from a 0 to a 1 to ensure proper operation.
89 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.13 G.706 Intermediate CRC-4 Updating (E1 Mode Only)
The device can implement the G.706 CRC-4 recalculation at intermediate path points. When this mode is enabled, the data stream presented at TSERI already has the FAS/NFAS, CRC multiframe alignment word, and CRC-4 checksum in time slot 0. The user can modify the Sa bit positions. This change in data content is used to modify the CRC-4 checksum. This modification, however, does not corrupt any error information the original CRC-4 checksum may contain. In this mode of operation, TSYNC must be configured to multiframe mode. The data at TSERI must be aligned to the TSYNC signal. If TSYNC is an input, then the user must assert TSYNC aligned at the beginning of the multiframe relative to TSERI. If TSYNC is an output, the user must multiframe-align the data presented to TSERI.
Figure 10-4. CRC-4 Recalculate Method
TPOSO/TNEGO
INSERT NEW CRC-4 CODE
EXTRACT OLD CRC-4 CODE
TSER
+
CRC-4 CALCULATOR
XOR
MODIFY Sa BIT POSITIONS
NEW Sa BIT DATA
90 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.14 T1 Bit-Oriented Code (BOC) Controller
The transceiver contains a BOC generator on the transmit side and a BOC detector on the receive side. The BOC function is available only in T1 mode.
10.14.1 Transmit BOC
Bits 0 to 5 in the TR.TFDL register contain the BOC message to be transmitted. Setting TR.BOCC.0 = 1 causes the transmit BOC controller to immediately begin inserting the BOC sequence into the FDL bit position. The transmit BOC controller automatically provides the abort sequence. BOC messages are transmitted as long as TR.BOCC.0 is set. Transmit a BOC 1) Write 6-bit code into the TR.TFDL register. 2) Set the SBOC bit in TR.BOCC = 1.
10.15 Receive BOC
The receive BOC function is enabled by setting TR.BOCC.4 = 1. The TR.RFDL register now operates as the receive BOC message and information register. The lower six bits of the TR.RFDL register (BOC message bits) are preset to all 1s. When the BOC bits change state, the BOC change-of-state indicator, TR.SR8.0, alerts the host. The host then reads the TR.RFDL register to get the BOC status and message. A change-of-state occurs when either a new BOC code has been present for a time determined by the receive BOC filter bits RBF0 and RBF1 in the TR.BOCC register, or a nonvalid code is being received. Receive a BOC 1) Set integration time through TR.BOCC.1 and TR.BOCC.2. 2) Enable the receive BOC function (TR.BOCC.4 = 1). 3) Enable interrupt (TR.IMR8.0 = 1). 4) Wait for interrupt to occur. 5) Read the TR.RFDL register. 6) If TR.SR2.7 = 1, then a valid BOC message was received. The lower six bits of the TR.RFDL register comprise the message.
91 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.16 Additional (Sa) and International (Si) Bit Operation (E1 Only)
When operated in the E1 mode, the transceiver provides two methods for accessing the Sa and the Si bits. The first method involves using the internal TR.RAF/ TR.RNAF and TR.TAF/ TR.TNAF registers (Section 10.16.1). The second method, which is covered in Section 10.16.2, involves an expanded version of the first method.
10.16.1 Method 1: Internal Register Scheme Based on Double-Frame
On the receive side, the TR.RAF and TR.RNAF registers always report the data as it received in the Sa and Si bit locations. The TR.RAF and TR.RNAF registers are updated on align-frame boundaries. The setting of the receive align frame bit in Status Register 4 (TR.SR4.0) indicates that the contents of the TR.RAF and TR.RNAF have been updated. The host can use the TR.SR4.0 bit to know when to read the TR.RAF and TR.RNAF registers. The host has 250s to retrieve the data before it is lost. On the transmit side, data is sampled from the TR.TAF and TR.TNAF registers with the setting of the transmit align frame bit in Status Register 4 (TR.SR4.3). The host can use the TR.SR4.3 bit to know when to update the TR.TAF and TR.TNAF registers. It has 250s to update the data or else the old data is retransmitted. If the TR.TAF and TR.TNAF registers are only being used to source the align frame and nonalign frame-sync patterns, then the host need only write once to these registers. Data in the Si bit position is overwritten if either the framer is (1) programmed to source the Si bits from the TSERI pin, (2) in the CRC4 mode, or (3) has automatic E-bit insertion enabled. Data in the Sa bit position is overwritten if any of the TR.E1TCR2.3 to TR.E1TCR2.7 bits are set to 1.
10.16.2 Method 2: Internal Register Scheme Based on CRC4 Multiframe
The receive side contains a set of eight registers (TR.RSiAF, TR.RSiNAF, TR.RRA, and TR.RSa4 - TR.RSa8) that report the Si and Sa bits as they are received. These registers are updated with the setting of the receive CRC4 multiframe bit in Status Register 2 (TR.SR4.1). The host can use the TR.SR4.1 bit to know when to read these registers. The user has 2ms to retrieve the data before it is lost. The MSB of each register is the first received. See the following register descriptions for more details. The transmit side also contains a set of eight registers (TR.TSiAF, TR.TSiNAF, TR.TRA, and TR.TSa4 - TR.TSa8) that, through the transmit Sa bit control register (TR.TSACR), can be programmed to insert Si and Sa data. Data is sampled from these registers with the setting of the transmit multiframe bit in Status Register 2 (TR.SR4.4). The host can use the TR.SR4.4 bit to know when to update these registers. It has 2ms to update the data or else the old data is retransmitted. The MSB of each register is the first bit transmitted. See the register descriptions for more details.
92 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.17 Additional HDLC Controllers in T1/E1/J1 Transceiver
This device has two enhanced HDLC controllers, HDLC #1 and HDLC #2. Each controller is configurable for use with time slots, Sa4 to Sa8 bits (E1 mode), or the FDL (T1 mode). Each HDLC controller has 128-byte buffers in the transmit and receive paths. When used with time slots, the user can select any time slot or multiple time slots, contiguous or noncontiguous, as well as any specific bits within the time slot(s) to assign to the HDLC controllers. The user must not map both transmit HDLC controllers to the same Sa bits, time slots or, in T1 mode, map both controllers to the FDL. HDLC #1 and HDLC #2 are identical in operation and therefore the following operational description refers only to a singular controller. The HDLC controller performs the entire necessary overhead for generating and receiving performance report messages (PRMs) as described in ANSI T1.403 and the messages as described in AT&T TR54016. The HDLC controller automatically generates and detects flags, generates and checks the CRC check sum, generates and detects abort sequences, stuffs and destuffs zeros, and byte aligns to the data stream. The 128-byte buffers in the HDLC controller are large enough to allow a full PRM to be received or transmitted without host intervention. The HDLC registers are divided into four groups: control/configuration, status/information, mapping, and FIFOs. Table 10-12 lists these registers by group.
10.17.1 HDLC Configuration
The TR.HxTC and TR.HxRC registers perform the basic configuration of the HDLC controllers. Operating features such as CRC generation, zero stuffer, transmit and receive HDLC mapping options, and idle flags are selected here. These registers also reset the HDLC controllers.
93 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 10-12. HDLC Controller Registers
REGISTER FUNCTION CONTROL AND CONFIGURATION General control over the transmit HDLC controllers TR.H1TC, HDLC #1 Transmit Control Register TR.H2TC, HDLC #2 Transmit Control Register General control over the receive HDLC controllers TR.H1RC, HDLC #1 Receive Control Register TR.H2RC, HDLC #2 Receive Control Register Sets high watermark for receiver and low TR.H1FC, HDLC #1 FIFO Control Register watermark for transmitter TR.H2FC, HDLC #2 FIFO Control Register STATUS AND INFORMATION Key status information for both transmit and receive TR.SR6, HDLC #1 Status Register directions TR.SR7, HDLC #2 Status Register Selects which bits in the status registers (SR7 and TR.IMR6, HDLC #1 Interrupt Mask Register SR8) cause interrupts TR.IMR7, HDLC #2 Interrupt Mask Register Information about HDLC controller TR.INFO4, HDLC #1 and #2 Information Register TR.INFO5, HDLC #1 Information Register TR.INFO6, HDLC #2 Information Register Indicates the number of bytes that can be read TR.H1RPBA, HDLC #1 Receive Packet Bytes Available from the receive FIFO TR.H2RPBA, HDLC #2 Receive Packet Bytes Available Indicates the number of bytes that can be written to TR.H1TFBA, HDLC #1 Transmit FIFO Buffer Available the transmit FIFO TR.H2TFBA, HDLC #2 Transmit FIFO Buffer Available MAPPING Selects which channels are mapped to the receive TR.H1RCS1, TR.H1RCS2, TR.H1RCS3, TR.H1RCS4, HDLC controller HDLC #1 Receive Channel Select Registers TR.H2RCS1, TR.H2RCS2, TR.H2RCS3, TR.H2RCS4, HDLC #2 Receive Channel Select Registers Selects which bits in a channel are used or which TR.H1RTSBS, HDLC #1 Receive TS/Sa Bit Select Sa bits are used by the receive HDLC controller TR.H2RTSBS, HDLC #2 Receive TS/Sa Bit Select Selects which channels are mapped to the transmit TR.H1TCS1, TR.H1TCS2, TR.H1TCS3, TR.H1TCS4, HDLC controller HDLC #1 Transmit Channel Select Registers TR.H2TCS1, TR.H2TCS2, TR.H2TCS3, TR.H2TCS4, HDLC #2 Transmit Channel Select Registers Selects which bits in a channel are used or which TR.H1TTSBS, HDLC # 1 Transmit TS/Sa Bit Select Sa bits are used by the transmit HDLC controller TR.H2TTSBS, HDLC # 2 Transmit TS/Sa Bit Select FIFOs Access to 128-byte receive FIFO TR.H1RF, HDLC #1 Receive FIFO Register TR.H2RF, HDLC #1 Receive FIFO Register Access to 128-byte transmit FIFO TR.H1TF, HDLC #1 Transmit FIFO Register TR.H2TF, HDLC #2 Transmit FIFO Register
94 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.17.2
FIFO Control
The FIFO control register (TR.HxFC) controls and sets the watermarks for the transmit and receive FIFOs. Bits 3, 4, and 5 set the transmit low watermark and the lower 3 bits set the receive high watermark. When the transmit FIFO empties below the low watermark, the TLWM bit in the appropriate HDLC status register TR.SR6 or TR.SR7 is set. TLWM is a real-time bit and remains set as long as the transmit FIFO's read pointer is below the watermark. If enabled, this condition can also cause an interrupt through the INT pin. When the receive FIFO fills above the high watermark, the RHWM bit in the appropriate HDLC status register is set. RHWM is a real-time bit and remains set as long as the receive FIFO's write pointer is above the watermark. If enabled, this condition can also cause an interrupt through the INT pin.
10.17.3 HDLC Mapping
The HDLC controllers must be assigned a space in the T1/E1 bandwidth in which they transmit and receive data. The controllers can be mapped to either the FDL (T1), Sa bits (E1), or to channels. If mapped to channels, then any channel or combination of channels, contiguous or not, can be assigned to an HDLC controller. When assigned to a channel(s), any combination of bits within the channel(s) can be avoided. The TR.HxRCS1 - TR.HxRCS4 registers are used to assign the receive controllers to channels 1-24 (T1) or 1-32 (E1) according to the following table: REGISTER TR.HxRCS1 TR.HxRCS2 TR.HxRCS3 TR.HxRCS4 CHANNELS 1-8 9-16 17-24 25-32
The TR.HxTCS1 - TR.HxTCS4 registers are used to assign the transmit controllers to channels 1-24 (T1) or 1-32 (E1) according to the following table. REGISTER TR.HxTCS1 TR.HxTCS2 TR.HxTCS3 TR.HxTCS4 CHANNELS 1-8 9-16 17-24 25-32
95 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.17.4
FIFO Information
The transmit FIFO buffer-available register indicates the number of bytes that can be written into the transmit FIFO. The count form this register informs the host as to how many bytes can be written into the transmit FIFO without overflowing the buffer.
10.17.5
Receive Packet-Bytes Available
The lower 7 bits of the receive packet-bytes available register indicates the number of bytes (0 through 127) that can be read from the receive FIFO. The value indicated by this register (lower seven bits) informs the host as to how many bytes can be read from the receive FIFO without going past the end of a message. This value refers to one of four possibilities: the first part of a packet, the continuation of a packet, the last part of a packet, or a complete packet. After reading the number of bytes indicated by this register, the host then checks the HDLC information register for detailed message status. If the value in the TR.HxRPBA register refers to the beginning portion of a message or continuation of a message, then the MSB of the TR.HxRPBA register returns a value of 1. This indicates that the host can safely read the number of bytes returned by the lower seven bits of the TR.HxRPBA register, but there is no need to check the information register since the packet has not yet terminated (successfully or otherwise).
10.17.5.1 Receive HDLC Code Example The following is an example of a receive HDLC routine: 1) Reset receive HDLC controller. 2) Set HDLC mode, mapping, and high watermark. 3) Start new message buffer. 4) Enable RPE and RHWM interrupts. 5) Wait for interrupt. 6) Disable RPE and RHWM interrupts. 7) Read TR.HxRPBA register. N = TR.HxRPBA (lower 7 bits are byte count, MSB is status). 8) Read (N and 7Fh) bytes from receive FIFO and store in message buffer. 9) Read TR.INFO5 register. 10) If PS2, PS1, PS0 = 000, then go to Step 4. 11) If PS2, PS1, PS0 = 001, then packet terminated OK, save present message buffer. 12) If PS2, PS1, PS0 = 010, then packet terminated with CRC error. 13) If PS2, PS1, PS0 = 011, then packet aborted. 14) If PS2, PS1, PS0 = 100, then FIFO overflowed. 15) Go to Step 3.
96 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.18 Legacy FDL Support (T1 Mode)
10.18.1 Overview
To provide backward compatibility to the older DS21x52 T1 device, the transceiver maintains the circuitry that existed in the previous generation of the T1 framer. In new applications, it is recommended that the HDLC controllers and BOC controller described in Section 10.14 and 10.17 are used.
10.18.2
Receive Section
In the receive section, the recovered FDL bits or Fs bits are shifted bit-by-bit into the receive FDL register (TR.RFDL). Because the TR.RFDL is 8 bits in length, it fills up every 2ms (8 x 250s). The framer signals an external microcontroller that the buffer has filled through the TR.SR8.3 bit. If enabled through TR.IMR8.3, the INT pin toggles low, indicating that the buffer has filled and needs to be read. The user has 2ms to read this data before it is lost. If the byte in the TR.RFDL matches either of the bytes programmed into the TR.RFDLM1 or TR.RFDLM2 registers, then the TR.SR8.1 bit is set to a 1 and the INT pin toggles low if enabled through TR.IMR8.1. This feature allows an external microcontroller to ignore the FDL or Fs pattern until an important event occurs. The framer also contains a zero destuffer, which is controlled through the TR.T1RCR2.3 bit. In both ANSI T1.403 and TR54016, communications on the FDL follows a subset of an LAPD protocol. The LAPD protocol states that no more than five 1s should be transmitted in a row so that the data does not resemble an opening or closing flag (01111110) or an abort signal (11111111). If enabled through TR.T1RCR2.3, the device automatically looks for five 1s in a row, followed by a 0. If it finds such a pattern, it automatically removes the zero. If the zero destuffer sees six or more 1s in a row followed by a 0, the 0 is not removed. The TR.T1RCR2.3 bit should always be set to a 1 when the device is extracting the FDL. Refer to Application Note 335: DS2141A, DS2151 Controlling the FDL for information about using the device in FDL applications in this legacy support mode.
97 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.18.3 Transmit Section
The transmit section shifts out into the T1 data stream either the FDL (in the ESF framing mode) or the Fs bits (in the D4 framing mode) contained in the transmit FDL register (TR.TFDL). When a new value is written to TR.TFDL, it is multiplexed serially (LSB first) into the proper position in the outgoing T1 data stream. After the full 8 bits have been shifted out, the framer signals the host microcontroller by setting the TR.SR8.2 bit to a 1 that the buffer is empty and that more data is needed. The INT also toggles low if enabled through TR.IMR8.2. The user has 2ms to update TR.TFDL with a new value. If TR.TFDL is not updated, the old value in TR.TFDL is transmitted once again. The framer also contains a zero stuffer that is controlled through the TR.T1TCR2.5 bit. In both ANSI T1.403 and TR54016, communications on the FDL follows a subset of an LAPD protocol. The LAPD protocol states that no more than five 1s should be transmitted in a row so that the data does not resemble an opening or closing flag (01111110) or an abort signal (11111111). If enabled through TR.T1TCR2.5, the framer automatically looks for five 1s in a row. If it finds such a pattern, it automatically inserts a 0 after the five 1s. The TR.T1TCR2.5 bit should always be set to a 1 when the framer is inserting the FDL.
10.19 D4/SLC-96 Operation
In the D4 framing mode, the framer uses the TR.TFDL register to insert the Fs framing pattern. To allow the device to properly insert the Fs framing pattern, the TR.TFDL register at address C1h must be programmed to 1Ch and the following bits must be programmed as shown: TR.T1TCR1.2 = 0 (source Fs data from the TR.TFDL register) TR.T1TCR2.6 = 1 (allow the TR.TFDL register to load on multiframe boundaries) Since the SLC-96 message fields share the Fs-bit position, the user can access these message fields through the TR.TFDL and TR.RFDL registers. Refer to Application Note 345: DS2141A, DS2151, DS2152 SLC-96 for a detailed description about implementing an SLC-96 function.
98 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.20 Programmable In-Band Loop Code Generation and Detection
The transceiver has the ability to generate and detect a repeating bit pattern from one to eight bits or 16 bits in length. This function is available only in T1 mode. To transmit a pattern, the user loads the pattern into the transmit code-definition registers (TR.TCD1 and TR.TCD2) and selects the proper length of the pattern by setting the TC0 and TC1 bits in the in-band code control (TR.IBCC) register. When generating a 1-, 2-, 4-, 8-, or 16-bit pattern, both transmit code-definition registers must be filled with the proper code. Generation of a 3-, 5-, 6-, and 7bit pattern only requires TR.TCD1 to be filled. Once this is accomplished, the pattern is transmitted as long as the TLOOP control bit (TR.T1CCR1.0) is enabled. Normally (unless the transmit formatter is programmed to not insert the F-bit position) the framer overwrites the repeating pattern once every 193 bits to send the F-bit position. For example, to transmit the standard "loop-up" code for CSUs, which is a repeating pattern of ...10000100001... , set TR.TCD1 = 80h, TR.IBCC = 0, and TR.T1CCR1.0 = 1. The framer has three programmable pattern detectors. Typically two of the detectors are used for "loop-up" and "loop-down" code detection. The user programs the codes to be detected in the receive up-code definition (TR.RUPCD1 and TR.RUPCD2) registers and the receive down-code definition (TR.RDNCD1 and TR.RDNCD2) registers, and the length of each pattern is selected through the TR.IBCC register. There is a third detector (spare) that is defined and controlled through the TR.RSCD1/ TR.RSCD2 and TR.RSCC registers. When detecting a 16-bit pattern, both receive code-definition registers are used together to form a 16-bit register. For 8-bit patterns, both receive code-definition registers are filled with the same value. Detection of a 1-, 2-, 3-, 4-, 5-, 6-, and 7-bit pattern only requires the first receive code-definition register to be filled. The framer detects repeating pattern codes in both framed and unframed circumstances with bit error rates as high as 10E-2. The detectors are capable of handling both F-bit inserted and F-bit overwrite patterns. Writing the least significant byte of the receive code-definition register resets the integration period for that detector. The code detector has a nominal integration period of 36ms. Hence, after about 36ms of receiving a valid code, the proper status bit (LUP at TR.SR3.5, LDN at TR.SR3.6, and LSPARE at TR.SR3.7) is set to a 1. Normally codes are sent for a period of five seconds. It is recommended that the software poll the framer every 50ms to 1000ms until five seconds has elapsed to ensure the code is continuously present.
99 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.21 Line Interface Unit (LIU)
The LIU contains three sections: the receiver that handles clock and data recovery, the transmitter that waveshapes and drives the T1 line, and the jitter attenuator. These three sections are controlled by the line interface control registers (LIC1-LIC4), which are described in the following sections. The LIU has its own T1/E1 mode-select bit and can operate independently of the framer function. The transceiver can switch between T1 or E1 networks without changing external components on the transmit or receive side. Figure 10-7 shows a network connection using minimal components. In this configuration, the transceiver can connect to T1, J1, or E1 (75W or 120W) without component changes. The receiver can adjust the 120W termination to 100W or 75W. The transmitter can adjust its output impedance to provide high return-loss characteristics for 120W, 100W, and 75W lines. Other components can be added to this configuration to meet safety and network protection requirements (Section 10.25).
10.21.1 LIU Operation
The analog AMI/HDB3 waveform off the E1 line or the AMI/B8ZS waveform off of the T1 line is transformer-coupled into the RTIP and RRING pins of the device. The user has the option to use internal termination, software selectable for 75W/100W/120W applications, or external termination. The LIU recovers clock and data from the analog signal and passes it through the jitter-attenuation mux outputting the received line clock at RDCLKO and bipolar or NRZ data at RPOSO and RNEGO. The transceiver contains an active filter that reconstructs the analogreceived signal for the nonlinear losses that occur in transmission. The receive circuitry also is configurable for various monitor applications. The device has a usable receive sensitivity of 0dB to -43dB for E1 and 0dB to -36dB for T1, which allow the device to operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6k feet (T1) in length. Data input at TPOSI and TNEGI is sent through the jitter-attenuation mux to the waveshaping circuitry and line driver. The transceiver drives the E1 or T1 line from the TTIP and TRING pins through a coupling transformer. The line driver can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for T1.
10.21.2 Receiver
The receiver contains a digital clock recovery system. The device couples to the receive E1 or T1 twisted pair (or coaxial cable in 75W E1 applications) through a 1:1 transformer. See Table 10-13 for transformer details. The device has the option of using software-selectable termination requiring only a single fixed pair of termination resistors. The transceiver's LIU is designed to be fully software selectable for E1 and T1, requiring no change to any external resistors for the receive side. The receive side allows the user to configure the transceiver for 75W, 100W, or 120W receive termination by setting the RT1 (TR.LIC4.1) and RT0 (TR.LIC4.0) bits. When using the internal termination feature, the resistors labeled R in Figure 10-7 should be 60W each. If external termination is used, RT1 and RT0 should be set to 0 and the resistors labeled R in Figure 10-7 should be 37.5W, 50W, or 60W each, depending on the line impedance. There are two ranges of user-selectable receive sensitivity for T1 and E1. The EGL bit of TR.LIC1 (TR.LIC1.4) selects the full or limited sensitivity. The resultant E1 or T1 clock derived from MCLK is multiplied by 16 through an internal PLL and fed to the clock recovery system. The clock recovery system uses the clock from the PLL circuit to form a 16-times over-sampler that is used to recover the clock and data. This over-sampling technique offers outstanding performance to meet jitter tolerance specifications shown in Figure 10-10. Normally, the clock that is output at the RCLKO pin is the recovered clock from the E1 AMI/HDB3 or T1 AMI/B8ZS waveform presented at the RTIP and RRING inputs. If the jitter attenuator is placed in the receive path (as is the case in most applications), the jitter attenuator restores the RCLKO to an approximate 50% duty cycle. If the jitter attenuator is either placed in the transmit path or is disabled, the RCLKO output can exhibit slightly shorter high cycles of the clock. This is because of the highly over-sampled digital-clock recovery circuitry. See the Receive AC Timing Characteristics in Section 13.9 for more details. When no signal is present at RTIP and RRING, a receive carrier loss (RCL) condition occurs and the RCLKO is derived from the JACLK source.
100 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver 10.21.2.1 Receive Level Indicator and Threshold Interrupt The device reports the signal strength at RTIP and RRING in 2.5dB increments through RL3-RL0 located in Information Register 2 (TR.INFO2). This feature is helpful when trouble-shooting line-performance problems. The device can initiate an interrupt whenever the input falls below a certain level through the input-level under-threshold indicator (TR.SR1.7). Using the RLT0-RLT4 bits of the TR.CCR4 register, the user can set a threshold in 2.5dB increments. The TR.SR1.7 bit is set whenever the input level at RTIP and RRING falls below the threshold set by the value in RLT0-RLT4. The level must remain below the programmed threshold for approximately 50ms for this bit to be set. The accuracy of the receive level indication is 1 LSB (2.5dB) from 25C to 85C and 2 LSBs (5dB) from -40C to 25C.
10.21.2.2 Receive G.703 Synchronization Signal (E1 Mode) The transceiver is capable of receiving a 2.048MHz square-wave synchronization clock as specified in Section 13 of ITU G.703, October 1998. In order to use the device in this mode, set the receive synchronization clock enable (TR.LIC3.2) = 1. 10.21.2.3 Monitor Mode Monitor applications in both E1 and T1 require various flat gain settings for the receive-side circuitry. The device can be programmed to support these applications through the monitor mode control bits MM1 and MM0 in the TR.LIC3 register (Figure 10-5).
Figure 10-5. Typical Monitor Application
T1/E1 LINE
PRIMARY T1/E1 TERMINATING DEVICE Rm
X F M R
Rm
Rt
T1/E1 XCVR
MONITOR PORT JACK
SECONDARY T1/E1 TERMINATING DEVICE
101 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.21.3 Transmitter
The transceiver uses a phase-lock loop along with a precision digital-to-analog converter (DAC) to create the waveforms that are transmitted onto the E1 or T1 line. The waveforms created by the device meet the latest ETSI, ITU, ANSI, and AT&T specifications. The user selects which waveform is generated by setting the ETS bit (TR.LIC2.7) for E1 or T1 operation, then programming the L2/L1/L0 bits in register TR.LIC1 for the appropriate application. A 2.048MHz or 1.544MHz clock is required at TDCLKI for transmitting data presented at TPOSI and TNEGI. Normally these pins are connected to TCLKO, TPOSO, and TNEGO. However, the LIU can operate in an independent fashion. ITU specification G.703 requires an accuracy of 50ppm for both T1 and E1. TR62411 and ANSI specifications require an accuracy of 32ppm for T1 interfaces. The clock can be sourced internally from RCLKO or JACLK. See TR.LIC2.3, TR.LIC4.4, and TR.LIC4.5 for details. Because of the nature of the transmitter's design, very little jitter (less than 0.005UIP-P broadband from 10Hz to 100kHz) is added to the jitter present on TCLKT. Also, the waveforms created are independent of the duty cycle of TCLKT. The transmitter in the device couples to the E1 or T1 transmit twisted pair (or coaxial cable in some E1 applications) through a 1:2 step-up transformer. For the device to create the proper waveforms, the transformer used must meet the specifications listed in Table 10-13. The device has the option of using software-selectable transmit termination. The transmit line drive has two modes of operation: fixed gain or automatic gain. In the fixed gain mode, the transmitter outputs a fixed current into the network load to achieve a nominal pulse amplitude. In the automatic gain mode, the transmitter adjusts its output level to compensate for slight variances in the network load. See the Transmit Line Build-Out Control (TR.TLBC) register for details. 10.21.3.1 Transmit Short-Circuit Detector/Limiter The device has an automatic short-circuit limiter that limits the source current to 50mA (RMS) into a 1 load. This feature can be disabled by setting the SCLD bit (TR.LIC2.1) = 1. TCLE (TR.INFO2.5) provides a real-time indication of when the current limiter is activated. If the current limiter is disabled, TCLE indicates that a short-circuit condition exists. Status Register TR.SR1.2 provides a latched version of the information, which can be used to activate an interrupt when enabled by the TR.IMR1 register. The TPD bit (TR.LIC1.0) powers down the transmit line driver and three-states the TTIP and TRING pins. 10.21.3.2 Transmit Open-Circuit Detector The device can also detect when the TTIP or TRING outputs are open circuited. TOCD (TR.INFO2.4) provides a real-time indication of when an open circuit is detected. TR.SR1 provides a latched version of the information (TR.SR1.1), which can be used to activate an interrupt when enabled by the TR.IMR1 register. 10.21.3.3 Transmit BPV Error Insertion When IBPV (TR.LIC2.5) is transitioned from a 0 to a 1, the device waits for the next occurrence of three consecutive 1s to insert a BPV. IBPV must be cleared and set again for another BPV error insertion. 10.21.3.4 Transmit G.703 Synchronization Signal (E1 Mode) The transceiver can transmit the 2.048MHz square-wave synchronization clock as specified in Section 13 of ITU G.703, October 1998. In order to transmit the 2.048MHz clock, when in E1 mode, set the transmit synchronization clock enable (TR.LIC3.1) = 1.
102 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.22 MCLK Prescaler
A 16.384MHz, 8.192MHz, 4.096MHz, 2.048MHz, or 1.544MHz clock must be applied at MCLK. ITU specification G.703 requires an accuracy of 50ppm for both T1 and E1. TR62411 and ANSI specifications require an accuracy of 32ppm for T1 interfaces. A prescaler divides the 16MHz, 8MHz, or 4MHz clock down to 2.048MHz. There is an on-board PLL for the jitter attenuator, which converts the 2.048MHz clock to a 1.544MHz rate for T1 applications. Setting JAMUX (TR.LIC2.3) to a logic 0 bypasses this PLL.
10.23 Jitter Attenuator
The device contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits through the JABDS bit (TR.LIC1.2). The 128-bit mode is used in applications where large excursions of wander are expected. The 32-bit mode is used in delay-sensitive applications. The characteristics of the attenuation are shown in Figure 10-12. The jitter attenuator can be placed in either the receive path or the transmit path by appropriately setting or clearing the JAS bit (TR.LIC1.3). Setting the DJA bit (TR.LIC1.1) disables (in effect, removes) the jitter attenuator. On-board circuitry adjusts either the recovered clock from the clock/data recovery block or the clock applied at the TCLKT pin to create a smooth jitter-free clock that is used to clock data out of the jitter attenuator FIFO. It is acceptable to provide a gapped/bursty clock at the TCLKT pin if the jitter attenuator is placed on the transmit side. If the incoming jitter exceeds either 120UIP-P (buffer depth is 128 bits) or 28UIP-P (buffer depth is 32 bits), then the transceiver divides the internal nominal 32.768MHz (E1) or 24.704MHz (T1) clock by either 15 or 17 instead of the normal 16 to keep the buffer from overflowing. When the device divides by either 15 or 17, it also sets the jitter attenuator limit trip (JALT) bit in Status Register 1 (TR.SR1.4).
10.24 CMI (Code Mark Inversion) Option
The device provides a CMI interface for connection to optical transports. This interface is a unipolar 1T2B signal type. Ones are encoded as either a logical 1 or 0 level for the full duration of the clock period. Zeros are encoded as a 0-to-1 transition at the middle of the clock period.
Figure 10-6. CMI Coding
CLOCK DATA CMI
1
1
0
1
0
0
1
Transmit and receive CMI are enabled through TR.LIC4.7. When this register bit is set, the TTIP pin outputs CMIcoded data at normal levels. This signal can be used to directly drive an optical interface. When CMI is enabled, the user can also use HDB3/B8ZS coding. When this register bit is set, the RTIP pin becomes a unipolar CMI input. The CMI signal is processed to extract and align the clock with data.
103 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.25 Recommended Circuits Figure 10-7. Basic Interface
VDD
2:1
TRANSMIT LINE C
DS33R11 TTIP DVDD DVSS TRING TVDD TVSS RVDD RRING RVSS R R
0.1F 0.01F
0.1F
10F
+
1:1
RECEIVE LINE
RTIP
0.1F 10F
+
0.1F
NOTE 1: ALL RESISTOR VALUES ARE 1%. NOTE 2: RESISTORS R SHOULD BE SET TO 60W EACH IF THE INTERNAL RECEIVE-SIDE TERMINATION FEATURE IS ENABLED. WHEN THIS FEATURE IS DISABLED, R = 37.5W FOR 75W COAXIAL E1 LINES, 60W FOR 120W TWISTED-PAIR E1 LINES, OR 50W FOR 100W TWISTED-PAIR T1 LINES. NOTE 3: C = 1mF CERAMIC.
Refer to Application Note 324: T1/E1 Network Interface Design for more information on protected interfaces.
Table 10-13. Transformer Specifications
SPECIFICATION Turns Ratio 3.3V Applications Primary Inductance Leakage Inductance Intertwining Capacitance Transmit Transformer DC Resistance Primary (Device Side) Secondary Receive Transformer DC Resistance Primary (Device Side) Secondary RECOMMENDED VALUE 1:1 (receive) and 1:2 (transmit) 2% 600mH (min) 1.0mH (max) 40pF (max) 1.0 (max) 2.0 (max) 1.2 (max) 1.2 (max)
104 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-8. E1 Transmit Pulse Template
1.2 1.1
(IN 75 SYSTEMS, 1.0 ON THE SCALE = 2.37VPEAK IN 120 SYSTEMS, 1.0 ON THE SCALE = 3.00VPEAK) 269ns
1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2
-250 -200 -150 -100 -50 0 50 100 150 200 250 219ns 194ns
SCALED AMPLITUDE
G.703 TEMPLATE
TIME (ns)
Figure 10-9. T1 Transmit Pulse Template
1.2 1.1 1.0 0.9 0.8 0.7 NORMALIZED AMPLITUDE 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 -500 -400 -300 -200 -100 0 100 200 300 400 500 600 700 T1.102/87, T1.403, CB 119 (OCT. 79), AND I.431 TEMPLATE
MAXIMUM CURVE UI Time Amp. -0.77 -0.39 -0.27 -0.27 -0.12 0.00 0.27 0.35 0.93 1.16 -500 -255 -175 -175 -75 0 175 225 600 750 0.05 0.05 0.80 1.15 1.15 1.05 1.05 -0.07 0.05 0.05 MINIMUM CURVE UI Time Amp. -0.77 -0.23 -0.23 -0.15 0.00 0.15 0.23 0.23 0.46 0.66 0.93 1.16 -500 -150 -150 -100 0 100 150 150 300 430 600 750 -0.05 -0.05 0.50 0.95 0.95 0.90 0.50 -0.45 -0.45 -0.20 -0.05 -0.05
TIME (ns)
105 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-10. Jitter Tolerance
1k
UNIT INTERVALS (UIP-P)
DEVICE
100 TR 62411 (DEC. 90) 10 ITU-T G.823 1
TOLERANCE
0.1 1 10 100 1k FREQUENCY (Hz) 10k 100k
Figure 10-11. Jitter Tolerance (E1 Mode)
1k
UNIT INTERVALS (UIP-P)
DEVICE
100
40
TOLERANCE
10
1.5
1
MINIMUM TOLERANCE LEVEL AS PER
ITU G.823 0.1 1
20 2.4k 18k
0.2
10
100 1k FREQUENCY (Hz)
10k
100k
106 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-12. Jitter Attenuation (T1 Mode)
0dB
JITTER ATTENUATION (dB)
-20dB
e rv Cu A
-40dB
rve Cu B
TR 62411 (Dec. 90) Prohibited Area
T1 MODE
-60dB 1 10 100 1K FREQUENCY (Hz) 10K 100K
Figure 10-13. Jitter Attenuation (E1 Mode)
0
JITTER ATTENUATION (dB)
TBR12 Prohibited Area ITU G.7XX Prohibited Area
-20
-40
E1 MODE
-60 1 10 100 1k FREQUENCY (Hz) 10k 100k
107 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-14. Optional Crystal Connections
XTALD
1.544MHz/2.048MHz
MCLK C1 C2
NOTE: C1 AND C2 SHOULD BE 5pF LOWER THAN TWO TIMES THE NOMINAL LOADING CAPACITANCE OF THE CRYSTAL TO ADJUST FOR THE INPUT CAPACITANCE OF THE DEVICE.
10.26 T1/E1/J1 TRANSCEIVER BERT FUNCTION
The BERT block can generate and detect pseudorandom and repeating bit patterns. It is used to test and stress data communication links, and it is capable of generating and detecting the following patterns:

The pseudorandom patterns 2E7, 2E11, 2E15, and QRSS A repetitive pattern from 1 to 32 bits in length Alternating (16-bit) words that flip every 1 to 256 words Daly pattern
The BERT receiver has a 32-bit bit counter and a 24-bit error counter. The BERT receiver reports three events: a change in receive synchronizer status, a bit error being detected, and if either the bit counter or the error counter overflows. Each of these events can be masked within the BERT function through the BERT control register 1 (TR.BC1). If the software detects that the BERT has reported an event, then the software must read the BERT information register (BIR) to determine which event(s) has occurred. To activate the BERT block, the host must configure the BERT mux through the TR.BIC register.
10.26.1 BERT Status
TR.SR9 contains the status information on the BERT function. The host can be alerted through this register when there is a BERT change-of-state. A major change-of-state is defined as either a change in the receive synchronization (i.e., the BERT has gone into or out of receive synchronization), a bit error has been detected, or an overflow has occurred in either the bit counter or the error counter. The host must read status register 9 (TR.SR9) to determine the change-of-state.
10.26.2 BERT Mapping
The BERT function can be assigned to the network direction or backplane direction through the direction control bit in the BIC register (TR.BIC.1). See Figure 10-15 and Figure 10-16. The BERT also can be assigned on a perchannel basis. The BERT transmit control selector (BTCS) and BERT receive control selector (BRCS) bits of the per-channel pointer register (TR.PCPR) are used to map the BERT function into time slots of the transmit and receive data streams. In T1 mode, the user can enable mapping into the F-bit position for the transmit and receive directions through the RFUS and TFUS bits in the BERT interface control (TR.BIC) register.
108 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-15. Simplified Diagram of BERT in Network Direction
FROM RECEIVE FRAMER PER-CHANNEL AND F-BIT (T1 MODE) MAPPING
TO RECEIVE SYSTEM BACKPLANE INTERFACE
BERT RECEIVER 1 0
BERT TRANSMITTER
TO TRANSMIT FRAMER
FROM TRANSMIT SYSTEM BACKPLANE INTERFACE
Figure 10-16. Simplified Diagram of BERT in Backplane Direction
FROM RECEIVE FRAMER
0 1
TO RECEIVE SYSTEM BACKPLANE INTERFACE
PER-CHANNEL AND F-BIT (T1 MODE) MAPPING BERT RECEIVER TO TRANSMIT FRAMER BERT TRANSMITTER FROM TRANSMIT SYSTEM BACKPLANE INTERFACE
109 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.26.3 BERT Repetitive Pattern Set
These registers must be properly loaded for the BERT to generate and synchronize to a repetitive pattern, a pseudorandom pattern, alternating word pattern, or a Daly pattern. For a repetitive pattern that is fewer than 32 bits, the pattern should be repeated so that all 32 bits are used to describe the pattern. For example, if the pattern was the repeating 5-bit pattern ...01101... (where the rightmost bit is the one sent first and received first), then TR.BRP1 should be loaded with ADh, TR.BRP2 with B5h, TR.BRP3 with D6h, and TR.BRP4 with 5Ah. For a pseudorandom pattern, all four registers should be loaded with all 1s (i.e., FFh). For an alternating word pattern, one word should be placed into TR.BRP1 and TR.BRP2 and the other word should be placed into TR.BRP3 and TR.BRP4. For example, if the DDS stress pattern "7E" is to be described, the user would place 00h in TR.BRP1, 00h in TR.BRP2, 7Eh in TR.BRP3, and 7Eh in TR.BRP4 and the alternating word counter would be set to 50 (decimal) to allow 100 bytes of 00h followed by 100 bytes of 7Eh to be sent and received.
10.26.4 BERT Bit Counter
The BERT Bit Counter is comprised of TR.BBC1, TR.BBC2, TR.BBC3, and TR.BBC4. Once BERT has achieved synchronization, this 32-bit counter increments for each data bit (i.e., clock) received. Toggling the LC control bit in TR.BC1 can clear this counter. This counter saturates when full and sets the BBCO status bit.
10.26.5 BERT Error Counter
The BERT Error Counter is comprised of TR.BEC1, TR.BEC2, and TR.BEC3. Once BERT has achieved synchronization, this 24-bit counter increments for each data bit received in error. Toggling the LC control bit in TR.BC1 can clear this counter. This counter saturates when full and sets the BECO status bit.
10.26.6 BERT Alternating Word-Count Rate
When the BERT is programmed in the alternating word mode, each word repeats for the count loaded into TR.BAWC. One word should be placed into TR.BRP1 and TR.BRP2 and the other word should be placed into TR.BRP3 and TR.BRP4.
110 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.27 Payload Error-Insertion Function (T1 Mode Only)
An error-insertion function is available in the transceiver and is used to create errors in the payload portion of the T1 frame in the transmit path. This function is only available in T1 mode. Errors can be inserted over the entire frame or the user can select which channels are to be corrupted. Errors are created by inverting the last bit in the count sequence. For example, if the error rate 1 in 16 is selected, the 16th bit is inverted. F-bits are excluded from the count and are never corrupted. Error rate changes occur on frame boundaries. Error-insertion options include continuous and absolute number with both options supporting selectable insertion rates.
Table 10-14. Transmit Error-Insertion Setup Sequence
STEP 1 2A or 2B ACTION Enter desired error rate in the TR.ERC register. Note: If TR.ER3 through TR.ER0 = 0, no errors are generated even if the constant error-insertion feature is enabled. For constant error insertion, set CE = 1 (TR.ERC.4). For a defined number of errors: - Set CE = 0 (TR.ERC.4) - Load TR.NOE1 and TR.NOE2 with the number of errors to be inserted - Toggle WNOE (TR.ERC.7) from 0 to 1 to begin error insertion
10.27.1 Number-of-Errors Registers
The number-of-error registers determine how many errors are generated. Up to 1023 errors can be generated. The host loads the number of errors to be generated into the TR.NOE1 and TR.NOE2 registers. The host can also update the number of errors to be created by first loading the prescribed value into the TR.NOE registers and then toggling the WNOE bit in the error-rate control registers.
Table 10-15. Error Insertion Examples
VALUE 000h 001h 002h 3FFh WRITE Do not create any errors Create a single error Create two errors Create 1023 errors READ No errors left to be inserted One error left to be inserted Two errors left to be inserted 1023 errors left to be inserted
111 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.28 Programmable Backplane Clock Synthesizer
The transceiver contains an on-chip clock synthesizer that generates a user-selectable clock output on the BPCLK pin, referenced to the recovered receive clock (RCLKO). The synthesizer uses a phase-locked loop to generate low-jitter clocks. Common applications include generation of port and backplane system clocks. The TR.CCR2 register is used to enable (TR.CCR2.0) and select (TR.CCR2.1 and TR.CCR2.2) the clock frequency of the BPCLK pin.
10.29 Fractional T1/E1 Support
The transceiver can be programmed to output gapped clocks for selected channels in the receive and transmit paths to simplify connections into a USART or LAPD controller in fractional T1/E1 or ISDN-PRI applications. The receive and transmit paths have independent enables. Channel formats supported include 56kbps and 64kbps. This is accomplished by assigning an alternate function to the RCHCLK and TCHCLK pins. Setting TR.CCR3.0 = 1 causes the RCHCLK pin to output a gapped clock as defined by the receive fractional T1/E1 function of the TR.PCPR register. Setting TR.CCR3.2 = 1 causes the TCHCLK pin to output a gapped clock as defined by the transmit fractional T1/E1 function of the TR.PCPR register. TR.CCR3.1 and TR.CCR3.3 can be used to select between 64kbps and 56kbps operation. See Section 10.2 for details about programming the per-channel function. In T1 mode no clock is generated at the F-bit position. When 56kbps mode is selected, the LSB clock in the channel is omitted. Only the seven most significant bits of the channel have clocks.
112 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.30 T1/E1/J1 Transmit Flow Diagrams Figure 10-17. T1/J1 Transmit Flow Diagram
TSER
TSIG
HSIE1-3 through PCPR
Hardware Signaling TX ESTORE
T1 TRANSMIT FLOW DIAGRAM
KEY - PIN - SELECTOR
Off-Chip Connection RDATA From T1_rcv_logic
ESCR.4 TESE
Estore Mux
TESO
- REGISTER
TDATA
LBCR1.1 PLB
TLINK
Payload Loopback
HDLC Engine #1 THMS1 H1TC.4 H1TCS1-3 H1TTSBS HDLC Engine #2
H1TC.4 THMS1
HDLC FDL #1
HDLC Mux #1
H2TC.4 THMS2 TFDL T1TCR2.5 TZSE Tx FDL Zero Stuffer
THMS2 H2TC.4 H2TCS1-3 H2TTSBS
HDLC FDL #2
HDLC Mux #2 Idle Code Array
Idle Code Mux T1TCR1.2 TFDLS FDL Mux TFDL BOC Engine Loop Code
TCICE1-3 Loop Code Gen TLOOP T1CCR1.0
BOCC.0 SBOC
BOC Mux T1CCR1.2 TFM T1TCR2.2 TD4YM T1TCR1.0 TYEL D4 12th Fs Yellow alarm FPS or Ft/Fs insertion
Per-Channel Loopback
PCLR1-3 Software Sig Registers
ESF Yellow Alarm
Software Sig
SSIE1-3
F-bit Mux To FDL Mux To ESF Yellow Mux To FDL Mux
TFPT T1TCR1.5
113 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
From BOC Mux From ESF Yellow Alarm From F-bit Mux
FDL Mux
TFPT T1TCR1.5
ESF Yellow
TFM T1CCR1.2 TYEL T1TCR1.0
CRC Mux BERT Engine D4 bit 2 Yellow Alm TFM T1CCR1.2 TD4YM T1TCR2.2 TYEL T1TCR1.0
TCPT T1TCR1.5
BERT Mux BERTEN BIC.0
TFUS BIC.3 F-bit BTCS1-3 from PCPR
T1TCR2.3 FBCT1 T1TCR2.4 FBCT2 NOEL != 0 ERC.4 CE PEICS1-3
F-bit Corruption Payload error insertion Bit 7 stuffing Pulse Density Enforcer
SSIE1-3 GB7S T1TCR1.3 B7SE T1TCR2.0 TPDV INFO1.6 DS0 Monitor TCM0-4 TDS0SEL.0 - .3 TDSOM
T1CCR1.1 PDE CRC Calculation
T1TCR2.7 B8ZSE T1TCR1.1 TBL
B8ZS Encoding Blue Alarm
IOCR1.0 ODF
Bipolar/ NRZ coding
CCR1.4 ODM
1/2 CLK/ FULL CLK
TPOS
TNEG
114 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-18. E1 Transmit Flow Diagram
TSER TSIG
HSIE1-4 through PCPR
Hardware Signaling
E1 TRANSMIT FLOW DIAGRAM
TX ESTORE
ESCR.4 TESE
Estore Mux
TESO Off-Chip Connection
TDATA
RDATA From E1_rcv_logic LBCR1.1 PLB Payload Loopback Mux HDLC Engine #1 THMS1 H1TC.4 HDLC DS0 Mux #1 HDLC Sa-bit Mux #1 H1TCS1-4 H1TTSBS THMS1 H1TC.4 T1SaBE4T1SaBE8 HDLC Engine #2 HDLC DS0 Mux #2 THMS2 H2TC.4 H2TCS1-4 H2TTSBS THMS2 H2TC.4 T2SaBE4-T2SaBE8 BERT Engine BERT Mux BERTEN (BIC.0) BTCS1-4 Idle Code Array Idle Code MUX TCICE1-4 from PCPR H2TTSBS.4 - H2TTSBS.0 H1TTSBS.4 - H1TTSBS.0
KEY - PIN - SELECTOR - REGISTER
HDLC Sa-bit Mux #2
To Per-Channel Mux
115 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
From Idle Code Mux Per-Channel Loopback TNAF Sa-bit Mux THMS1
H1TC.4
RDATA From E1_rcv_logic PCLR1-4
E1 TRANSMIT FLOW DIAGRAM
THMS2 H2TC.4 TAF/TNAF(non Sa) TFPT E1TCR1.7
TS0 Mux
E1TCR1.4 TSIS
Si-bit Mux Si = CRC4 MF Align Word (Does not overwrite E-bits)
E1TCR1.0 TCRC4
Si/CRC4 Mux Auto Ebit Gen TLINK Mux Auto RA Gen TSiAF TSiNAF TRA TSa4 TSa5 TSa6 TSa7 TSa8
TLINK
E1TCR2.2 AEBE
Sa4S - Sa8S E1TCR2.5 - E1TCR2.7 E1TCR2.8 ARA
TSaCR SSIE1-4 E1TCR1.0 T16S E1TCR1.0 TCRC4
TSaCR Mux TSA1 E1TCR1.3 Software Sig CRC Calculate CRC Recalculate Auto AIS Gen UA1 Gen HDB3 Encoding
TS1-16
TDS0SEL.0 - TDS0SEL.4
TCM0-TCM4
CCR1.6 CRC4R
DS0 Monitor
TDSOM
E1TCR2.1 AAIS E1TCR1.5 TUA1 E1TCR1.2 THDB3
To Bipolar/NRZ coding Mux
116 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11 DEVICE REGISTERS
Ten address lines are used to address the register space. Table 11-1 shows the register map for the DS33R11. The addressable range for the device is 0000h to 08FFh. Each Register Section is 64 bytes deep. Global Registers are preserved for software compatibility with multiport devices. The Serial Interface (Line) Registers are used to configure the serial port and the associated transport protocol. The Ethernet Interface (Subscriber) registers are used to control and observe each of the Ethernet ports. The registers associated with the MAC must be configured through indirect register write /read access due to the architecture of the device. When writing to a register input values for unused bits and registers (those designated with "-") should be zero, as these bits and registers are reserved. When a register is read from, the values of the unused bits and registers should be ignored. A latched status bit is set when an event happens and is cleared when read. The register details are provided in the following tables.
Table 11-1. Register Address Map
MAPPER/ PORT Ethernet Mapper T1/E1/J1 Port 1 CHIP SELECT
CS=0, CST=1 CS=1, CST=0
GLOBAL REGISTERS 0000h- 003Fh --
ARBITER 0040h- 007Fh --
BERT 0080h- 00BFh --
SERIAL INTERFACE 00C0h- 013Fh --
ETHERNET INTERFACE 0140h- 17Fh --
T1/E1/J1 TRANSCEIVER -- 000h-0FFh
117 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1 Register Bit Maps
Table 11-2, Table 11-3, Table 11-4, Table 11-5, Table 11-6, and Table 11-7 contain the registers of the DS33R11. Bits that are reserved are noted with a single dash "-". All registers not listed are reserved and should be initialized with a value of 00h for proper operation, unless otherwise noted.
11.1.1 Global Ethernet Mapper Register Bit Map
Table 11-2. Global Ethernet Mapper Register Bit Map
ADDR Name GL.IDRL 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 20h 21h
GL.IDRH GL.CR1 GL.BLR GL.RTCAL GL.SRCALS GL.LIE GL.LIS GL.SIE GL.SIS GL.TRQIE GL.TRQIS GL.BIE GL.BIS GL.CON1 Reserved Reserved Reserved GL.C1QPR Reserved Reserved Reserved GL.BISTEN GL.BISTPF
BIT 7
ID07 ID15 -
BIT 6
ID06 ID14 -
BIT 5
ID05 ID13 -
BIT 4
ID04 ID12 RLCALS1 LIN1TIE LIN1TIS TQ1IE TQ1IS -
BIT 3
ID03 ID11 C1MRPR -
BIT 2
ID02 ID10 REF_CLKO C1HWPR -
BIT 1
ID01 ID09 INTM REFCLKS C1MHPR BISTDN
BIT 0
ID00 ID08 RST GL.BLC1 TLCALS1 SYSCLS LIN1RIE LIN1RIS SUB1IE SUB1IS RQ1IE RQ1IS BIE BIS LINE0 C1HRPR BISTE BISTPF
Note: 22h-3Fh are reserved.
118 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.2 Arbiter Register Bit Map
Table 11-3. Arbiter Register Bit Map
ADDR NAME AR.RQSC1 40h 41h
AR.TQSC1
BIT 7
RQSC7 TQSC7
BIT 6
RQSC6 TQSC6
BIT 5
RQSC5 TQSC5
BIT 4
RQSC4 TQSC4
BIT 3
RQSC3 TQSC3
BIT 2
RQSC2 TQSC2
BIT 1
RQSC1 TQSC1
BIT 0
RQSC0 TQSC0
11.1.3 BERT Register Bit Map
Table 11-4. BERT Register Bit Map
ADDR 080h 081h 082h 083h 084h 085h 086h 087h 088h 08Ah 08Bh 08Ch 08Dh 08Eh 08Fh 90h 91h 92h 93h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh NAME
BCR Reserved BPCLR BPCHR BSPB0R BSPB1R BSPB2R BSPB3R TEICR Reserved Reserved BSR Reserved BSRL Reserved BSRIE Reserved Reserved Reserved RBECB0R RBECB1R RBECB2R Reserved RBCB0 RBCB1 RBCB2 RBCB3 Reserved Reserved Reserved Reserved
BIT 7
BSP7 BSP15 BSP23 BSP31 BEC7 BEC15 BEC23 BC7 BC15 BC23 BC31 -
BIT 6
PMU QRSS BSP6 BSP14 BSP22 BSP30 BEC6 BEC14 BEC22 BC6 BC14 BC22 BC30 -
BIT 5
RNPL PTS BSP5 BSP13 BSP21 BSP29 TIER2 BEC5 BEC13 BEC21 BC5 BC13 BC21 BC29 -
BIT 4
RPIC PLF4 PTF4 BSP4 BSP12 BSP20 BSP28 TIER1 BEC4 BEC12 BEC20 BC4 BC12 BC20 BC28 -
BIT 3
MPR PLF3 PTF3 BSP3 BSP11 BSP19 BSP27 TIER0 PMS PMSL PMSIE BEC3 BEC11 BEC19 BC3 BC11 BC19 BC27 -
BIT 2
APRD PLF2 PTF2 BSP2 BSP10 BSP18 BSP26 BEI BEL BEIE BEC2 BEC10 BEC18 BC2 BC10 BC18 BC26 -
BIT 1
TNPL PLF1 PTF1 BSP1 BSP9 BSP17 BSP25 TSEI BEC BECL BECIE BEC1 BEC9 BEC17 BC1 BC9 BC17 BC25 -
BIT 0
TPIC PLF0 PTF0 BSP0 BSP8 BSP16 BSP24 OOS OOSL OOSIE BEC0 BEC8 BEC16 BC0 BC8 BC16 BC24 -
119 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.4 Serial Interface Register Bit Map
Table 11-5. Serial Interface Register Bit Map
ADDR 0C0h 0C1h 0C2h 0C3h 0C4h 0C5h 0C6h 0C7h 0C8h 0C9h 0CAh 0CBh 0CCh 0CDh 0CEh 0CFh 0D0h 0D1h 0D2h 0D3h 0D4h 0D5h 0D6h NAME
LI.TSLCR LI.RSTPD LI.LPBK Reserved LI.TPPCL LI.TIFGC LI.TEPLC LI.TEPHC LI.TPPSR LI.TPPSRL LI.TPPSRIE Reserved LI.TPCR0 LI.TPCR1 LI.TPCR2 Reserved LI.TBCR0 LI.TBCR1 LI.TBCR2 LI.TBCR3 LI.TMEI Reserved LI.THPMUU
BIT 7
TIFG7 TPEN7 MEIMS TPC7 TPC15 TPC23 TBC7 TBC15 TBC23 TBC31 -
BIT 6
TIFG6 TPEN6 TPER6 TPC6 TPC14 TPC22 TBC6 TBC14 TBC22 TBC30 X86TRA6 X86TRC6 TRSAPIH6 TRSAPIL6 CIR6 RMX6 RMX14 RAPL RAPIE RPC6 RPC14 RPC22 RFPC6 RFPC14 RFPC22 RAPC6 RAPC14 RAPC22 -
BIT 5
TFAD TIFG5 TPEN5 TPER5 TPC5 TPC13 TPC21 TBC5 TBC13 TBC21 TBC29 X86TRA5 X86TRC5 TRSAPIH5 TRSAPIL5 CIR5 RFPD RMX5 RMX13 RIPDL RIPDIE RPC5 RPC13 RPC21 RFPC5 RFPC13 RFPC21 RAPC5 RAPC13 RAPC21 -
BIT 4
TF16 TIFG4 TPEN4 TPER4 TPC4 TPC12 TPC20 TBC4 TBC12 TBC20 TBC28 X86TRA4 X86TRC4 TRSAPIH4 TRSAPIL4 CIR4 RF16 RMX4 RMX12 RSPDL RSPDIE RPC4 RPC12 RPC20 RFPC4 RFPC12 RFPC20 RAPC4 RAPC12 RAPC20 -
BIT 3
TIFV TIFG3 TPEN3 TPER3 TPC3 TPC11 TPC19 TBC3 TBC11 TBC19 TBC27 X86TRA3 X86TRC3 TRSAPIH3 TRSAPIL3 CIR3 RFED RMX3 RMX11 RLPDL RLPDIE RPC3 RPC11 RPC19 RFPC3 RFPC11 RFPC19 RAPC3 RAPC11 RAPC19 -
BIT 2
TSD TIFG2 TPEN2 TPER2 TPC2 TPC10 TPC18 TBC2 TBC10 TBC18 TBC26 X86TRA2 X86TRC2 TRSAPIH2 TRSAPIL2 CIR2 RDD RMX2 RMX10 REPC REPCL REPCIE RPC2 RPC10 RPC18 RFPC2 RFPC10 RFPC18 RAPC2 RAPC10 RAPC18 -
BIT 1
RESET TBRE TIFG1 TPEN1 TPER1 TPC1 TPC9 TPC17 TBC1 TBC9 TBC17 TBC25 X86TRA1 X86TRC1 TRSAPIH1 TRSAPIL1 CIR1 RBRE RMX1 RMX9 RAPC RAPCL RAPCIE RPC1 RPC09 RPC17 RFPC1 RFPC9 RFPC17 RAPC1 RAPC9 RAPC17 -
BIT 0
TDENPLT QLP TIFG0 TPEN0 TPER0 TEPF TEPFL TEPFIE TPC0 TPC8 TPC16 TBC0 TBC8 TBC16 TBC24 TMEI TPMUU TPMUS X86ED X86TRA0 X86TRC0 TRSAPIH0 TRSAPIL0 CIR0 RDENPLT RCCE RMX0 RMX8 RSPC RSPCL RSPCIE RPC0 RPC08 RPC16 RFPC0 RFPC8 RFPC16 RAPC0 RAPC8 RAPC16 -
0D7h LI.THPMUS 0D8h LI.TX86EDE 0D9h 0DAh 0DBh 0DCh 0DDh 100h 101h 102h 103h 104h 105h 106h 107h 108h 109h 10Ah 10Ch 10Dh 10Eh 10Fh 110h 111h 112h 113h
LI.TRX86A X86TRA7 LI.TRX8C X86TRC7 LI.TRX86SAPIH TRSAPIH7 LI.TRX86SAPIL TRSAPIL7 LI.CIR CIRE LI.RSLCR LI.RPPCL LI.RMPSCL RMX7 LI.RMPSCH RMX15 LI.RPPSR LI.RPPSRL REPL LI.RPPSRIE REPIE Reserved LI.RPCB0 RPC7 LI.RPCB1 RPC15 LI.RPCB2 RPC23 LI.RFPCB0 LI.RFPCB1 LI.RFPCB2 Reserved LI.RAPCB0 LI.RAPCB1 LI.RAPCB2 Reserved
RFPC7 RFPC15 RFPC23 RAPC7 RAPC15 RAPC23 -
120 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR 114h 115h 116h 118h 119h 11Ah 11Bh 11Ch 11Dh 11Eh 11Fh 120h
NAME
LI.RSPCB0 LI.RSPCB1 LI.RSPCB2 LI.RBC0 LI.RBC1 LI.RBC2 LI.RBC3 LI.RAC0 LI.RAC1 LI.RAC2 LI.RAC3 LI.RHPMUU
BIT 7
RSPC7 RSPC15 RSPC23 RBC7 RBC15 RBC23 RBC31 REBC7 REBC15 REBC23 REBC31 -
BIT 6
RSPC6 RSPC14 RSPC22 RBC6 RBC14 RBC22 RBC30 REBC6 REBC14 REBC22 REBC30 -
BIT 5
RSPC5 RSPC13 RSPC21 RBC5 RBC13 RBC21 RBC29 REBC5 REBC13 REBC21 REBC29 TQLT5 TQHT5 -
BIT 4
RSPC4 RSPC12 RSPC20 RBC4 RBC12 RBC20 RBC28 REBC4 REBC12 REBC20 REBC28 TQLT4 TQHT4 -
BIT 3
RSPC3 RSPC11 RSPC19 RBC3 RBC11 RBC19 RBC27 REBC3 REBC11 REBC19 REBC27 SAPIHNE
SAPINE01IM
BIT 2
RSPC2 RSPC10 RSPC18 RBC2 RBC10 RBC18 RBC26 REBC2 REBC10 REBC18 REBC26 SAPILNE
SAPINEFEIM
BIT 1
RSPC1 RSPC9 RSPC17 RBC1 RBC9 RBC17 RBC25 REBC1 REBC9 REBC17 REBC25 CNE CNE3LIM TQLT1 TQHT1 TQHTIE TQHTLS
BIT 0
RSPC0 RSPC8 RSPC16 RBC0 RBC8 RBC16 RBC24 REBC0 REBC8 REBC16 REBC24 RPMUU RPMUUS ANE ANE4IM TQLT0 TQHT0 TQLTIE TQLTLS
TQLT7 TQLT6 TQHT7 TQHT6 Note: 0DEh-0FFh, 128h-13Fh are reserved.
121h LI.RHPMUS 122h LI.RX86S 123h LI.RX86LSIE 124h LI.TQLT 125h LI.TQHT 126h LI.TQTIE 127h LI.TQCTLS
TQLT3 TQHT3 TFOVFIE TFOVFLS
TQLT2 TQHT2 TQOVFIE TQOVFLS
121 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.5 Ethernet Interface Register Bit Map
Table 11-6. Ethernet Interface Register Bit Map
ADDR 140h 141h 142h 143h 144h 145h 146h 147h 148h 149h 14Ah 14Bh 14Ch 14Eh 14Fh 150h 151h 152h 153h 154h 155h 156h 157h 158h 159h 15Ah 15Bh 15Ch 15Dh 15Eh NAME BIT 7 BIT 6 BIT 5 BIT 4
MACRA4 MACRA12 MACRD4 MACRD12 MACRD20 MACRD28 MACWD4 MACWD12 MACWD20 MACD28 MACAW4 MACAW12 ED CC2 FL4 FL12 DB BF RMPS4 RMPS12 RQLT4 RQHT4 LERR
BIT 3
MACRA3 MACRA11 MACRD3 MACRD11 MACRD19 MACRD27 MACWD3 MACWD11 MACWD19 MACD27 MACAW3 MACAW11 CRCS NCFQ LOC CC1 FL3 FL11 MIIE MCF RMPS3 RMPS11 RQLT3 RQHT3 RFOVFIE RFOVFLS CRCERR
BIT 2
MACRA2 MACRA10 MACRD2 MACRD10 MACRD18 MACRD26 MACWD2 MACWD10 MACWD18 MACD26 MACAW2 MACAW10 H10S TPDFCB NOC CC0 FL2 FL10 FT UF RMPS2 RMPS10 RQLT2 RQHT2 RQVFIE RQOVFLS DBR
BIT 1
MACRA1 MACRA09 MACRD1 MACRD9 MACRD17 MACRD25 MACWD1 MACWD09 MACWD17 MACD25 MACAW1 MACAW9 MCRW ATFLOW TPRHBC LCO FL1 FL9 CS CF RMPS1 RMPS09 RQLT1 RQHT1 RQLTIE RQHTLS MIIER
BIT 0
MACRA0 MACRA08 MACRD0 MACRD8 MACRD16 MACRD24 MACWD0 MACWD08 MACWD16 MACD24 MACAW0 MACAW8 MCS QLP JAME TPRCB FABORT DEF Fl0 Fl8 FTL LE RMPS0 RMPS08 RQLT0 RQHT0 RQHTIE RQLTLS BFR
SU.MACRADL MACRA7 MACRA6 MACRA5 SU.MACRADH MACRA15 MACRA14 MACRA13 SU.MACRD0 MACRD7 MACRD6 MACRD5 SU.MACRD1 MACRD15 MACRD14 MACRD13 SU.MACRD2 MACRD23 MACRD22 MACRD21 SU.MACRD3 MACRD31 MACRD30 MACRD29 SU.MACWD0 MACWD7 MACWD6 MACWD5 SU.MACWD1 MACWD15 MACWD14 MACWD13 SU.MACWD2 MACWD23 MACWD22 MACWD21 SU.MACWD3 MACD31 MACD30 MACD29 SU.MACAWL MACAW 7 MACAW 6 MACAW 5 SU.MACAWH MACAW 15 MACAW 14 MACAW 13 SU.MACRWC RESERVED SU.LPBK SU.GCR SU.TFRC SU.TFSL UR EC LC SU.TFSH PR HBF CC3 SU.RFSB0 FL7 FL6 FL5 SU.RFSB1 RF WT FL13 SU.RFSB2 CRCE SU.RFSB3 MF SU.RMFSRL RMPS7 RMPS6 RMPS5 SU.RMFSRH RMPS15 RMPS14 RMPS13 SU.RQLT RQLT7 RQLT6 RQLT5 SU.RQHT RQHT7 RQHT6 RQHT5 SU.QRIE SU.QCRLS SU.RFRC UCFR CFRR Note: 15Fh-17Fh are reserved.
122 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.6 MAC Register Bit Map
Table 11-7. MAC Indirect Register Bit Map
ADDR 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh 100h 101h 102h 103h 10Ch 10Dh 10Eh 10Fh 110h NAME
SU.MACCR 31:24 23:16 15:8 7:0 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SU.MACMIIA 31:24 23:16 15:8 7:0 SU.MACMIID 31:24 23:16 15:8 7:0 SU.MACFCR 31:24 23:16 15:8 7:0 SU.MMCCTRL 31:24 23:16 15:8 7:0 RESERVED - initialize to FF RESERVED - initialize to FF RESERVED - initialize to FF RESERVED - initialize to FF RESERVED - initialize to FF
BIT 7
Reserved DRO Reserved BOLMT1 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PHYA4 MIIA1 Reserved Reserved MIID15 MIID07 PT15 PT07 Reserved Reserved Reserved Reserved Reserved MXFRM4 Reserved Reserved Reserved Reserved Reserved
BIT 6
Reserved OML1 Reserved BOLMT0 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PHYA3 MIIA0 Reserved Reserved MIID14 MIID06 PT14 PT06 Reserved Reserved Reserved Reserved Reserved MXFRM3 Reserved Reserved Reserved Reserved Reserved
BIT 5
Reserved OML0 Reserved DC Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PHYA2 Reserved Reserved Reserved MIID13 MIID05 PT13 PT05 Reserved Reserved Reserved Reserved MXFRM10 MXFRM2 Reserved Reserved Reserved Reserved Reserved
BIT 4
HDB F LCC Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PHYA1 Reserved Reserved Reserved MIID12 MIID04 PT12 PT04 Reserved Reserved Reserved Reserved MXFRM9 MXFRM1 Reserved Reserved Reserved Reserved Reserved
BIT 3
PS Reserved Reserved TE Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved PHYA0 Reserved Reserved Reserved MIID11 MIID03 PT11 PT03 Reserved Reserved Reserved Reserved MXFRM8 MXFRM0 Reserved Reserved Reserved Reserved Reserved
BIT 2
Reserved Reserved DRTY RE Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved MIIA4 Reserved Reserved Reserved MIID10 MIID02 PT10 PT02 Reserved PCF Reserved Reserved MXFRM7 Reserved Reserved Reserved Reserved Reserved Reserved
BIT 1
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved MIIA3 MIIW Reserved Reserved MIID09 MIID01 PT09 PT01 Reserved FCE Reserved Reserved MXFRM6 Reserved Reserved Reserved Reserved Reserved Reserved
BIT 0
Reserved Reserved ASTP Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved MIIA2 MIIB Reserved Reserved MIID08 MIID00 PT08 PT00 Reserved FCB Reserved Reserved MXFRM5 Reserved Reserved Reserved Reserved Reserved Reserved
123 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR 111h 112h 113h 200h 201h 202h 203h 204h 205h 206h 207h 300h 301h 302h 303h 308h 309h 30Ah 30Bh 30Ch 30Dh 30Eh 30Fh 334h 335h 336h 337h 338h 339h 33Ah 33Bh
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
RESERVED - Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved initialize to FF RESERVED - Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved initialize to FF RESERVED - Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved initialize to FF SU.RxFrmCtr RXFRMC31 RXFRMC30 RXFRMC29 RXFRMC28 RXFRMC27 RXFRMC26 RXFRMC25 RXFRMC24 31:24 23:16 RXFRMC23 RXFRMC22 RXFRMC21 RXFRMC20 RXFRMC19 RXFRMC18 RXFRMC17 RXFRMC16 15:8 RXFRMC15 RXFRMC14 RXFRMC13 RXFRMC12 RXFRMC11 RXFRMC10 RXFRMC9 RXFRMC8 7:0 RXFRMC7 RXFRMC6 RXFRMC5 RXFRMC4 RXFRMC3 RXFRMC2 RXFRMC1 RXFRMC0
SU.RxFrmOKCtr
31:24 23:16 15:8 7:0 SU.TxFrmCtr 23:16 15:8 7:0 SU.TxBytesCtr 23:16 15:8 7:0
RXFRMOK31 RXFRMOK23 RXFRMOK15 RXFRMOK7 TXFRMC31 TXFRMC23 TXFRMC15 TXFRMC7 TXBYTEC31 TXBYTEC23 TXBYTEC15 TXBYTEC7
RXFRMOK30 RXFRMOK22 RXFRMOK14 RXFRMOK6 TXFRMC30 TXFRMC22 TXFRMC14 TXFRMC6 TXBYTEC30 TXBYTEC22 TXBYTEC14 TXBYTEC6
RXFRMOK29 RXFRMOK21 RXFRMOK13 RXFRMOK5 TXFRMC29 TXFRMC21 TXFRMC13 TXFRMC5 TXBYTEC29 TXBYTEC21 TXBYTEC13 TXBYTEC5
RXFRMOK28 RXFRMOK20 RXFRMOK12 RXFRMOK4 TXFRMC28 TXFRMC20 TXFRMC12 TXFRMC4 TXBYTEC28 TXBYTEC20 TXBYTEC12 TXBYTEC4
RXFRMOK27 RXFRMOK19 RXFRMOK11 RXFRMOK3 TXFRMC27 TXFRMC19 TXFRMC11 TXFRMC3 TXBYTEC27 TXBYTEC19 TXBYTEC11 TXBYTEC3
RXFRMOK26 RXFRMOK18 RXFRMOK10 RXFRMOK2 TXFRMC26 TXFRMC18 TXFRMC10 TXFRMC2 TXBYTEC26 TXBYTEC18 TXBYTEC10 TXBYTEC2
RXFRMOK25 RXFRMOK17 RXFRMOK9 RXFRMOK1 TXFRMC25 TXFRMC17 TXFRMC9 TXFRMC1 TXBYTEC25 TXBYTEC17 TXBYTEC9 TXBYTEC1
RXFRMOK24 RXFRMOK16 RXFRMOK8 RXFRMOK0 TXFRMC24 TXFRMC16 TXFRMC8 TXFRMC0 TXBYTEC24 TXBYTEC16 TXBYTEC8
TXBYTEC0 SU.TxBytesOkCtr TXBYTEOK31 TXBYTEOK30 TXBYTEOK29 TXBYTEOK28 TXBYTEOK27 TXBYTEOK26 TXBYTEOK25 TXBYTEOK24
23:16 TXBYTEOK23 TXBYTEOK22 TXBYTEOK21 TXBYTEOK20 TXBYTEOK19 TXBYTEOK18 TXBYTEOK17 TXBYTEOK16 15:8 TXBYTEOK15 TXBYTEOK14 TXBYTEOK13 TXBYTEOK12 TXBYTEOK11 TXBYTEOK10 TXBYTEOK9 TXBYTEOK8 7:0 TXBYTEOK7 TXBYTEOK6 TXBYTEOK5 TXBYTEOK4 TXBYTEOK3 TXBYTEOK2 TXBYTEOK1 TXBYTEOK0 SU.TxFrmUndr TXFRMU31 TXFRMU30 TXFRMU29 TXFRMU28 TXFRMU27 TXFRMU26 TXFRMU25 TXFRMU24 23:16 TXFRMU23 TXFRMU22 TXFRMU21 TXFRMU20 TXFRMU19 TXFRMU18 TXFRMU17 TXFRMU16 15:8 TXFRMU15 TXFRMU14 TXFRMU13 TXFRMU12 TXFRMU11 TXFRMU10 TXFRMU9 TXFRMU8 7:0 TXFRMU7 TXFRMU6 TXFRMU5 TXFRMU4 TXFRMU3 TXFRMU2 TXFRMU1 TXFRMU0
SU.TxBdFrmCtr TXFRMBD31 TXFRMBD23 TXFRMBD15 TXFRMBD7 TXFRMBD30 TXFRMBD22 TXFRMBD14 TXFRMBD6 TXFRMBD29 TXFRMBD21 TXFRMBD13 TXFRMBD5 TXFRMBD28 TXFRMBD20 TXFRMBD12 TXFRMBD4 TXFRMBD27 TXFRMBD19 TXFRMBD11 TXFRMBD3 TXFRMBD26 TXFRMBD18 TXFRMBD10 TXFRMBD2 TXFRMBD25 TXFRMBD17 TXFRMBD9 TXFRMBD1 TXFRMBD24 TXFRMBD16 TXFRMBD8 TXFRMBD0
23:16 15:8 7:0
Note that the addresses in the table above are the indirect addresses that must be provided to the SU.MACAWH and SU.MACAWL. All unused and reserved locations must be initialized to zero for proper operation.
124 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 11-8. T1/E1/J1 Transceiver Register Bit Map (Active when CST = 0)
ADDR 000h 001h 002h 003h 004h 005h 006h 007h 008h 009h 00Ah 00Bh 00Ch 00Dh 00Eh 00Fh 010h 011h 012h 013h 014h 015h 016h 017h 018h 019h 01Ah 01Bh 01Ch 01Dh 01Eh 01Fh 020h 021h 022h 023h 024h 025h 026h 027h 028h 029h 02Ah 02Bh 02Ch 02Dh 02Eh 02Fh 030h 031h NAME
TR.MSTRREG TR.IOCR1 TR.IOCR2 TR.T1RCR1 TR.T1RCR2 TR.T1TCR1 TR.T1TCR2 TR.T1CCR1 TR.SSIE1-T1 TR.SSIE1-E1 TR.SSIE2-T1 TR.SSIE2-E1 TR.SSIE3-T1 TR.SSIE3-E1 TR.SSIE4 TR.T1RDMR1 TR.T1RDMR2 TR.T1RDMR3 TR.IDR TR.INFO1 TR.INFO2 TR.INFO3 Reserved TR.IIR1 TR.IIR2 TR.SR1 TR.IMR1 TR.SR2 TR.IMR2 TR.SR3 TR.IMR3 TR.SR4 TR.IMR4 TR.SR5 TR.IMR5 TR.SR6 TR.IMR6 TR.SR7 TR.IMR7 TR.SR8 TR.IMR8 TR.SR9 TR.IMR9 TR.PCPR TR.PCDR1 TR.PCDR2 TR.PCDR3 TR.PCDR4 TR.INFO4 TR.INFO5 TR.INFO6 TR.INFO7 TR.H1RC
BIT 7
BIT 6
BIT 5
-- RSMS1 RSYNCINV OOF1 RB8ZS TCPT TZSE -- CH6 CH5 CH14 CH13 CH22 CH20 CH28 CH6 CH14 CH22 ID5 COFA TCLE -- -- SR6 -- RSCOS RSCOS FRCLC FRCLC LUP LUP RSA0 RSA0 TESF TESF RPE RPE RPE RPE BOCC BOCC BBCO BBCO RFCS CH6 CH14 CH22 CH30 -- TEMPTY TEMPTY CSC3 --
BIT 4
-- RSIO TSYNCINV OOF2 RSLC96 TSSE FBCT2 TRAI-CI CH5 CH4 CH13 CH12 CH21 CH19 CH27 CH5 CH13 CH21 ID4 8ZD TOCD -- -- SR5 -- JALT JALT RLOSC RLOSC LOTC LOTC TMF TMF TESEM TESEM RPS RPS RPS RPS RFDLAD RFDLAD BEC0 BEC0 BRCS CH5 CH13 CH21 CH29 -- TFULL TFULL CSC2 --
BIT 3
TEST1 TSDW TSSYNCINV SYNCC RZSE GB7S FBCT1 TAIS-CI CH4 CH3 CH12 CH11 CH20 CH18 CH26 CH4 CH12 CH20 ID3 16ZD RL3 -- -- SR4 -- LRCL LRCL RYEL RYEL LORC LORC TAF TAF TSLIP TSLIP RHWM RHWM RHWM RHWM RFDLF RFDLF BRA1 BRA1 THSCS CH4 CH12 CH20 CH28 H2UDR REMPTY REMPTY CSC0 HDLCD
BIT 2
TEST0 TSM H100EN SYNCT -- TFDLS TD4YM TFM CH3 CH2 CH11 CH10 CH19 CH17 CH25 CH3 CH11 CH19 ID2 SEFE RL2 CRCRC -- SR3 -- TCLE TCLE RUA1 RUA1 V52LNK V52LNK RMF RMF RESF RESF RNE RNE RNE RNE TFDLE TFDLE BRA0 BRA0 PEICS CH3 CH11 CH19 CH27 H2OBT PS2 PS2 FASSA --
BIT 1
T1/E1 TSIO TSCLKM SYNCE RJC TBL Reserved PDE CH2 CH1 CH10 CH9 CH18 CH16 CH24 CH2 CH10 CH18 ID1 B8ZS RL1 FASRC -- SR2 -- TOCD TOCD FRCL FRCL RDMA RDMA RCMF RCMF RESEM RESEM TLWM TLWM TLWM TLWM RMTCH RMTCH BRLOS BRLOS TFCS CH2 CH10 CH18 CH26 H1UDR PS1 PS1 CASSA --
BIT 0
SFTRST ODF RSCLKM RESYNC RD4YM TYEL TB7ZS TLOOP CH1 UCAW CH9 CH8 CH17 LCAW CH23 CH1 CH9 CH17 ID0 FBE RL0 CASRC -- SR1 SR9 LOLITC LOLITC RLOS RLOS RRA RRA RAF RAF RSLIP RSLIP TNF TNF TNF TNF RBOC RBOC BSYNC BSYNC BTCS CH1 CH9 CH17 CH25 H1OBT PS0 PS0 CRC4SA RSFD
-- -- RSMS RSMS2 RDCLKINV TDCLKINV -- ARC -- RFM TJC TFPT TB8ZS TSLC96 -- -- CH8 CH7 CH6 CH7 CH16 CH15 CH15 CH14 CH24 CH23 CH22 CH21 CH30 CH29 CH8 CH7 CH16 CH15 CH24 CH23 ID7 ID6 RPDV TPDV BSYNC BD -- -- -- -- SR8 SR7 -- -- ILUT TIMER ILUT TIMER RYELC RUA1C RYELC RUA1C LSPARE LDN LSPARE LDN RAIS-CI RSA1 RAIS-CI RSA1 -- -- -- -- -- TMEND -- TMEND -- TMEND -- TMEND -- -- -- -- -- BBED -- BBED RSAOICS RSRCS CH8 CH7 CH16 CH15 CH24 CH23 CH32 CH31 -- -- -- -- -- -- CSC5 CSC4 RHR RHMS
125 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR 032h 033h 034h 035h 036h 037h 038h 039h 03Ah 03Bh 03Ch 03Dh 03Eh 03Fh 040h 041h 042h 043h 044h 045h 046h 047h 048h 049h 04Ah 04Bh 04Ch 04Dh 04Eh 04Fh 050h 051h 052h 053h 054h 055h 056h 057h 058h 059h
NAME
TR.H2RC TR.E1RCR1 TR.E1RCR2 TR.E1TCR1 TR.E1TCR2 TR.BOCC TR.RSINFO1 TR.RSINFO2 TR.RSINFO3 TR.RSINFO4 TR.RSCSE1 TR.RSCSE2 TR.RSCSE3 TR.RSCSE4 TR.SIGCR TR.ERCNT TR.LCVCR1 TR.LCVCR2 TR.PCVCR1 TR.PCVCR2 TR.FOSCR1 TR.FOSCR2 TR.EBCR1 TR.EBCR2 TR.LBCR TR.PCLR1 TR.PCLR2 TR.PCLR3 TR.PCLR4 TR.ESCR TR.TS1 TR.TS2 TR.TS3 TR.TS4 TR.TS5 TR.TS6 TR.TS7 TR.TS8 TR.TS9 TR.TS10
BIT 7
RHR RSERC -- TFPT Reserved -- CH8 CH16 CH24 -- CH8 CH16 CH24 -- GRSRE -- LCVC15 LCVC7 PCVC15 PCVC7 FOS15 FOS7 EB15 EB7 LTS CH8 CH16 CH24 CH32 TESALGN
BIT 6
RHMS RSIGM -- T16S Reserved -- CH7 CH15 CH23 -- CH7 CH15 CH23 -- -- MECU LCVC14 LCVC6 PCVC14 PCVC6 FOS14 FOS6 EB14 EB6 -- CH7 CH15 CH23 CH31 TESR
BIT 5
-- RHDB3 -- TUA1 Reserved -- CH6 CH14 CH22 CH30 CH6 CH14 CH22 CH30 -- ECUS LCVC13 LCVC5 PCVC13 PCVC5 FOS13 FOS5 EB13 EB5 -- CH6 CH14 CH22 CH30 TESMDM
BIT 4
-- RG802 -- TSiS Reserved RBOCE CH5 CH13 CH21 CH29 CH5 CH13 CH21 CH29 RFE EAMS LCVC12 LCVC4 PCVC12 PCVC4 FOS12 FOS4 EB12 EB4 LIUC CH5 CH13 CH21 CH29 TESE
BIT 3
HDLCD RCRC4 -- TSA1 Reserved RBR CH4 CH12 CH20 CH28 CH4 CH12 CH20 CH28 RFF VCRFS LCVC11 LCVC3 PCVC11 PCVC3 FOS11 FOS3 EB11 EB3 LLB CH4 CH12 CH20 CH28 RESALGN
BIT 2
-- FRC -- THDB3 AEBE RBF1 CH3 CH11 CH19 CH27 CH3 CH11 CH19 CH27 RCCS FSBE LCVC10 LCVC2 PCVC10 PCVC2 FOS10 FOS2 EB10 EB2 RLB CH3 CH11 CH19 CH27 RESR
BIT 1
-- SYNCE -- TG802 AAIS RBF0 CH2 CH10 CH18 CH26 CH2 CH10 CH18 CH26 TCCS MOSCRF LCVC9 LCVC1 PCVC9 PCVC1 FOS9 FOS1 EB9 EB1 PLB CH2 CH10 CH18 CH26 RESMDM
BIT 0
RSFD RESYNC RCLA TCRC4 ARA SBOC CH1 CH9 CH17 CH25 CH1 CH9 CH17 CH25 FRSAO LCVCRF LCCV8 LCVC0 PCVC8 PCVC0 FOS8 FOS0 EB8 EB0 FLB CH1 CH9 CH17 CH25 RESE
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
05Ah TR.TS11 05Bh TR.TS12 05Ch TR.TS13 05Dh TR.TS14 05Eh TR.TS15 05Fh 060h 061h
TR.TS16 TR.RS1 TR.RS2
126 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR NAME 062h 063h 064h 065h 066h 067h 068h 069h
TR.RS3 TR.RS4 TR.RS5 TR.RS6 TR.RS7 TR.RS8 TR.RS9 TR.RS10
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition. Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
06Ah TR.RS11 06Bh TR.RS12 06Ch TR.RS13 06Dh TR.RS14 06Eh TR.RS15 06Fh 070h 071h 072h 073h 074h 075h 076h 077h 078h 079h 07Ah 07Bh 07Ch 07Dh 07Eh 07Fh 080h 081h 082h 083h 084h 085h 086h 087h 088h 089h 08Ah 08Bh 08Ch 08Dh 08Eh 08Fh 090h 091h 092h
TR.RS16 TR.CCR1 TR.CCR2 TR.CCR3 TR.CCR4 TR.TDS0SEL TR.TDS0M TR.RDS0SEL TR.RDS0M TR.LIC1 TR.LIC2 TR.LIC3 TR.LIC4 Reserved TR.TLBC TR.IAAR TR.PCICR TR.TCICE1 TR.TCICE2 TR.TCICE3 TR.TCICE4 TR.RCICE1 TR.RCICE2 TR.RCICE3 TR.RCICE4 TR.RCBR1 TR.RCBR2 TR.RCBR3 TR.RCBR4 TR.TCBR1 TR.TCBR2 TR.TCBR3 TR.TCBR4 TR.H1TC TR.H1FC TR.H1RCS1
-- -- -- RLT3 -- B1 -- B1 L2 ETS -- CMIE -- -- GRIC C7 CH8 CH16 CH24 CH32 CH8 CH16 CH24 CH32 CH8 CH16 CH24 CH32 CH8 CH16 CH24 CH32 NOFS -- RHCS8
CRC4R -- -- RLT2 -- B2 -- B2 L1 LIRST TCES CMII -- AGCD GTIC C6 CH7 CH15 CH23 CH31 CH7 CH15 CH23 CH31 CH7 CH15 CH23 CH31 CH7 CH15 CH23 CH31 TEOML -- RHCS7
SIE -- -- RLT1 -- B3 -- B3 L0 IBPV RCES MPS1 -- GC5 IAA5 C5 CH6 CH14 CH22 CH30 CH6 CH14 CH22 CH30 CH6 CH14 CH22 CH30 CH6 CH14 CH22 CH30 THR TFLWM2 RHCS6
ODM -- -- RLT0 TCM4 B4 RCM4 B4 EGL TUA1 MM1 MPS0 -- GC4 IAA4 C4 CH5 CH13 CH21 CH29 CH5 CH13 CH21 CH29 CH5 CH13 CH21 CH29 CH5 CH13 CH21 CH29 THMS TFLWM1 RHCS5
-- -- TDATFMT UOP3 TCM3 B5 RCM3 B5 JAS JAMUX MM0 TT1 -- GC3 IAA3 C3 CH4 CH12 CH20 CH28 CH4 CH12 CH20 CH28 CH4 CH12 CH20 CH28 CH4 CH12 CH20 CH28 TFS TFLWM0 RHCS4
TCSS1 BPCS1 TGPCKEN UOP2 TCM2 B6 RCM2 B6 JABDS -- RSCLKE TT0 -- GC2 IAA2 C2 CH3 CH11 CH19 CH27 CH3 CH11 CH19 CH27 CH3 CH11 CH19 CH27 CH3 CH11 CH19 CH27 TEOM RFHWM2 RHCS3
TCSS0 BPCS0 RDATFMT UOP1 TCM1 B7 RCM1 B7 DJA SCLD TSCLKE RT1 -- GC1 IAA1 C1 CH2 CH10 CH18 CH26 CH2 CH10 CH18 CH26 CH2 CH10 CH18 CH26 CH2 CH10 CH18 CH26 TZSD RFHWM1 RHCS2
RLOSF BPEN RGPCKEN UOP0 TCM0 B8 RCM0 B8 TPD CLDS TAOZ RT0 -- GC0 IAA0 C0 CH1 CH9 CH17 CH25 CH1 CH9 CH17 CH25 CH1 CH9 CH17 CH25 CH1 CH9 CH17 CH25 TCRCD RFHWM0 RHCS1
127 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR 093h 094h 095h 096h 097h 098h 099h 09Ah 09Bh 09Ch 09Dh 09Eh 09Fh 0A0h 0A1h 0A2h 0A3h 0A4h 0A5h 0A6h 0A7h 0A8h 0A9h 0AAh 0ABh 0ACh 0ADh 0AEh 0AFh 0B6h 0B7h 0B8h 0B9h 0BAh 0BBh 0BCh 0BDh 0BEh 0BFh 0C0h 0C1h 0C2h 0C3h 0C3h 0C5h 0C6h 0C7h 0C8h 0C9h 0CAh 0CBh 0CCh 0CDh 0CEh
NAME
TR.H1RCS2 TR.H1RCS3 TR.H1RCS4 TR.H1RTSBS TR.H1TCS1 TR.H1TCS2 TR.H1TCS3 TR.H1TCS4 TR.H1TTSBS TR.H1RPBA TR.H1TF TR.H1RF TR.H1TFBA TR.H2TC TR.H2FC TR.H2RCS1 TR.H2RCS2 TR.H2RCS3 TR.H2RCS4 TR.H2RTSBS TR.H2TCS1 TR.H2TCS2 TR.H2TCS3 TR.H2TCS4 TR.H2TTSBS TR.H2RPBA TR.H2TF TR.H2RF TR.H2TFBA TR.IBCC TR.TCD1 TR.TCD2 TR.RUPCD1 TR.RUPCD2 TR.RDNCD1 TR.RDNCD2 TR.RSCC TR.RSCD1 TR.RSCD2 TR.RFDL TR.TFDL TR.RFDLM1 TR.RFDLM2 Reserved Reserved TR.RAF TR.RNAF TR.RSiAF TR.RSiNAF TR.RRA TR.RSa4 TR.RSa5 TR.RSa6 TR.RSa7
BIT 7
RHCS16 RHCS24 RHCS32 RCB8SE THCS8 THCS16 THCS24 THCS32 TCB8SE MS THD7 RHD7 TFBA7 NOFS -- RHCS8 RHCS16 RHCS24 RHCS32 RCB8SE THCS8 THCS16 THCS24 THCS32 TCB8SE MS THD7 RHD7 TFBA7 TC1 C7 C7 C7 C7 C7 C7 -- C7 C7 TFDL7 RFDLM7 RFDLM7 -- -- Si Si SiF0 SiF1 RRAF1 RSa4F1 RSa5F1 RSa6F1 RSa7F1
BIT 6
RHCS15 RHCS23 RHCS31 RCB7SE THCS7 THCS15 THCS23 THCS31 TCB7SE RPBA6 THD6 RHD6 TFBA6 TEOML -- RHCS7 RHCS15 RHCS23 RHCS31 RCB7SE THCS7 THCS15 THCS23 THCS31 TCB7SE RPBA6 THD6 RHD6 TFBA6 TC0 C6 C6 C6 C6 C6 C6 -- C6 C6 TFDL6 RFDLM6 RFDLM6 -- -- 0 1 SiF2 SiF3 RRAF3 RSa4F3 RSa5F3 RSa6F3 RSa7F3
BIT 5
RHCS14 RHCS22 RHCS30 RCB6SE THCS6 THCS14 THCS22 THCS30 TCB6SE RPBA5 THD5 RHD5 TFBA5 THR TFLWM2 RHCS6 RHCS14 RHCS22 RHCS30 RCB6SE THCS6 THCS14 THCS22 THCS30 TCB6SE RPBA5 THD5 RHD5 TFBA5 RUP2 C5 C5 C5 C5 C5 C5 -- C5 C5 TFDL5 RFDLM5 RFDLM5 -- -- 0 A SiF4 SiF5 RRAF5 RSa4F5 RSa5F5 RSa6F5 RSa7F5
BIT 4
RHCS13 RHCS21 RHCS29 RCB5SE THCS5 THCS13 THCS21 THCS29 TCB5SE RPBA4 THD4 RHD4 TFBA4 THMS TFLWM1 RHCS5 RHCS13 RHCS21 RHCS29 RCB5SE THCS5 THCS13 THCS21 THCS29 TCB5SE RPBA4 THD4 RHD4 TFBA4 RUP1 C4 C4 C4 C4 C4 C4 -- C4 C4 TFDL4 RFDLM4 RFDLM4 -- -- 1 Sa4 SiF6 SiF7 RRAF7 RSa4F7 RSa5F7 RSa6F7 RSa7F7
BIT 3
RHCS12 RHCS20 RHCS28 RCB4SE THCS4 THCS12 THCS20 THCS28 TCB4SE RPBA3 THD3 RHD3 TFBA3 TFS TFLWM0 RHCS4 RHCS12 RHCS20 RHCS28 RCB4SE THCS4 THCS12 THCS20 THCS28 TCB4SE RPBA3 THD3 RHD3 TFBA3 RUP0 C3 C3 C3 C3 C3 C3 -- C3 C3 TFDL3 RFDLM3 RFDLM3 -- -- 1 Sa5 SiF8 SiF9 RRAF9 RSa4F9 RSa5F9 RSa6F9 RSa7F9
BIT 2
RHCS11 RHCS19 RHCS27 RCB3SE THCS3 THCS11 THCS19 THCS27 TCB3SE RPBA2 THD2 RHD2 TFBA2 TEOM RFHWM2 RHCS3 RHCS11 RHCS19 RHCS27 RCB3SE THCS3 THCS11 THCS19 THCS27 TCB3SE RPBA2 THD2 RHD2 TFBA2 RDN2 C2 C2 C2 C2 C2 C2 RSC2 C2 C2 TFDL2 RFDLM2 RFDLM2 -- -- 0 Sa6 SiF10 SiF11 RRAF11 RSa4F11 RSa5F11 RSa6F11 RSa7F11
BIT 1
RHCS10 RHCS18 RHCS26 RCB2SE THCS2 THCS10 THCS18 THCS26 TCB2SE RPBA1 THD1 RHD1 TFBA1 TZSD RFHWM1 RHCS2 RHCS10 RHCS18 RHCS26 RCB2SE THCS2 THCS10 THCS18 THCS26 TCB2SE RPBA1 THD1 RHD1 TFBA1 RDN1 C1 C1 C1 C1 C1 C1 RSC1 C1 C1 TFDL1 RFDLM1 RFDLM1 -- -- 1 Sa7 SiF12 SiF13 RRAF13 RSa4F13 RSa5F13 RSa6F13 RSa7F13
BIT 0
RHCS9 RHCS17 RHCS25 RCB1SE THCS1 THCS9 THCS17 THCS25 TCB1SE RPBA0 THD0 RHD0 TFBA0 TCRCD RFHWM0 RHCS1 RHCS9 RHCS17 RHCS25 RCB1SE THCS1 THCS9 THCS17 THCS25 TCB1SE RPBA0 THD0 RHD0 TFBA0 RDN0 C0 C0 C0 C0 C0 C0 RSC0 C0 C0 TFDL0 RFDLM0 RFDLM0 -- -- 1 Sa8 SiF14 SiF15 RRAF15 RSa4F15 RSa5F15 RSa6F15 RSa7F15
Bit Definitions Change With BOCC Setting. See Register Definition.
128 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR 0CFh 0D0h 0D1h 0D2h 0D3h 0D4h 0D5h 0D6h 0D7h 0D8h 0D9h 0DAh 0DBh 0DCh 0DDh 0DEh 0DFh 0E0h 0E1h 0E2h 0E3h 0E4h 0E5h 0E6h 0E7h 0E8h 0E9h 0EAh 0EBh 0ECh 0EDh 0EEh 0EFh
NAME
TR.RSa8 TR.TAF TR.TNAF TR.TSiAF TR.TSiNAF TR.TRA TR.TSa4 TR.TSa5 TR.TSa6 TR.TSa7 TR.TSa8 TR.TSACR TR.BAWC TR.BRP1 TR.BRP2 TR.BRP3 TR.BRP4 TR.BC1 TR.BC2 Reserved TR.BBC1 TR.BBC2 TR.BBC3 TR.BBC4 TR.BEC1 TR.BEC2 TR.BEC3 TR.BIC TR.ERC TR.NOE1 TR.NOE2 TR.NOEL1 TR.NOEL2
BIT 7
RSa8F1 Si Si TsiF0 TsiF1 TRAF1 TSa4F1 TSa5F1 TSa6F1 TSa7F1 TSa8F1 SiAF ACNT7 RPAT7 RPAT15 RPAT23 RPAT31 TC EIB2 -- BBC7 BBC15 BBC23 BBC31 EC7 EC15 EC23 -- WNOE C7 -- C7 --
BIT 6
RSa8F3 0 1 TsiF2 TsiF3 TRAF3 TSa4F3 TSa5F3 TSa6F3 TSa7F3 TSa8F3 SiNAF ACNT6 RPAT6 RPAT14 RPAT22 RPAT30 TINV EIB1 -- BBC6 BBC14 BBC22 BBC30 EC6 EC14 EC22 RFUS -- C6 -- C6 --
BIT 5
RSa8F5 0 A TsiF4 TsiF5 TRAF5 TSa4F5 TSa5F5 TSa6F5 TSa7F5 TSa8F5 RA ACNT5 RPAT5 RPAT13 RPAT21 RPAT29 RINV EIB0 -- BBC5 BBC13 BBC21 BBC29 EC5 EC13 EC21 -- -- C5 -- C5 --
BIT 4
RSa8F7 1 Sa4 TsiF6 TsiF7 TRAF7 TSa4F7 TSa5F7 TSa6F7 TSa7F7 TSa8F7 Sa4 ACNT4 RPAT4 RPAT12 RPAT20 RPAT28 PS2 SBE -- BBC4 BBC12 BBC20 BBC28 EC4 EC12 EC20 TBAT CE C4 -- C4 --
BIT 3
RSa8F9 1 Sa5 TsiF8 TsiF9 TRAF9 TSa4F9 TSa5F9 TSa6F9 TSa7F9 TSa8F9 Sa5 ACNT3 RPAT3 RPAT11 RPAT19 RPAT27 PS1 RPL3 -- BBC3 BBC11 BBC19 BBC27 EC3 EC11 EC19 TFUS ER3 C3 -- C3 --
BIT 2
RSa8F11 0 Sa6 TsiF10 TsiF11 TRAF11 TSa4F11 TSa5F11 TSa6F11 TSa7F11 TSa8F11 Sa6 ACNT2 RPAT2 RPAT10 RPAT18 RPAT26 PS0 RPL2 -- BBC2 BBC10 BBC18 BBC26 EC2 EC10 EC18 -- ER2 C2 -- C2 --
BIT 1
RSa8F13 1 Sa7 TsiF12 TsiF13 TRAF13 TSa4F13 TSa5F13 TSa6F13 TSa7F13 TSa8F13 Sa7 ACNT1 RPAT1 RPAT9 RPAT17 RPAT25 LC RPL1 -- BBC1 BBC9 BBC17 BBC25 EC1 EC9 EC17 BERTDIR ER1 C1 C9 C1 C9
BIT 0
RSa8F15 1 Sa8 TsiF14 TSiF15 TRAF15 TSa4F15 TSa5F15 TSa6F15 TSa7F15 TSa8F15 Sa8 ACNT0 RPAT0 RPAT8 RPAT16 RPAT24 RESYNC RPL0 -- BBC0 BBC8 BBC16 BBC24 EC0 EC8 EC16 BERTEN ER0 C0 C8 C0 C8
129 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.2 Global Register Definitions for Ethernet Mapper
Functions contained in the global registers include: framer reset, LIU reset, device ID, and BERT interrupt status. These registers are preserved to provide code compatibility with the multiport devices in this product family. The global registers bit descriptions are presented below.
Register Name: Register Description: Register Address: Bit # Name Default 7 ID07 0 6 ID06 0
GL.IDRL Global ID Low Register 00h 5 ID05 1 4 ID04 1 3 ID03 0 2 ID02 0 1 ID01 0 0 ID00 0
Bit 7: ID07 Reserved for future use Bit 6: ID06 Reserved for future use Bit 5: ID05 If this bit is set the device contains a RMII interface Bit 4: ID04 If this bit is set the device contains a MII interface Bit 3: ID03 If this bit is set the device contains an Ethernet PHY Bits 0-2: ID00-ID02 A three-bit count that is equal to 000b for the first die revision, and is incremented with each successive die revision. May not match the two-letter die revision code on the top brand of the device.
Register Name: Register Description: Register Address: Bit # Name Default 7 ID15 0 6 ID14 0
GL.IDRH Global ID High Register 01h 5 ID13 0 4 ID12 0 3 ID11 0 2 ID10 0 1 ID09 1 0 ID08 0
Bits 5-7: ID13-15 Number of Ethernet ports in the device minus 1. (i.e. 000 = 1 Ethernet port) Bit 4: ID12 If this bit is set the device has LIU functionality Bit 3: ID11 If this bit is set the device has a framer Bit 2: ID10 Reserved for future use Bit 1: ID09 If this bit is set the device has HDLC or X.86 encapsulation Bit 0: ID08 If this bit is set the device has inverse multiplexing functionality
130 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 6 GL.CR1 Global Control Register 1 02h 5 4 3 2 REF_CLKO 0 1 INTM 0 0 RST 0
Bit 2: REF_CLKO OFF (REF_CLKO) This bit determines if the REF_CLKO is turned off 1 = REF_CLKO is disabled and outputs an active low signal. 0 = REF_CLKO is active and in accordance with RMII/MII Selection Bit 1: INT pin mode (INTM) This bit determines the inactive mode of the INT pin. The INT pin always drives low when active. 1 = Pin is high impedance when not active 0 = Pin drives high when not active Bit 0: Reset (RST). When this bit is set to 1, all of the internal data path and status and control registers (except this RST bit), on all ports, are reset to their default state. This bit must be set high for a minimum of 100ns. 0 = Normal operation 1 = Reset and force all internal registers to their default values Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.BLR Global BERT Connect Register 03h 5 0 4 0 3 0 2 0 1 0 0 BLC1 0
Bit 0: BERT Connect 1 (BLC1) If this bit is set to 1, the BERT is connected to Serial Interface 1. The BERT transmitter is connected to the transmit serial port and receive to receive serial port. When the BERT is connected, normal data transfer is interrupted. Note that connecting the BERT overrides a connection to the Serial Interface, if a connection exists. When the BERT is disconnected, the connection is restored.
131 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 6 GL.RTCAL Global Receive and Transmit Serial Port Clock Activity Latched Status 04h 5 4 RLCALS1 3 2 1 0 TLCALS1 -
Bit 4: Receive Serial Interface Clock Activity Latched Status 1 (RLCALS1) This bit is set to 1 if the receive clock for Serial Interface 1 has activity. This bit is cleared upon read. Bit 0: Transmit Serial Interface Clock Activity Latched Status 1 (TSCALS1) This bit is set to 1 if the transmit clock for Serial Interface 1 has activity. This bit is cleared upon read. Register Name: Register Description: Register Address: Bit # Name Default 7 GL.SRCALS Global SDRAM Reference Clock Activity Latched Status 05h 6 5 4 3 2 1 REFCLKS 0 SYSCLS -
Bit 1: Reference Clock Activity Latched Status (REFCLKS) This bit is set to 1 if REF_CLK has activity. This bit is cleared upon read. Bit 0: System Clock Input Latched Status (SYSCLS) This bit is set to 1 if SYSCLKI has activity. This bit is cleared upon read.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.LIE Global Serial Interface Interrupt Enable 06h 5 0 4 LIN1TIE 0 3 0 2 0 1 0 0 LIN1RIE 0
Bit 4: Serial Interface 1 TX Interrupt Enable (LINE1TIE) Setting this bit to 1 enables an interrupt on LIN1TIS Bit 0: Serial Interface 1 RX Interrupt Enable (LINE1RIE) Setting this bit to 1 enables an interrupt on LIN1RIS
132 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.LIS Global Serial Interface Interrupt Status 07h 5 0 4 LIN1TIS 0 3 0 2 0 1 0 0 LIN1RIS 0
Bit 4: Serial Interface 1 TX Interrupt Status (LINE1TIS) This bit is set if Serial Interface 1 Transmit has an enabled interrupt generating event. Serial Interface interrupts consist of HDLC interrupts and X.86 interrupts. Bit 0: Serial Interface 1 RX Interrupt Status (LINER1IS) This bit is set if Serial Interface 1 Receive has an enabled interrupt generating event. Serial Interface interrupts consist of HDLC interrupts and X.86 interrupts. Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.SIE Global Ethernet Interface Interrupt Enable 08h 5 0 4 0 3 0 2 0 1 0 0 SUB1IE 0
Bit 0: Ethernet Interface 1 Interrupt Enable (SUB1IE) Setting this bit to 1 enables an interrupt on SUB1S.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.SIS Global Ethernet Interface Interrupt Status 09h 5 0 4 0 3 0 2 0 1 0 0 SUB1IS 0
Bit 0: Ethernet Interface 1 Interrupt Status (SUB1IS) This bit is set to 1 if Ethernet Interface 1 has an enabled interrupt generating event. The Ethernet Interface consists of the MAC and The RMII/MII port.
133 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.TRQIE Global Transmit Receive Queue Interrupt Enable 0Ah 5 0 4 TQ1IE 0 3 0 2 0 1 0 0 RQ1IE 0
Bit 4: Transmit Queue 1 Interrupt Enable (TQ1IE) Setting this bit to 1 enables an interrupt on TQ1IS. Bit 0: Receive Queue 1 Interrupt Enable (RQ1IE) Setting this bit to 1 enables an interrupt on RQ1IS.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.TRQIS Global Transmit Receive Queue Interrupt Status 0Bh 5 0 4 TQ1IS 0 3 0 2 0 1 0 0 RQ1IS 0
Bit 4: Transmit Queue 1 Interrupt Enable (TQ1IS) If this bit is set to 1, the Transmit Queue 1 has interrupt status event. Transmit queue events are transmit queue crossing thresholds and queue overflows. Bit 0: Receive Queue 1 Interrupt Status (RQ1IS) If this bit is set to 1, the Receive Queue 1 has interrupt status event. Receive queue events are transmit queue crossing thresholds and queue overflows.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.BIE Global BERT Interrupt Enable 0Ch 5 0 4 0 3 0 2 0 1 0 0 BIE 0
Bit 0: BERT Interrupt Enable (BIE) Setting this bit to 1 enables an interrupt on BIS.
134 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.BIS Global BERT Interrupt Status 0Dh 5 0 4 0 3 0 2 0 1 0 0 BIS 0
Bit 0: BERT Interrupt Status (BIS) This bit is set to 1 if the BERT has an enabled interrupt generating event.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.CON1 Connection Register for Ethernet Interface 1 0Eh 5 0 4 0 3 0 2 0 1 0 0 LINE1[0] 1
Bit 0: LINE1[0] This bit is preserved to provide software compatibility with multiport devices. The LINE1[0] bit selects the Ethernet port that is to be connected to the Serial Interface. Note that bidirectional connection is assumed between the Serial and Ethernet Interfaces. The connection register and corresponding queue size must be defined for proper operation. Writing a 0 to this register will disconnect the connection. When a connection is disconnected, "1"s are sourced to the Serial Interface transmit and to the HDLC receiver and the clocks to the HDLC transmitter/receiver are disabled.
135 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.C1QPR Connection 1 Queue Pointer Reset 12h 5 0 4 0 3 C1MRPR 0 2 C1HWPR 0 1 C1MHPR 0 0 C1HRPR 0
Bit 3: MAC Read Pointer Reset (C1MRPR) Setting this bit to 1 resets the receive queue read pointer for connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear the bit before subsequent reset operations. Bit 2: HDLC Write Pointer Reset (C1HWPR) Setting this bit to 1 resets the receive queue write pointer for connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear the bit before subsequent reset operations. Bit 1: HDLC Read Pointer Reset (C1MHPR) Setting this bit to 1 resets the transmit queue read pointer for connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear the bit before subsequent reset operations. Bit 0: MAC Transmit Write Pointer Reset (C1HRPR) Setting this bit to 1 resets the transmit queue write pointer for connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear the bit before subsequent reset operations.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.BISTEN BIST Enable 20h 5 0 4 0 3 0 2 0 1 0 0 BISTE 0
Bit 0: BIST Enable (BISTE) If this bit is set the DS33R11 performs BIST test on the SDRAM. Normal data communication is halted while BIST enable is high. The user must reset the DS33R11 after completion of BIST test before normal dataflow can begin.
136 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.BISTPF BIST Pass-Fail 21h 5 0 4 0 3 0 2 0 1 BISTDN 0 0 BISTPF 0
Bit 1: BIST DONE (BISTDN) If this bit is set to 1, the DS33R11 has completed the BIST Test initiated by BISTE. The pass fail result is available in BISTPF. Bit 0: BIST Pass-Fail (BISTPF) This bit is equal to 0 after the DS33R11 performs BIST testing on the SDRAM and the test passes. This bit is set to 1 if the test failed. This bit is valid only after the BIST test is complete and the BIST DN bit is set. If set this bit can only be cleared by resetting the DS33R11.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.SDMODE1 Global SDRAM Mode Register 1 3Ah 5 0 4 0 3 WT 0 2 BL2 0 1 BL1 1 0 BL0 1
Bit 3: Wrap Type (WT) This bit is used to configure the wrap mode. 0 = Sequential 1 = Interleave Bits 0- 2: Burst Length 0 through 2 (BL0 - BL2) These bits are used to determine the Burst Length. Note: This register has a nonzero default value. This should be taken into consideration when initializing the device. Note: After changing the value of this register, the user must toggle the GL.SDMODEWS.SDMW bit to write the new values to the SDRAM.
137 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 GL.SDMODE2 Global SDRAM Mode Register 2 3Bh 5 0 4 0 3 0 2 LTMOD2 0 1 LTMOD1 1 0 LTMOD0 0
Bits 0 - 2: CAS Latency Mode (LTMOD0 - LTMOD2) These bits are used to setup CAS Latency Note: Only CAS Latency of 2 or 3 is allowed Note: This register has a nonzero default value. This should be taken into consideration when initializing the device. Note: After changing the value of this register, the user must toggle the GL.SDMODEWS.SDMW bit to write the new values to the SDRAM.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
GL.SDMODEWS Global SDRAM Mode Register Write Status 3Ch 5 0 4 0 3 0 2 0 1 0 0 SDMW 0
Bit 0: SDRAM Mode Write (SDMW) Setting this bit to 1 will write the current values of the mode control and refresh time control registers to the SDRAM. The user must clear this bit and set it again for subsequent write operations.
Register Name: Register Description Register Address: Bit # Name Default 7 SREFT7 0
GL.SDRFTC Global SDRAM Refresh Time Control 3Dh 6 SREFT6 1 5 SREFT5 0 4 SREFT4 0 3 SREFT3 0 2 SREFT2 1 1 SREFT1 1 0 SREFT0 0
Bits 0 - 7: SDRAM Refresh Time Control (SREFT0 - SREFT7) These 8 bits are used to control the SDRAM refresh frequency. The refresh rate will be equal to this register value x 8 x 100MHz. Note: This register has a nonzero default value. This should be taken into consideration when initializing the device. Note: After changing the value of this register, the user must toggle the GL.SDMODEWS.SDMW bit to write the new values to the SDRAM.
138 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.3 Arbiter Registers
The Arbiter manages the transport between the Ethernet port and the Serial Interface. It is responsible for queuing and dequeuing data to an external SDRAM. The arbiter handles requests from the HDLC and MAC to transfer data to/from the SDRAM. The base address of the Arbiter register space is 0040h.
11.3.1 Arbiter Register Bit Descriptions
Register Name: Register Description: Register Address: Bit # Name Default 7 RQSC7 0 6 RQSC6 0 AR.RQSC1 Arbiter Receive Queue Size Connection 40h 5 RQSC5 1 4 RQSC4 1 3 RQSC3 1 2 RQSC2 1 1 RQSC1 0 0 RQSC0 1
Bits 0-7: Receive Queue Size (RQSC[0:7]) These 7 bits of the size of receive queue associated with the connection. Receive queue is for data arriving from the MAC to be sent to the WAN. The Queue address size is defined in increments of 32 x 2048 bytes. The queue size is AR.RQSC1 multiplied by 32 to determine the number of 2048 byte packets that can be stored in the queue. This queue is constructed in the external SDRAM. Note: Queue size of 0 is not allowed and should never be set.
Register Name: Register Description: Register Address: Bit # Name Default 7 TQSC7 0 6 TQSC6 0
AR.TQSC1 Arbiter Transmit Queue Size Connection 1 41h 5 TQSC5 0 4 TQSC4 0 3 TQSC3 0 2 TQSC2 0 1 TQSC1 1 0 TQSC0 1
Bits 0-7: Transmit Queue Size (TQSC[0:7]) This is size of transmit queue associated with the connection. The queue address size is defined in increments of 32 packets. The range of bytes will depend on the external SDRAM connected to the DS33R11. Transmit queue is the data queue for data arriving on the WAN that is sent to the MAC. Note that queue size of 0 is not allowed and should never be set.
139 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.4 BERT Registers
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 PMU 0 BCR BERT Control Register 80h 5 RNPL 0 4 RPIC 0 3 MPR 0 2 APRD 0 1 TNPL 0 0 TPIC 0
Bit 7: This bit must be kept low for proper operation. Bit 6: Performance Monitoring Update (PMU) This bit causes a performance monitoring update to be initiated. A 0 to 1 transition causes the performance monitoring registers to be updated with the latest data, and the counters reset (0 or 1). For a second performance monitoring update to be initiated, this bit must be set to 0, and back to 1. If PMU goes low before the PMS bit goes high, an update might not be performed. Bit 5: Receive New Pattern Load (RNPL) A zero to one transition of this bit will cause the programmed test pattern (QRSS, PTS, PLF [4:0}, PTF [4:0], and BSP [31:0]) to be loaded in to the receive pattern generator. This bit must be changed to zero and back to one for another pattern to be loaded. Loading a new pattern will forces the receive pattern generator out of the "Sync" state which causes a resynchronization to be initiated. Note: QRSS, PTS, PLF [4:0}, PTF [4:0], and BSP [31:0] must not change from the time this bit transitions from 0 to 1 until four RCLKI clock cycles after this bit transitions from 0 to 1. Bit 4: Receive Pattern Inversion Control (RPIC) When 0, the receive incoming data stream is not altered. When 1, the receive incoming data stream is inverted. Bit 3: Manual Pattern Resynchronization (MPR) A zero to one transition of this bit will cause the receive pattern generator to resynchronize to the incoming pattern. This bit must be changed to zero and back to one for another resynchronization to be initiated. Note: A manual resynchronization forces the receive pattern generator out of the "Sync" state. Bit 2: Automatic Pattern Resynchronization Disable (APRD) When 0, the receive pattern generator will automatically resynchronize to the incoming pattern if six or more times during the current 64-bit window the incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern generator will not automatically resynchronize to the incoming pattern. Note: Automatic synchronization is prevented by not allowing the receive pattern generator to automatically exit the "Sync" state. Bit 1: Transmit New Pattern Load (TNPL) A zero to one transition of this bit will cause the programmed test pattern (QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit must be changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four TCLKE clock cycles after this bit transitions from 0 to 1. Bit 0: Transmit Pattern Inversion Control (TPIC) When 0, the transmit outgoing data stream is not altered. When 1, the transmit outgoing data stream is inverted.
140 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 QRSS 0 BPCLR BERT Pattern Configuration Low Register 82h 5 PTS 0 4 PLF4 0 3 PLF3 0 2 PLF2 0 1 PLF1 0 0 PLF0 0
Bit 6: QRSS Enable (QRSS) When 0, the pattern generator configuration is controlled by PTS, PLF[0:4], and PTF[0:4], and BSP[0:31]. When 1, the pattern generator configuration is forced to a QRSS pattern with a generating 20 17 polynomial of x + x + 1. The output of the pattern generator is forced to one if the next fourteen output bits are all zero. Bit 5: Pattern Type Select (PTS) When 0, the pattern is a PRBS pattern. When 1, the pattern is a repetitive pattern. Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 BPCHR BERT Pattern Configuration High Register 83h 5 0 4 PTF4 0 3 PTF3 0 2 PTF2 0 1 PTF1 0 0 PTF0 0
Bits 4 to 0: Pattern Tap Feedback (PTF[4:0]) These five bits control the PRBS "tap" feedback of the pattern generator. The "tap" feedback is from bit y of the pattern generator (y = PTF[4:0] +1). These bits are ignored when programmed for a repetitive pattern. For a PRBS signal, the feedback is an XOR of bit n and bit y. The values possible are outlined in Section 9.16.
141 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 BSP7 0 6 BSP6 0
BSPB0R BERT Pattern Byte0 Register 84h 5 BSP5 0 4 BSP4 0 3 BSP3 0 2 BSP2 0 1 BSP1 0 0 BSP0 0
Bits 0 to 7: BERT Pattern (BSP[7:0]) Lower eight bits of 32 bits. Register description follows next register. Register Name: Register Description: Register Address: Bit # Name Default 7 BSP15 0 6 BSP14 0 BSPB1R BERT Pattern Byte 1 Register 85h 5 BSP13 0 4 BSP12 0 3 BSP11 0 2 BSP10 0 1 BSP9 0 0 BSP8 0
Bits 0 to 7: BERT Pattern (BSP[15:8]) 8 bits of 32 bits. Register description below.
Register Name: Register Description: Register Address: Bit # Name Default 7 BSP23 0 6 BSP22 0
BSPB2R BERT Pattern Byte2 Register 86h 5 BSP21 0 4 BSP20 0 3 BSP19 0 2 BSP18 0 1 BSP17 0 0 BSP16 0
Bits 0 to 7: BERT Pattern (BSP[23:16]) 8 bits of 32 bits. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 BSP31 0 6 BSP30 0 BSPB3R BERT Seed/Pattern Byte3 Register 87h 5 BSP29 0 4 BSP28 0 3 BSP27 0 2 BSP26 0 1 BSP25 0 0 BSP24 0
Bits 0 to 8: BERT Pattern (BSP[31:24]) Upper 8 bits of 32 bits. Register description below.
BERT Pattern (BSP[31:0]) These 32 bits are the programmable seed for a transmit PRBS pattern, or the programmable pattern for a transmit or receive repetitive pattern. BSP(31) is the first bit output on the transmit side for a 32-bit repetitive pattern or 32-bit length PRBS. BSP(31) is the first bit input on the receive side for a 32-bit repetitive pattern.
142 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 TEICR Transmit Error Insertion Control Register 88h 5 TIER2 0 4 TIER1 0 3 TIER0 0 2 BEI 0 1 TSEI 0 0 0
Bits 3 - 5: Transmit Error Insertion Rate (TEIR[2:0]) These three bits indicate the rate at which errors are n inserted in the output data stream. One out of every 10 bits is inverted. TEIR[2:0] is the value n. A TEIR[2:0] value th of 0 disables error insertion at a specific rate. A TEIR[2:0] value of 1 result in every 10 bit being inverted. A th TEIR[2:0] value of 2 results in every 100 bit being inverted. Error insertion starts when this register is written to with a TEIR[2:0] value that is nonzero. If this register is written to during the middle of an error insertion process, the new error rate is started after the next error is inserted. Bit 2: Bit Error Insertion Enable (BEI) When 0, single bit error insertion is disabled. When 1, single bit error insertion is enabled. Bit 1: Transmit Single Error Insert (TSEI) This bit causes a bit error to be inserted in the transmit data stream if and single bit error insertion is enabled. A 0 to 1 transition causes a single bit error to be inserted. For a second bit error to be inserted, this bit must be set to 0, and back to 1. Note: If this bit transitions more than once between error insertion opportunities, only one error is inserted. All other bits in this register besides BEI and TSEI and TIER must be reset to 0 for proper operation.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
BSR BERT Status Register 8Ch 5 0 4 0 3 PMS 0 2 0 1 BEC 0 0 OOS 0
Bit 3: Performance Monitoring Update Status (PMS) This bit indicates the status of the receive performance monitoring register (counters) update. This bit will transition from low to high when the update is completed. PMS is asynchronously forced low when the PMU bit goes low. TCLKE and RCLKI must be present. Bit 1: Bit Error Count (BEC) When 0, the bit error count is zero. When 1, the bit error count is one or more. Bit 0: Out Of Synchronization (OOS) When 0, the receive pattern generator is synchronized to the incoming pattern. When 1, the receive pattern generator is not synchronized to the incoming pattern.
143 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 6 BSRL BERT Status Register Latched 8Eh 5 4 3 PMSL 2 BEL 1 BECL 0 OOSL -
Bit 3: Performance Monitor Update Status Latched (PMSL) This bit is set when the PMS bit transitions from 0 to 1. Bit 2: Bit Error Detected Latched (BEL) This bit is set when a bit error is detected. Bit 1: Bit Error Count Latched (BECL) This bit is set when the BEC bit transitions from 0 to 1. Bit 0: Out Of Synchronization Latched (OOSL) This bit is set when the OOS bit changes state.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
BSRIE BERT Status Register Interrupt Enable 90h 5 0 4 0 3 PMSIE 0 2 BEIE 0 1 BECIE 0 0 OOSIE 0
Bit 3: Performance Monitoring Update Status Interrupt Enable (PMSIE) This bit enables an interrupt if the PMSL bit is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Bit Error Interrupt Enable (BEIE) This bit enables an interrupt if the BEL bit is set. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Bit Error Count Interrupt Enable (BECIE) This bit enables an interrupt if the BECL bit is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Out Of Synchronization Interrupt Enable (OOSIE) This bit enables an interrupt if the OOSL bit is set. 0 = interrupt disabled 1 = interrupt enabled
144 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 BEC7 0 6 BEC6 0
RBECB0R Receive Bit Error Count Byte 0 Register 94h 5 BEC5 0 4 BEC4 0 3 BEC3 0 2 BEC2 0 1 BEC1 0 0 BEC0 0
Bits 0 - 7: Bit Error Count (BEC[0:7]) Lower eight bits of 24 bits. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 BEC15 0 6 BEC14 0 RBECB1R Receive Bit Error Count Byte 1 Register 95h 5 BEC13 0 4 BEC12 0 3 BEC11 0 2 BEC10 0 1 BEC9 0 0 BEC8 0
Bits 0 - 7: Bit Error Count (BEC[8:15]) Eight bits of a 24 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 BEC23 0 6 BEC22 0 RBECR2 Receive Bit Error Count Byte 2 Register 96h 5 BEC21 0 4 BEC20 0 3 BEC19 0 2 BEC18 0 1 BEC17 0 0 BEC16 0
Bits 0 - 7: Bit Error Count (BEC[16:23]) Upper 8-bits of the register. Bit Error Count (BEC[0:23]) These twenty-four bits indicate the number of bit errors detected in the incoming data stream. This count stops incrementing when it reaches a count of FF FFFFh. The associated bit error counter will not incremented when an OOS condition exists.
145 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 BC7 0 6 BC6 0 RBCB0 Receive Bit Count Byte 0 Register 98h 5 BC5 0 4 BC4 0 3 BC3 0 2 BC2 0 1 BC1 0 0 BC0 0
Bits 0 - 7: Bit Count (BC[0:7]) Eight bits of a 32 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 BC15 0 6 BC14 0 RBCB1 Receive Bit Count Byte 1 Register #1 99h 5 BC13 0 4 BC12 0 3 BC11 0 2 BC10 0 1 BC9 0 0 BC8 0
Bits 0 - 7: Bit Count (BC[8:15]) Eight bits of a 32 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 BC23 0 6 BC22 0 RBCB2 Receive Bit Count Byte 2 Register 9Ah 5 BC21 0 4 BC20 0 3 BC19 0 2 BC18 0 1 BC17 0 0 BC16 0
Bits 0 - 7: Bit Count (BC[16:23]) Eight bits of a 32 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 BC31 0 6 BC30 0 RBCB3 Receive Bit Count Byte 3 Register 9Bh 5 BC29 0 4 BC28 0 3 BC27 0 2 BC26 0 1 BC25 0 0 BC24 0
Bits 0 - 7: Bit Count (BC[24:31]) Upper 8-bits of the register. Bit Count (BC[0:31]) These thirty-two bits indicate the number of bits in the incoming data stream. This count stops incrementing when it reaches a count of FFFF FFFFh. The associated bit counter will not incremented when an OOS condition exists.
146 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.5 Serial Interface Registers
The Serial Interface contains the Serial HDLC transport circuitry and the associated serial port. The Serial Interface register map consists of registers that are common functions, transmit functions, and receive functions. Bits that are underlined are read-only; all other bits can be written. All reserved registers and bits with "-" designation should be written to zero, unless specifically noted in the register definition. When read, the information from reserved registers and bits designated with "-" should be discarded. Counter registers are updated by asserting (low to high transition) the associated performance monitoring update signal (xxPMU). During the counter register update process, the associated performance monitoring status signal (xxPMS) is deasserted. The counter register update process consists of loading the counter register with the current count, resetting the counter, forcing the zero count status indication low for one clock cycle, and then asserting xxPMS. No events are missed during this update procedure. A latched bit is set when the associated event occurs, and remains set until it is cleared by reading. Once cleared, a latched bit will not be set again until the associated event occurs again. Reserved configuration bits and registers should be written to zero.
11.5.1 Serial Interface Transmit and Common Registers
Serial Interface Transmit Registers are used to control the HDLC transmitter associated with each Serial Interface. The register map is shown in the following Table. Note that throughout this document the HDLC Processor is also referred to as a "packet processor".
11.5.2 Serial Interface Transmit Register Bit Descriptions
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.TSLCR Transmit Serial Interface Configuration Register 0C0h 5 0 4 0 3 0 2 0 1 0 0 TDENPLT 0
Bit 0: Transmit Data Enable Polarity (TDENPLT) If set to 1, TDEN is active low for enable. In the default mode, when TDEN is logic high, the data is enabled and output by the DS33R11.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
LI.RSTPD Serial Interface Reset Register 0C1h 5 0 4 0 3 0 2 0 1 RESET 0 0 0
Bit 1: RESET If this bit set to 1, the Data Path and Control and Status for this interface are reset. The Serial Interface is held in Reset as long as this bit is high. This bit must be high for a minimum of 200ns for a valid reset to occur.
147 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.LPBK Serial Interface Loopback Control Register 0C2h 5 0 4 0 3 0 2 0 1 0 0 QLP 0
Bit 0: Queue Loopback Enable (QLP) If this bit set to 1, data received on the Serial Interface is looped back to the Serial Interface transmitter. Received data will not be sent from the Serial Interface to the Ethernet Interface. Buffered packet data will remain in queue until the loopback is removed.
11.5.3 Transmit HDLC Processor Registers
Register Name: Register Description: Register Address: LI.TPPCL Transmit Packet Processor Control Low Register 0C4h 0 TIAEI 0
Bit # 7 6 5 4 3 2 1 Name TFAD TF16 TIFV TSD TBRE Default 0 0 0 0 0 0 0 Note: The user should take care not to modify this register value during packet error insertion.
Bits 5 - 6: Transmit FCS Append Disable (TFAD) - This bit controls whether or not an FCS is appended to the end of each packet. When equal to 0, the calculated FCS bytes are appended to packets. When set to 1, packets are transmitted without FCS. In X.86 Mode, FCS is always 32 bits and is always appended to the packet. Bit 4: Transmit FCS-16 Enable (TF16) - When 0, the FCS processing uses a 32-bit FCS. When 1, the FCS processing uses a 16-bit FCS. In X.86 Mode, 32-bit FCS processing is always enabled, regardless of this bit. Bit 3: Transmit Bit Synchronous Inter-frame Fill Value (TIFV) - When 0, inter-frame fill is done with the flag sequence (7Eh). When 1, inter-frame fill is done with all '1's (FFh). This bit is ignored in X.86 mode and the interframe flag is always 7E. Bit 2: Transmit Scrambling Disable (TSD) - When equal to 0, X +1 scrambling is performed. When set to 1, scrambling is disabled. Bit 1: Transmit Bit Reordering Enable (TBRE) - When equal to 0, bit reordering is disabled (The first bit transmitted is from the MSB of the transmit FIFO byte TFD [7]). When set to 1, bit reordering is enabled (The first bit transmitted is from the LSB of the transmit FIFO byte TFD [0]). Bit 0: Transmit Initiate Automatic Error Insertion (TIAEI) - This write-only bit initiates error insertion. See the LI.TEPHC register definition for details of usage.
43
148 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TIFG7 0 6 TIFG6 0 LI.TIFGC Transmit Inter-Frame Gapping Control Register 0C5h 5 TIFG5 0 4 TIFG4 0 3 TIFG3 0 2 TIFG2 0 1 TIFG1 0 0 TIFG0 1
Bits 0 - 7: Transmit Inter-Frame Gapping (TIFG[7:0]) - These eight bits indicate the number of additional flags and bytes of inter-frame fill to be inserted between packets. The number of flags and bytes of inter-frame fill between packets is at least the value of TIFG[7:0] plus 1. Note: If inter-frame fill is set to all 1's, a TFIG value of 2 or 3 will result in a flag, two bytes of 1's, and an additional flag between packets. Register Name: Register Description: Register Address: Bit # Name Default 7 TPEN7 0 6 TPEN6 0 LI.TEPLC Transmit Errored Packet Low Control Register 0C6h 5 TPEN5 0 4 TPEN4 0 3 TPEN3 0 2 TPEN2 0 1 TPEN1 0 0 TPEN0 0
Bits 0 - 7: Transmit Errored Packet Insertion Number (TPEN[7:0]) - These eight bits indicate the total number of errored packets to be transmitted when triggered by TIAEI. Error insertion will end after this number of errored packets have been transmitted. A value of FFh results in continuous errored packet insertion at the specified rate.
149 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 MEIMS 0 6 TPER6 0 LI.TEPHC Transmit Errored Packet High Control Register 0C7h 5 TPER5 0 4 TPER4 0 3 TPER3 0 2 TPER2 0 1 TPER1 0 0 TPER0 0
Bit 7: Manual Error Insert Mode Select (MEIMS) - When 0, the transmit manual error insertion signal (TMEI) will not cause errors to be inserted. When 1, TMEI will cause an error to be inserted when it transitions from a 0 to a 1. Note: Enabling TMEI does not disable error insertion using TCER[6:0] and TCEN[7:0]. Bits 0 - 6: Transmit Errored Packet Insertion Rate (TPER[6:0]) - These seven bits indicate the rate at which y errored packets are to be output. One out of every x * 10 packets is to be an errored packet. TPER[3:0] is the value x, and TPER[6:4] is the value y which has a maximum value of 6. If TPER[3:0] has a value of 0h errored packet 6 insertion is disabled. If TPER[6:4] has a value of 6xh or 7xh the errored packet rate is x * 10 . A TPER[6:0] value of th 01h results in every packet being errored. A TPER[6:0] value of 0Fh results in every 15 packet being errored. A th TPER[6:0] value of 11h results in every 10 packet being errored. To initiate automatic error insertion, use the following routine: 1) Configure LI.TEPLC and LI.TEPHC for the desired error insertion mode. 2) Write the LI.TPPCL.TIAEI bit to 1. Note that this bit is write-only. 3) If not using continuous error insertion (LI.TPELC is not equal to FFh), the user should monitor the LI.TPPSR.TEPF bit for completion of the error insertion. If interrupt on completion of error insertion is enabled (LI.TPPSRIE.TEPFIE = 1), the user only needs to wait for the interrupt condition. 4) Proceed with the cleanup routine listed below. Cleanup routine: 1) Write LI.TEPLC and LI.TEPHC each to 00h. 2) Write the LI.TPPCL.TIAEI bit to 0.
150 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.TPPSR Transmit Packet Processor Status Register 0C8h 5 0 4 0 3 0 2 0 1 0 0 TEPF 0
Bit 0: Transmit Errored Packet Insertion Finished (TEPF) - This bit is set when the number of errored packets indicated by the TPEN[7:0] bits in the TEPC register have been transmitted. This bit is cleared when errored packet insertion is disabled, or a new errored packet insertion process is initiated.
Register Name: Register Description: Register Address: Bit # Name Default 7 6 -
LI.TPPSRL Transmit Packet Processor Status Register Latched 0C9h 5 4 3 2 1 0 TEPFL -
Bit 0: Transmit Errored Packet Insertion Finished Latched (TEPFL) - This bit is set when the TEPF bit in the TPPSR register transitions from zero to one.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
LI.TPPSRIE Transmit Packet Processor Status Register Interrupt Enable 0CAh 5 0 4 0 3 0 2 0 1 0 0 TEPFIE 0
Bit 0: Transmit Errored Packet Insertion Finished Interrupt Enable (TEPFIE) - This bit enables an interrupt if the TEPFL bit in the LI.TPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled
151 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TPC7 0 6 TPC6 0 LI.TPCR0 Transmit Packet Count Byte 0 0CCh 5 TPC5 0 4 TPC4 0 3 TPC3 0 2 TPC2 0 1 TPC1 0 0 TPC0 0
Bits 0 - 7: Transmit Packet Count (TPC[7:0]) - Eight bits of 24 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 TPC15 0 6 TPC14 0 LI.TPCR1 Transmit Packet Count Byte 1 0CDh 5 TPC13 0 4 TPC12 0 3 TPC11 0 2 TPC10 0 1 TPC9 0 0 TPC8 0
Bits 0 - 7: Transmit Packet Count (TPC[15:8]) - Eight bits of 24 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 TPC23 0 6 TPC22 0 LI.TPCR2 Transmit Packet Count Byte 2 0CEh 5 TPC21 0 4 TPC20 0 3 TPC19 0 2 TPC18 0 1 TPC17 0 0 TPC16 0
Bits 0 - 7: Transmit Packet Count (TPC[23:16]) - These twenty-four bits indicate the number of packets extracted from the Transmit FIFO and output in the outgoing data stream.
152 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 TBC7 0 6 TBC6 0
LI.TBCR0 Transmit Byte Count Byte 0 0D0h 5 TBC5 0 4 TBC4 0 3 TBC3 0 2 TBC2 0 1 TBC1 0 0 TBC0 0
Bits 0 - 7: Transmit Byte Count (TBC[0:7]) - Eight bits of 32 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 TBC15 0 6 TBC14 0 LI.TBCR1 Transmit Byte Count Byte 1 0D1h 5 TBC13 0 4 TBC12 0 3 TBC11 0 2 TBC10 0 1 TBC9 0 0 TBC8 0
Bits 0 - 7: Transmit Byte Count (TBC[15:8]) - Eight bits of 32 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 TBC23 0 6 TBC22 0 LI.TBCR2 Transmit Byte Count Byte 2 0D2h 5 TBC21 0 4 TBC20 0 3 TBC19 0 2 TBC18 0 1 TBC17 0 0 TBC16 0
Bits 0 - 7: Transmit Byte Count (TBC[23:16]) - Eight bits of 32 bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 TBC31 0 6 TBC30 0 LI.TBCR3 Transmit Byte Count Byte 3 0D3h 5 TBC29 0 4 TBC28 0 3 TBC27 0 2 TBC26 0 1 TBC25 0 0 TBC24 0
Bits 0 - 7: Transmit Byte Count (TBC[31:24]) - These thirty-two bits indicate the number of packet bytes inserted in the outgoing data stream.
153 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.TMEI Transmit Manual Error Insertion 0D4h 5 0 4 0 3 0 2 0 1 0 0 TMEI 0
Bit 0: Transmit Manual Error Insertion (TMEI) A zero to one transition will insert a single error in the Transmit direction.
Register Name: Register Description: Register Address: Bit # Name Default 7 0
LI.THPMUU Serial Interface Transmit HDLC PMU Update Register 0D6h 6 0 5 0 4 0 3 0 2 0 1 0 0 TPMUU 0
Bit 0: Transmit PMU Update (TPMUU) This signal causes the transmit cell/packet processor block performance monitoring registers (counters) to be updated. A 0 to 1 transition causes the performance monitoring registers to be updated with the latest data, and the counters reset (0 or 1). This update updates performance monitoring counters for the Serial Interface.
Register Name: Register Description: Register Address: Bit # Name Default 7 0
LI.THPMUS Serial Interface Transmit HDLC PMU Update Status Register 0D7h 6 0 5 0 4 0 3 0 2 0 1 0 0 TPMUS 0
Bit 0: Transmit PMU Update Status (TPMUS) This bit is set when the Transmit PMU Update is completed. This bit is cleared when TPMUU is reset.
154 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.5.4 X.86 Registers
X.86 Transmit and common Registers are used to control the operation of the X.86 encoder and decoder. Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.TX86EDE X.86 Encoding Decoding Enable 0D8h 5 0 4 0 3 0 2 0 1 0 0 X86ED 0
Bit 0: X.86 Encoding Decoding (X86ED) If this bit is set to 1, X.86 encoding and decoding is enabled for the Transmit and Receive paths. The MAC Frame is encapsulated in the X.86 Frame for Transmit and the X.86 headers are checked for in the received data. If X.86 functionality is selected, the X.86 receiver byte boundary is provided by the RBSYNC signal and the DS33R11 provides the transmit byte synchronization TBSYNC. No HDLC encapsulation is performed. Register Name: Register Description: Register Address: Bit # Name Default 7 X86TRA7 0 LI.TRX86A Transmit Receive X.86 Address 0D9h 6 X86TRA6 0 5 X86TRA5 0 4 X86TRA4 0 3 X86TRA3 0 2 X86TRA2 1 1 X86TRA1 0 0 X86TRA0 0
Bits 0 - 7: X86 Transmit Receive Address (X86TRA0-7) This is the address field for the X.86 transmitter and for the receiver. The register default value is 0x04.
Register Name: Register Description: Register Address: Bit # Name Default 7 X86TRC7 0
LI.TRX8C Transmit Receive X.86 Control 0DAh 6 X86TRC6 0 5 X86TRC5 0 4 X86TRC4 0 3 X86TRC3 0 2 X86TRC2 0 1 X86TRC1 1 0 X86TRC0 1
Bits 0 - 7: X86 Transmit Receive Control (X86TRC0-7) This is the control field for the X.86 transmitter and expected value for the receiver. The register is reset to 0x03 Register Name: Register Description: Register Address: Bit # Name Default 7
TRSAPIH7
LI.TRX86SAPIH Transmit Receive X.86 SAPIH 0DBh 6
TRSAPIH6
5
TRSAPIH5
4
TRSAPIH4
3
TRSAPIH3
2
TRSAPIH2
1
TRSAPIH1
0
TRSAPIH0
1
1
1
1
1
1
1
0
Bits 0 - 7: X86 Transmit Receive Address (TRSAPIH0-7) This is the address field for the X.86 transmitter and expected for the receiver. The register is reset to 0xfe.
155 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7
TRSAPIL7
LI.TRX86SAPIL Transmit Receive X.86 SAPIL 0DCh 6
TRSAPIL6
5
TRSAPIL5
4
TRSAPIL4
3
TRSAPIL3
2
TRSAPIL2
1
TRSAPIL1
0
TRSAPIL0
0
0
0
0
0
0
0
1
Bits 0 - 7: X86 Transmit Receive Control (TRSAPIL0-7) This is the address field for the X.86 transmitter and expected value for the receiver. The register is reset to 0x01
Register Name: Register Description: Register Address: Bit # Name Default 7 CIRE 0 6 CIR6 0
LI.CIR Committed Information Rate 0DDh 5 CIR5 0 4 CIR4 0 3 CIR3 0 2 CIR2 0 1 CIR1 0 0 CIR0 1
Bit 7: Committed Information Rate Enable (CIRE) Set this bit to 1 to enable the Committed Information Rate Controller feature. Bits 0 - 6: Committed Information Rate (CIR0-6) These bits provide the value for the committed information rate. The value is multiplied by 500kbit/s to get the CIR value. The user must ensure that the CIR value is less than or equal to the maximum Serial Interface transmit rate. The valid range is from 1 to 104. Any values outside this range will result in unpredictable behavior. Note that a value of 104 translates to a 52Mbit/s line rate. Hence if the CIR is above the line rate, the rate is not restricted by the CIR. For instance - if using a T1 line and the CIR is programmed with a value of 104, it has no effect in restricting the rate.
156 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.5.5 Receive Serial Interface
Serial Receive Registers are used to control the HDLC Receiver associated with each Serial Interface. Note that throughout this document HDLC Processor is also referred to as "Packet Processor". The receive packet processor block has seventeen registers.
11.5.5.1 Register Bit Descriptions Register Name: LI.RSLCR Register Description: Receive Serial Interface Configuration Register Register Address: 100h Bit # Name Default 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 RDENPLT 0
Bit 0: Receive Data Enable Polarity (RDENPLT) Receive Data Enable Polarity. If set to 1, RDEN Low enables reception of the bit.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
LI.RPPCL Receive Packet Processor Control Low Register 101h 5 RFPD 0 4 RF16 0 3 RFED 0 2 RDD 0 1 RBRE 0 0 RCCE 0
Bit 5: Receive FCS Processing Disable (RFPD) - When equal to 0, FCS processing is performed and FCS is appended to packets. When set to 1, FCS processing is disabled (the packets do not have an FCS appended). In X.86 mode, FCS processing is always enabled. Bit 4: Receive FCS-16 Enable (RF16) - When 0, the error checking circuit uses a 32-bit FCS. When 1, the error checking circuit uses a 16-bit FCS. This bit is ignored when FCS processing is disabled. In X.86 mode, the FCS is always 32 bits. Bit 3: Receive FCS Extraction Disable (RFED) - When 0, the FCS bytes are discarded. When 1, the FCS bytes are passed on. This bit is ignored when FCS processing is disabled. In X.86 mode, FCS bytes are discarded. Bit 2: Receive Descrambling Disable (RDD) - When equal to 0, X +1 descrambling is performed. When set to 1, descrambling is disabled. Bit 1: Receive Bit Reordering Enable (RBRE) - When equal to 0, reordering is disabled and the first bit received is expected to be the MSB DT [7] of the byte. When set to 1, bit reordering is enabled and the first bit received is expected to be the LSB DT [0] of the byte. Bit 0: Receive Clear Channel Enable (RCCE) - When equal to 0, packet processing is enabled. When set to 1, the device is in clear channel mode and all packet-processing functions except descrambling and bit reordering are disabled.
43
157 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RMX7 1 6 RMX6 1
LI.RMPSCL Receive Maximum Packet Size Control Low Register 102h 5 RMX5 1 4 RMX4 0 3 RMX3 0 2 RMX2 0 1 RMX1 0 0 RMX0 0
Bits 0 - 7: Receive Maximum Packet Size (RMX[7:0]) Eight bits of a sixteen bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RMX15 0 6 RMX14 0 LI.RMPSCH Receive Maximum Packet Size Control High Register 103h 5 RMX13 0 4 RMX12 0 3 RMX11 0 2 RMX10 1 1 RMX9 1 0 RMX8 1
Bits 0-7: Receive Maximum Packet Size (RMX[8:15]) These sixteen bits indicate the maximum allowable packet size in bytes. The size includes the FCS bytes, but excludes bit/byte stuffing. Note: If the maximum packet size is less than the minimum packet size, all packets are discarded. When packet processing is disabled, these sixteen bits indicate the "packet" size the incoming data is to be broken into. The maximum packet size allowable is 2016 bytes plus the FCS bytes. Any values programmed that are greater than 2016 + FCS will have the same effect as 2016+ FCS value. In X.86 mode, the X.86 encapsulation bytes are included in maximum size control.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
LI.RPPSR Receive Packet Processor Status Register 104h 5 0 4 0 3 0 2 REPC 0 1 RAPC 0 0 RSPC 0
Bit 2: Receive FCS Errored Packet Count (REPC) This read only bit indicates that the receive FCS errored packet count is nonzero. Bit 1: Receive Aborted Packet Count (RAPC) This read only bit indicates that the receive aborted packet count is nonzero. Bit 0: Receive Size Violation Packet Count (RSPC) This read only bit indicates that the receive size violation packet count is nonzero.
158 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 REPL 6 RAPL LI.RPPSRL Receive Packet Processor Status Register Latched 105h 5 RIPDL 4 RSPDL 3 RLPDL 2 REPCL 1 RAPCL 0 RSPCL -
Bit 7: Receive FCS Errored Packet Latched (REPL) This bit is set when a packet with an errored FCS is detected. Bit 6: Receive Aborted Packet Latched (RAPL) This bit is set when a packet with an abort indication is detected. Bit 5: Receive Invalid Packet Detected Latched (RIPDL) This bit is set when a packet with a noninteger number of bytes is detected. Bit 4: Receive Small Packet Detected Latched (RSPDL) This bit is set when a packet smaller than the minimum packet size is detected. Bit 3: Receive Large Packet Detected Latched (RLPDL) This bit is set when a packet larger than the maximum packet size is detected. Bit 2: Receive FCS Errored Packet Count Latched (REPCL) This bit is set when the REPC bit in the RPPSR register transitions from zero to one. Bit 1: Receive Aborted Packet Count Latched (RAPCL) This bit is set when the RAPC bit in the RPPSR register transitions from zero to one. Bit 0: Receive Size Violation Packet Count Latched (RSPCL) This bit is set when the RSPC bit in the RPPSR register transitions from zero to one.
159 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 REPIE 0 6 RAPIE 0 LI.RPPSRIE Receive Packet Processor Status Register Interrupt Enable 106h 5 RIPDIE 0 4 RSPDIE 0 3 RLPDIE 0 2 REPCIE 0 1 RAPCIE 0 0 RSPCIE 0
Bit 7: Receive FCS Errored Packet Interrupt Enable (REPIE) This bit enables an interrupt if the REPL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled Bit 6: Receive Aborted Packet Interrupt Enable (RAPIE) This bit enables an interrupt if the RAPL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled Bit 5: Receive Invalid Packet Detected Interrupt Enable (RIPDIE) This bit enables an interrupt if the RIPDL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled Bit 4: Receive Small Packet Detected Interrupt Enable (RSPDIE) This bit enables an interrupt if the RSPDL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled Bit 3: Receive Large Packet Detected Interrupt Enable (RLPDIE) This bit enables an interrupt if the RLPDL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled Bit 2: Receive FCS Errored Packet Count Interrupt Enable (REPCIE) This bit enables an interrupt if the REPCL bit in the LI.RPPSRL register is set. Must be set low when the packets do not have an FCS appended. 0 = interrupt disabled 1 = interrupt enabled Bit 1: Receive Aborted Packet Count Interrupt Enable (RAPCIE) This bit enables an interrupt if the RAPCL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled Bit 0: Receive Size Violation Packet Count Interrupt Enable (RSPCIE) This bit enables an interrupt if the RSPCL bit in the LI.RPPSRL register is set. 0 = interrupt disabled 1 = interrupt enabled
160 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RPC7 0 6 RPC6 0 LI.RPCB0 Receive Packet Count Byte 0 Register 108h 5 RPC5 0 4 RPC4 0 3 RPC3 0 2 RPC2 0 1 RPC1 0 0 RPC0 0
Bits 0 - 7: Receive Packet Count (RPC [7:0]) Eight bits of a 24-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RPC15 0 6 RPC14 0 LI.RPCB1 Receive Packet Count Byte 1 Register 109h 5 RPC13 0 4 RPC12 0 3 RPC11 0 2 RPC10 0 1 RPC09 0 0 RPC08 0
Bits 0 - 7: Receive Packet Count (RPC [15:8]) Eight bits of a 24-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RPC23 0 6 RPC22 0 LI.RPCB2 Receive Packet Count Byte 2 Register 10Ah 5 RPC21 0 4 RPC20 0 3 RPC19 0 2 RPC18 0 1 RPC17 0 0 RPC16 0
Bits 0 - 7: Receive Packet Count (RPC [23:16]) These twenty-four bits indicate the number of packets stored in the receive FIFO without an abort indication. Note: Packets discarded due to system loopback or an overflow condition are included in this count. This register is valid when clear channel is enabled.
161 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RFPC7 0 6 RFPC6 0
LI.RFPCB0 Receive FCS Errored Packet Count Byte 0 Register 10Ch 5 RFPC5 0 4 RFPC4 0 3 RFPC3 0 2 RFPC2 0 1 RFPC1 0 0 RFPC0 0
Bits 0 - 7: Receive FCS Errored Packet Count (RFPC[7:0]) Eight bits of a 24-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RFPC15 0 LI.RFPCB1 Receive FCS Errored Packet Count Byte 1 Register 10Dh 6 RFPC14 0 5 RFPC13 0 4 RFPC12 0 3 RFPC11 0 2 RFPC10 0 1 RFPC9 0 0 RFPC8 0
Bits 0 - 7: Receive FCS Errored Packet Count (RFPC[15:8]) Eight bits of a 24-bit value. Register description below.
Register Name: Register Description: Register Address: Bit # Name Default 7 RFPC23 0
LI.RFPCB2 Receive FCS Errored Packet Count Byte 2 Register 10Eh 6 RFPC22 0 5 RFPC21 0 4 RFPC20 0 3 RFPC19 0 2 RFPC18 0 1 RFPC17 0 0 RFPC16 0
Receive FCS Errored Packet Count (RFPC[23:16]) These twenty-four bits indicate the number of packets received with an FCS error. The byte count for these packets is included in the receive aborted byte count register REBCR.
162 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RAPC7 0 6 RAPC6 0
LI.RAPCB0 Receive Aborted Packet Count Byte 0 Register 110h 5 RAPC5 0 4 RAPC4 0 3 RAPC3 0 2 RAPC2 0 1 RAPC1 0 0 RAPC0 0
Bits 0 - 7: Receive Aborted Packet Count (RAPC [7:0]) Eight bits of a 24-bit value. Register description below.
Register Name: Register Description: Register Address: Bit # Name Default 7 RAPC15 0
LI.RAPCB1 Receive Aborted Packet Count Byte 1 Register 111h 6 RAPC14 0 5 RAPC13 0 4 RAPC12 0 3 RAPC11 0 2 RAPC10 0 1 RAPC9 0 0 RAPC8 0
Bits 0 - 7: Receive Aborted Packet Count (RAPC[15:8]) Eight bits of a 24-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RAPC23 0 LI.RAPCB2 Receive Aborted Packet Count Byte 2 Register 112h 6 RAPC22 0 5 RAPC21 0 4 RAPC20 0 3 RAPC19 0 2 RAPC18 0 1 RAPC17 0 0 RAPC16 0
Bits 0 - 7: Receive Aborted Packet Count (RAPC [23:16]) The twenty-four bit value from these three registers indicates the number of packets received with a packet abort indication. The byte count for these packets is included in the receive aborted byte count register REBCR.
163 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RSPC7 0 6 RSPC6 0
LI.RSPCB0 Receive Size Violation Packet Count Byte 0 Register 114h 5 RSPC5 0 4 RSPC4 0 3 RSPC3 0 2 RSPC2 0 1 RSPC1 0 0 RSPC0 0
Bits 0 - 7: Receive Size Violation Packet Count (RSPC [7:0]) Eight bits of a 24-bit value. Register description below.
Register Name: Register Description: Register Address: Bit # Name Default 7 RSPC15 0
LI.RSPCB1 Receive Size Violation Packet Count Byte 1 Register 115h 6 RSPC14 0 5 RSPC13 0 4 RSPC12 0 3 RSPC11 0 2 RSPC10 0 1 RSPC9 0 0 RSPC8 0
Bits 0 - 7: Receive Size Violation Packet Count (RSPC [15:8]) Eight bits of a 24-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RSPC23 0 LI.RSPCB2 Receive Size Violation Packet Count Byte 2 Registers 116h 6 RSPC22 0 5 RSPC21 0 4 RSPC20 0 3 RSPC19 0 2 RSPC18 0 1 RSPC17 0 0 RSPC16 0
Bits 0 - 7: Receive Size Violation Packet Count (RSPC [23:16]) These twenty-four bits indicate the number of packets received with a packet size violation (below minimum, above maximum, or noninteger number of bytes). The byte count for these packets is included in the receive aborted byte count register REBCR.
164 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RBC7 0 6 RBC6 0
LI.RBC0 Receive Byte Count 0 Register 118h 5 RBC5 0 4 RBC4 0 3 RBC3 0 2 RBC2 0 1 RBC1 0 0 RBC0 0
Bits 0 - 7: Receive Byte Count (RBC [7:0]) Eight bits of a 32-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RBC15 0 6 RBC14 0 LI.RBC1 Receive Byte Count 1 Register 119h 5 RBC13 0 4 RBC12 0 3 RBC11 0 2 RBC10 0 1 RBC9 0 0 RBC8 0
Bits 0 - 7: Receive Byte Count (RBC [15:8]) Eight bits of a 32-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RBC23 0 6 RBC22 0 LI.RBC2 Receive Byte Count 2 Register 11Ah 5 RBC21 0 4 RBC20 0 3 RBC19 0 2 RBC18 0 1 RBC17 0 0 RBC16 0
Bits 0 - 7: Receive Byte Count (RBC [23:16]) Eight bits of a 32-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 RBC31 0 6 RBC30 0 LI.RBC3 Receive Byte Count 3 Register 11Bh 5 RBC29 0 4 RBC28 0 3 RBC27 0 2 RBC26 0 1 RBC25 0 0 RBC24 0
Bits 0 - 7: Receive Byte Count (RBC [31:24]) These thirty-two bits indicate the number of bytes contained in packets stored in the receive FIFO without an abort indication. Note: Bytes discarded due to FCS extraction, system loopback, FIFO reset, or an overflow condition may be included in this count.
165 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 REBC7 0 6 REBC6 0
LI.RAC0 Receive Aborted Byte Count 0 Register 11Ch 5 REBC5 0 4 REBC4 0 3 REBC3 0 2 REBC2 0 1 REBC1 0 0 REBC0 0
Bits 0 - 7: Receive Aborted Byte Count (RBC [7:0]) Eight bits of a 32-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 REBC15 0 LI.RAC1 Receive Aborted Byte Count 1 Register 11Dh 6 REBC14 0 5 REBC13 0 4 REBC12 0 3 REBC11 0 2 REBC10 0 1 REBC9 0 0 REBC8 0
Bits 0 - 7: Receive Aborted Byte Count (RBC [15:8]) Eight bits of a 32-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 REBC23 0 LI.RAC2 Receive Aborted Byte Count 2 Register 11Eh 6 REBC22 0 5 REBC21 0 4 REBC20 0 3 REBC19 0 2 REBC18 0 1 REBC17 0 0 REBC16 0
Bits 0 - 7: Receive Aborted Byte Count (RBC [16:23]) Eight bits of a 32-bit value. Register description below. Register Name: Register Description: Register Address: Bit # Name Default 7 REBC31 0 LI.RAC3 Receive Aborted Byte Count 3 Register 11Fh 6 REBC30 0 5 REBC29 0 4 REBC28 0 3 REBC27 0 2 REBC26 0 1 REBC25 0 0 REBC24 0
Bits 0 - 7: Receive Aborted Byte Count (REBC[31:24]) These thirty-two bits indicate the number of bytes contained in packets stored in the receive FIFO with an abort indication. Note: Bytes discarded due to FCS extraction, system loopback, FIFO reset, or an overflow condition may be included in this count.
166 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 LI.RHPMUU Serial Interface Receive HDLC PMU Update Register 120h 6 0 5 0 4 0 3 0 2 0 1 0 0 RPMUU 0
Bit 0: Receive PMU Update (RPMUU) This signal causes the receive cell/packet processor block performance monitoring registers (counters) to be updated. A 0 to 1 transition causes the performance monitoring registers to be updated with the latest data, and the counters reset (0 or 1). This update updates performance monitoring counters for the Serial Interface. Register Name: Register Description: Register Address: Bit # Name Default 7 0 LI.RHPMUS Serial Interface Receive HDLC PMU Update Status Register 121h 6 0 5 0 4 0 3 0 2 0 1 0 0 RPMUUS 0
Bit 0: Receive PMU Update Status (RPMUUS) This bit is set when the Transmit PMU Update is completed. This bit is cleared when RPMUU is set to 0. Register Name: Register Description: Register Address: Bit # Name Default 7 6 LI.RX86S Receive X.86 Latched Status Register 122h 5 4 3 SAPIHNE 2 SAPILNE 1 CNE 0 ANE -
Bit 3: SAPI High is not equal to LI.TRX86SAPIH Latched Status (SAPIHNE) This latched status bit is set if SAPIH is not equal to LI.TRX86SAPIH. This latched status bit is cleared upon read. Bit 2: SAPI Low is not equal to LI.TRX86SAPIL Latched Status (SAPILNE) This latched status bit is set if SAPIL is not equal to LI.TRX86SAPIL. This latched status bit is cleared upon read. Bit 1: Control is not equal to LI.TRX8C (CNE) This latched status bit is set if the control field is not equal to LI.TRX8C. This latched status bit is cleared upon read. Bit 0: Address is not equal to LI.TRX86A (ANE) This latched status bit is set if the X.86 Address field is not equal to LI.TRX86A. This latched status bit is cleared upon read.
167 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.RX86LSIE Receive X.86 Interrupt Enable 123h 5 0 4 0 3 SAPINE01IM 0 2 SAPINEFEIM 0 1 CNE3LIM 0 0 ANE4IM 0
Bit 3: SAPI Octet not equal to LI.TRX86SAPIH Interrupt Enable (SAPINE01IM) If this bit is set to 1, LI.RX86S.SAPIHNE will generate an interrupt. Bit 2: SAPI Octet not equal to LI.TRX86SAPIL Interrupt Enable (SAPINEFEIM) If this bit is set to 1, LI.RX86S.SAPILNE will generate an interrupt. Bit 1: Control not equal to LI.TRX8C Interrupt Enable (CNE3LIM) If this bit is set to 1, LI.RX86S.CNE will generate an interrupt. Bit 0: Address not equal to LI.TRX86A Interrupt Enable (ANE4IM) If this bit is set to 1, LI.RX86S.ANE will generate an interrupt. Register Name: Register Description: Register Address: Bit # Name Default 7 TQLT7 0 6 TQLT6 0 LI.TQLT Serial Interface Transmit Queue Low Threshold (Watermark) 124h 5 TQLT5 0 4 TQLT4 0 3 TQLT3 0 2 TQLT2 0 1 TQLT1 0 0 TQLT0 0
Bits 0 - 7: Transmit Queue Low Threshold (TQLT[0:7]) The transmit queue low threshold for the connection, in increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to determine the byte location of the threshold. Note that the transmit queue is for data that was received from the Serial Interface to be sent to the Ethernet Interface.
Register Name: Register Description: Register Address: Bit # Name Default 7 TQHT7 0 6 TQHT6 0
LI.TQHT Serial Interface Transmit Queue High Threshold (Watermark) 125h 5 TQHT5 0 4 TQHT4 0 3 TQHT3 0 2 TQHT2 0 1 TQHT1 0 0 TQHT0 0
Bits 0 - 7: Transmit Queue High Threshold (TQHT[0:7]) The transmit queue high threshold for the connection, in increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to determine the byte location of the threshold. Note that the transmit queue is for data that was received from the Serial Interface to be sent to the Ethernet Interface.
168 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 LI.TQTIE Serial Interface Transmit Queue Cross Threshold Interrupt Enable 126h 5 0 4 0 3 TFOVFIE 0 2 TQOVFIE 0 1 TQHTIE 0 0 TQLTIE 0
Bit 3: Transmit FIFO Overflow for Connection Interrupt Enable (TFOVFIE) If this bit is set, the watermark interrupt is enabled for TFOVFLS. Bit 2: Transmit Queue Overflow for Connection Interrupt Enable (TQOVFIE) If this bit is set, the watermark interrupt is enabled for TQOVFLS. Bit 1: Transmit Queue for Connection High Threshold Interrupt Enable (TQHTIE) If this bit is set, the watermark interrupt is enabled for TQHTS. Bit 0: Transmit Queue for Connection Low Threshold Interrupt Enable (TQLTIE) If this bit is set, the watermark interrupt is enabled for TQLTS. Register Name: Register Description: Register Address: Bit # Name Default 7 6 LI.TQCTLS Serial Interface Transmit Queue Cross Threshold Latched Status 127h 5 4 3 TFOVFLS 2 TQOVFLS 1 TQHTLS 0 TQLTLS -
Bit 3: Transmit Queue FIFO Overflowed Latched Status (TFOVFLS) This bit is set if the transmit queue FIFO has overflowed. This register is cleared after a read. This FIFO is for data to be transmitted from the HDLC to be sent to the SDRAM. Bit 2: Transmit Queue Overflow Latched Status (TQOVFLS) This bit is set if the transmit queue has overflowed. This register is cleared after a read. Bit 1: Transmit Queue for Connection Exceeded High Threshold Latched Status (TQHTLS) This bit is set if the transmit queue crosses the High Watermark. This register is cleared after a read. Bit 0: Transmit Queue for Connection Exceeded Low Threshold Latched Status (TQLTLS) This bit is set if the transmit queue crosses the Low Watermark. This register is cleared after a read.
169 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.6 Ethernet Interface Registers
The Ethernet Interface registers are used to configure RMII/MII bus operation and establish the MAC parameters as required by the user. The MAC Registers cannot be addressed directly from the Processor port. The registers below are used to perform indirect read or write operations to the MAC registers. The MAC Status Registers are shown in Table 11-7. Accessing the MAC Registers is described in the Section 9.15.
11.6.1 Ethernet Interface Register Bit Descriptions
Register Name: Register Description: Register Address: Bit # Name 7 MACRA7 0 SU.MACRADL MAC Read Address Low Register 140h 6 MACRA6 0 5 MACRA5 0 4 MACRA4 0 3 MACRA3 0 2 MACRA2 0 1 MACRA1 0 0 MACRA0 0
Bits 0 - 7: MAC Read Address (MACRA0-7) Low byte of the MAC indirect register address. Used only for read operations. Register Name: Register Description: Register Address: Bit # Name 7 MACRA15 0 SU.MACRADH MAC Read Address High Register 141h 6 MACRA14 0 5 MACRA13 0 4 MACRA12 0 3 MACRA11 0 2 MACRA10 0 1 MACRA9 0 0 MACRA8 0
Bits 0 - 7: MAC Read Address (MACRA8-15) High byte of the MAC indirect register address. Used only for read operations.
Register Name: Register Description: Register Address: Bit # Name 7 MACRD7 0
SU.MACRD0 MAC Read Data Byte 0 142h 6 MACRD6 0 5 MACRD5 0 4 MACRD4 0 3 MACRD3 0 2 MACRD2 0 1 MACRD1 0 0 MACRD0 0
Bits 0 - 7: MAC Read Data 0 (MACRD0-7) One of four bytes of data read from the MAC. Valid after a read command has been issued and the SU.MACRWC.MCS bit is zero.
170 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name 7 MACRD15 0
SU.MACRD1 MAC Read Data Byte 1 143h 6 MACRD14 0 5 MACRD13 0 4 MACRD12 0 3 MACRD11 0 2 MACRD10 0 1 MACRD9 0 0 MACRD8 0
Bits 0 - 7: MAC Read Data 1 (MACRD8-15) One of four bytes of data read from the MAC. Valid after a read command has been issued and the SU.MACRWC.MCS bit is zero.
Register Name: Register Description: Register Address: Bit # Name 7 MACRD23 0
SU.MACRD2 MAC Read Data Byte 2 144h 6 MACRD22 0 5 MACRD21 0 4 MACRD20 0 3 MACRD19 0 2 MACRD18 0 1 MACRD17 0 0 MACRD16 0
Bits 0 - 7: MAC Read Data 2 (MACRD16-23) One of four bytes of data read from the MAC. Valid after a read command has been issued and the SU.MACRWC.MCS bit is zero. Register Name: Register Description: Register Address: Bit # Name 7 MACRD31 0 SU.MACRD3 MAC Read Data byte 3 145h 6 MACRD30 0 5 MACRD29 0 4 MACRD28 0 3 MACRD27 0 2 MACRD26 0 1 MACRD25 0 0 MACRD24 0
Bits 0 - 7: MAC Read Data 3 (MACRD24-31) One of four bytes of data read from the MAC. Valid after a read command has been issued and the SU.MACRWC.MCS bit is zero. Register Name: Register Description: Register Address: Bit # Name 7 MACWD7 0 SU.MACWD0 MAC Write Data 0 146h 6 MACWD6 0 5 MACWD5 0 4 MACWD4 0 3 MACWD3 0 2 MACWD2 0 1 MACWD1 0 0 MACWD0 0
Bits 0 - 7: MAC Write Data 0 (MACWD0-7) One of four bytes of data to be written to the MAC. Data has been written after a write command has been issued and the SU.MACRWC.MCS bit is zero.
171 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default SU.MACWD1 MAC Write Data 1 147h
7 6 5 4 3 2 1 0 MACWD15 MACWD14 MACWD13 MACWD12 MACWD11 MACWD10 MACWD09 MACWD08 0 0 0 0 0 0 0 0
Bits 0 - 7: MAC Write Data 1 (MACWD8-15) One of four bytes of data to be written to the MAC. Data has been written after a write command has been issued and the SU.MACRWC.MCS bit is zero. Register Name: Register Description: Register Address: Bit # Name SU.MACWD2 MAC Write Data Register 2 148h
7 6 5 4 3 2 1 0 MACWD23 MACWD22 MACWD21 MACWD20 MACWD19 MACWD18 MACWD17 MACWD16 0 0 0 0 0 0 0 0
Bits 0 - 7: MAC Write Data 2 (MACWD16-23) One of four bytes of data to be written to the MAC. Data has been written after a write command has been issued and the SU.MACRWC.MCS bit is zero.
Register Name: Register Description: Register Address: Bit # Name 7 MACD31 0
SU.MACWD3 MAC Write Data 3 149h 6 MACD30 0 5 MACD29 0 4 MACD28 0 3 MACD27 0 2 MACD26 0 1 MACD25 0 0 MACD24 0
Bits 0 - 7: MAC Write Data 3 (MACD24-31) One of four bytes of data to be written to the MAC. Data has been written after a write command has been issued and the SU.MACRWC.MCS bit is zero. Register Name: Register Description: Register Address: Bit # Name 7 MACAW 7 0 SU.MACAWL MAC Address Write Low 14Ah 6 MACAW 6 0 5 MACAW 5 0 4 MACAW4 0 3 MACAW3 0 2 MACAW2 0 1 MACAW1 0 0 MACAW0 0
Bits 0 -7: MAC Write Address (MACAW0-7) Low byte of the MAC indirect write address. Used only for write operations.
172 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name SU.MACAWH MAC Address Write High 14Bh 1 MACAW9 0 0 MACAW8 0
7 6 5 4 3 2 MACAW 15 MACAW 14 MACAW 13 MACAW12 MACAW11 MACAW10 0 0 0 0 0 0
Bits 0 - 7: MAC Write Address (MACAW8-15) High byte of the MAC indirect write address. Used only for write operations.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
SU.MACRWC MAC Read Write Command Status 14Ch 5 0 4 0 3 0 2 0 1 MCRW 0 0 MCS 0
Bit 1: MAC Command RW (MCRW) If this bit is written to 1, a read is performed from the MAC. If this bit is written to 0, a write operation is performed. Address information for write operations must be located in SU.MACAWH and SU.MACAWL. Address information for read operations must be located in SU.MACRADH and SU.MACRADL. The user must also write a 1 to the MCS bit, and the DS33R11 will clear MCS when the operation is complete. Bit 0: MAC Command Status (MCS) Setting MCS in conjunction with MCRW will initiate a read or write to the MAC registers. Upon completion of the read or write this bit is cleared. Once a read or write command has been initiated the host must poll this bit to see when the operation is complete.
173 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 SU.LPBK Ethernet Interface Loopback Control Register 14Fh 5 0 4 0 3 0 2 0 1 0 0 QLP 0
Bit 0: Queue Loopback Enable (QLP) If this bit is set to 1, data from the Ethernet Interface receive queue is looped back to the transmit queue. Buffered data from the serial interface will remain until the loopback is removed.
Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0
SU.GCR Ethernet Interface General Control Register 150h 5 0 4 0 3 CRCS 0 2 H10S 0 1 ATFLOW 1 0 JAME 0
Bit 3: CRCS If this bit is zero (default), the received MAC or Ethernet Frame CRC is stripped before the data is encapsulated and transmitted on the serial interface. Data received from the serial interface is decapsulated, a CRC is recalculated and appended to the packet for transmission to the Ethernet interface. If this bit is set to 1, the CRC is not stripped from received packets prior to encapsulation and transmission to the serial interface, and data received from the serial interface is decapsulated directly. No CRC recalculation is performed on data received from the serial interface. Note that the maximum packet size supported by the Ethernet interface is still 2016 (this includes the 4 bytes of CRC). Bit 2: H10S If this bit is set the MAC will operate at 100 Mbit/s. If this bit is zero, the MAC will operate at 10 Mbit/s. This bit controls the 10/100 selection for RMII and DCE Mode. In DTE and MII mode, the MAC determines the data rate from the incoming TX_CLK and RX_CLK. Bit 1: Automatic Flow Control Enable (ATFLOW) If this bit is set to 1, automatic flow control is enabled based on the connection receive queue size and high watermarks. Pause frames are sent automatically in full duplex mode. The pause time must be programmed through SU.MACFCR. The jam sequence will not be sent automatically in half duplex mode unless the JAME bit is set. This bit is applicable only in software mode. Bit 0: Jam Enable (JAME) If this bit is set to 1, a Jam sequence is sent for a duration of 4 bytes. This function is only valid in half duplex mode, and will only function if Automatic Flow Control is disabled. Note that if the receive queue size is less than receive high threshold, setting a JAME will JAM one received frame. If JAME is set and the receiver queue size is higher than the high threshold, all received frames are jammed until the queue empties below the threshold. Note that SU.GCR is only valid in the software mode.
174 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 SU.TFRC Transmit Frame Resend Control 151h 5 0 4 0 3 NCFQ 0 2 TPDFCB 0 1 TPRHBC 0 0 TPRCB 0
Bit 3: No Carrier Queue Flush Bar (NCFQ) If this bit is set to 1, the queue for data passing from Serial Interface to Ethernet Interface will not be flushed when loss of carrier is detected. Bit 2: Transmit Packet Deferred Fail Control Enable (TPDFCB) If this bit if set to 1, the current frame is transmitted immediately instead of being deferred. If this bit is set to 0, the frame is deferred if CRS is asserted and sent when the CRS is unasserted indicating the media is idle. Bit 1: Transmit Packet HB Fail Control Bar (TPRHBC) If this bit is set to 1, the current frame will not be retransmitted if a heartbeat failure is detected. Bit 0: Transmit Packet Resend Control Bar (TPRCB) If this bit is set to 1, the current frame will not be retransmitted if any of the following errors have occurred: * * * * * * * Jabber time out Loss of carrier Excessive deferral Late collision Excessive collisions Under run Collision
Note that blocking retransmission due to collision (applicable in MIII/Half Duplex Mode) can result in unpredictable system level behavior.
175 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 UR 0 6 EC 0
SU.TFSL Transmit Frame Status Low 152h 5 LC 0 4 ED 0 3 LOC 0 2 NOC 0 1 0 0 FABORT 0
Bit 7: Under Run (UR) When this bit is set to 1, the frame was aborted due to a data under run condition of the transmit buffer. Bit 6: Excessive Collisions (EC) When this bit is set to 1, a frame has been aborted after 16 successive collisions while attempting to transmit the current frame. If the Disable Retry bit is set to 1, then Excessive Collisions will be set to 1 after the first collision. Bit 5: Late Collision (LC) When this bit is set to 1, a frame was aborted by collision after the 64 bit collision window. Not valid if an under run has occurred. Bit 4: Excessive Deferral (ED) When this bit is set to 1, a frame was aborted due to excessive deferral. Bit 3: Loss Of Carrier (LOC) When this bit is set to 1, a frame was aborted due to loss of carrier for one or more bit times. Valid only for noncollided frames. Valid only in half-duplex operation. Bit 2: No Carrier (NOC) When this bit is set to 1, a frame was aborted because no carrier was found for transmission. Bit 1: Reserved Bit 0: Frame Abort (FABORT) When this bit is set to 1, the MAC has aborted a frame for one of the above reasons. When this bit is clear, the previous frame has been transmitted successfully. Register Name: Register Description: Register Address: Bit # Name Default 7 PR 0 6 HBF 0 SU.TFSH Transmit Frame Status High 153h 5 CC3 0 4 CC2 0 3 CC1 0 2 CC0 0 1 LCO 0 0 DEF 0
Bit 7: Packet Resend (PR) When this bit is set, the current packet must be retransmitted due to a collision. Bit 6: Heartbeat Failure (HBF) When this bit is set, the device failed to detect a heart beat after transmission. This bit is not valid if an under run has occurred. Bits 2-5: Collision Count (CC0-3) These 4 bits indicate the number of collisions that occurred prior to successful transmission of the previous frame. Not valid if Excessive Collisions is set to 1. Bit 1: Late Collision (LCO) When set to 1, the MAC observed a collision after the 64-byte collision window. Bit 0: Deferred Frame (DEF) When set to 1, the current frame was deferred due to carrier assertion by another node after being ready to transmit.
176 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 FL7 0 6 FL6 0 SU.RFSB0 Receive Frame Status Byte 0 154h 5 FL5 0 4 FL4 0 3 FL3 0 2 FL2 0 1 FL1 0 0 FL0 0
Bits 0 - 7: Frame Length (FL[0:7]) These 8 bits are the low byte of the length (in bytes) of the received frame, with FCS and Padding. If Automatic Pad Stripping is enabled, this value is the length of the received packet without PCS or Pad bytes. The upper 6 bits are contained in SU.RFSB1. Register Name: Register Description: Register Address: Bit # Name Default 7 RF 0 6 WT 0 SU.RFSB1 Receive Frame Status Byte 1 155h 5 FL13 0 4 FL12 0 3 FL11 0 2 FL10 0 1 FL9 0 0 FL8 0
Bit 7: Runt Frame (RF) This bit is set to 1 if the received frame was altered by a collision or terminated within the collision window. Bit 6: Watchdog Timeout (WT) This bit is set to 1 if a packet receive time exceeds 2048 byte times. After 2048 byte times the receiver is disabled and the received frame will fail CRC check. Bits 0-5: Frame Length (FL[8:13]) These 6 bits are the upper bits of the length (in bytes) of the received frame, with FCS and Padding. If Automatic Pad Stripping is enabled, this value is the length of the received packet without PCS or Pad bytes. Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 SU.RFSB2 Receive Frame Status Byte 2 156h 5 CRCE 0 4 DB 0 3 MIIE 0 2 FT 0 1 CS 0 0 FTL 0
Bit 5: CRC Error (CRCE) This bit is set to 1 if the received frame does not contain a valid CRC value. Bit 4: Dribbling Bit (DB) This bit is set to 1 if the received frame contains a noninteger multiple of 8 bits. It does not indicate that the frame is invalid. This bit is not valid for runt or collided frames. Bit 3: MII Error (MIIE) This bit is set to 1 if an error was found on the MII bus. Bit 2: Frame Type (FT) This bit is set to 1 if the received frame exceeds 1536 bytes. It is equal to zero if the received frame is an 802.3 frame. This bit is not valid for runt frames. Bit 1: Collision Seen (CS) This bit is set to 1 if a late collision occurred on the received packet. A late collision is one that occurs after the 64 byte collision window. Bit 0: Frame Too Long (FTL) This bit is set to 1 if a frame exceeds the 1518 byte maximum standard Ethernet frame. This bit is only an indication, and causes no frame truncation.
177 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 MF 0 6 0 SU.RFSB3 Receive Frame Status Byte 3 157h 5 0 4 BF 0 3 MCF 0 2 UF 0 1 CF 0 0 LE 0
Bit 7: Missed Frame (MF) This bit is set to 1 if the packet is not successfully received from the MAC by the packet Arbiter. Bit 4: Broadcast Frame (BF) This bit is set to 1 if the current frame is a broadcast frame. Bit 3: Multicast Frame (MCF) This bit is set to 1 if the current frame is a multicast frame. Bit 2: Unsupported Control Frame (UF) This bit is set to 1 if the frame received is a control frame with an opcode that is not supported. If the Control Frame bit is set, and the Unsupported Control Frame bit is clear, then a pause frame has been received and the transmitter is paused. Bit 1: Control Frame (CF) This bit is set to 1 when the current frame is a control frame. This bit is only valid in fullduplex mode. Bit 0: Length Error (LE) This bit is set to 1 when the frames length field and the actual byte count are unequal. This bit is only valid for 802.3 frames.
178 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RMPS7 1 6 RMPS6 1
SU.RMFSRL Receiver Maximum Frame Low Register 158h 5 RMPS5 1 4 RMPS4 0 3 RMPS3 0 2 RMPS2 0 1 RMPS1 1 0 RMPS0 0
Bits 7- 0: Receiver Maximum Frame (RMPS[0:7]) Eight bits of sixteen bit value. Register description below.
Register Name: Register Description: Register Address: Bit # Name Default 7 RMPS15 0
SU.RMFSRH Receiver Maximum Frame High Register 159h 6 RMPS14 0 5 RMPS13 0 4 RMPS12 0 3 RMPS11 0 2 RMPS10 1 1 RMPS9 1 0 RMPS8 1
Bits 7- 0: Receiver Maximum Frame (RMPS[8:15]) This value is the receiver's maximum frame size (in bytes), up to a maximum of 2016 bytes. Any frame received greater than this value is rejected. The frame size includes destination address, source address, type/length, data and crc-32. The frame size is not the same as the frame length encoded within the IEEE 802.3 frame. Any values programmed that are greater than 2016 will have unpredictable behavior and should be avoided.
Register Name: Register Description: Register Address: Bit # Name Default 7 RQLT7 0 6 RQLT6 0
SU.RQLT Receive Queue Low Threshold (Watermark) 15Ah 5 RQLT5 1 4 RQLT4 1 3 RQLT3 0 2 RQLT2 1 1 RQLT1 1 0 RQLT0 1
Bits 0 - 7: Receive Queue Low Threshold (RQLT[0:7]) The receive queue low threshold for the connection, in increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to determine the byte location of the threshold. Note that the receive queue is for data that was received from the Ethernet Interface to be sent to the Serial Interface.
Register Name: Register Description: Register Address: Bit # Name Default 7 RQHT7 0 6 RQHT6 0
SU.RQHT Receive Queue High Threshold (Watermark) 15Bh 5 RQHT5 1 4 RQHT4 1 3 RQHT3 1 2 RQHT2 0 1 RQHT1 1 0 RQHT0 0
Bits 0 - 7: Receive Queue High Threshold (RQTH[0:7]) The receive queue high threshold for the connection, in increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to determine the byte location of the threshold. Note that the receive queue is for data that was received from the Ethernet Interface to be sent to the Serial Interface.
179 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 0 SU.QRIE Receive Queue Cross Threshold enable 15Ch 5 0 4 0 3 RFOVFIE 0 2 RQVFIE 0 1 RQLTIE 0 0 RQHTIE 0
Bit 3: Receive FIFO Overflow Interrupt Enable (RFOVFIE) If this bit is set, the interrupt is enabled for RFOVFLS. Bit 2: Receive Queue Overflow Interrupt Enable (RQVFIE) If this bit is set, the interrupt is enabled for RQOVFLS. Bit 1: Receive Queue Crosses Low Threshold Interrupt Enable (RQLTIE) If this bit is set, the watermark interrupt is enabled for RQLTS. Bit 0: Receive Queue Crosses High Threshold Interrupt Enable (RQHTIE) If this bit is set, the watermark interrupt is enabled for RQHTS. Register Name: Register Description: Register Address: Bit # Name Default 7 6 SU.QCRLS Queue Cross Threshold Latched Status 15Dh 5 4 3 RFOVFLS 2 RQOVFLS 1 RQHTLS 0 RQLTLS -
Bit 3: Receive FIFO Overflow latched Status (RFOVFLS) This bit is set if the receive FIFO overflows for the data to be transmitted from the MAC to the SDRAM. Bit 2: Receive Queue Overflow Latched Status (RQOVFLS) This bit is set if the receive queue has overflowed. This register is cleared after a read. Bit 1: Receive Queue for Connection Crossed High Threshold Latched Status (RQHTLS) This bit is set if the receive queue crosses the high Watermark. This register is cleared after a read. Bit 0: Receive Queue for Connection Crossed Low Threshold latched status (RQLTLS) This bit is set if the receive queue crosses the low Watermark. This register is cleared after a read. Note the bit order differences in the high/low threshold indications in SU.QCRLS and the interrupt enables in SU.QRIE.
180 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 6 UCFR 0 SU.RFRC Receive Frame Rejection Control 15Eh 5 CFRR 0 4 LERR 0 3 CRCERR 0 2 DBR 0 1 MIIER 0 0 BFR 0
Bit 6: Uncontrolled Control Frame Reject (UCFR) When set to 1, Control Frames other than Pause Frames are allowed. When this bit is equal to zero, nonpause control frames are rejected. Bit 5: Control Frame Reject (CFRR) When set to 1, control frames are allowed. When this bit is equal to zero, all control frames are rejected. Bit 4: Length Error Reject (LERR) When set to 1, frames with an unmatched frame length field and actual number of bytes received are allowed. When equal to zero, only frames with matching length fields and actual bytes received will be allowed. Bit 3: CRC Error Reject (CRCERR) When set to 1, frames received with a CRC error or MII error are allowed. When equal to zero, frames with CRC or MII errors are rejected. Bit 2: Dribbling Bit Reject (DBR) When set to 1, frames with lengths of noninteger multiples of 8 bits are allowed. When equal to zero, frames with dribbling bits are rejected. The dribbling bit setting is only valid only if there is not a collision or runt frame. Bit 1: MII Error Reject (MIIER) When set to 1, frames are allowed with MII Receive Errors. When equal to zero, frames with MII errors are rejected. Bit 0: Broadcast Frame Reject (BFR) When set to 1, broadcast frames are allowed. When equal to zero, broadcast frames are rejected.
181 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.6.2 MAC Registers
The control Registers related to the control of the individual Mac's are shown in the following Table. The DS33R11 keeps statistics for the packet traffic sent and received. The register address map is shown in the following Table. Note that the addresses listed are the indirect addresses that must be provided to SU.MACRADH/SU.MACRADL or SU.MACAWH/SU.MACAWL. Register Name: Register Description: Register Address: 0000h: Bit # Name Default 0001h: Bit # Name Default 0002h: Bit # Name Default 0003h: Bit # Name Default SU.MACCR MAC Control Register 0000h (indirect)
31 Reserved 0 23 DRO 0 15 Reserved 0 07 BOLMT1 0
30 Reserved 0 22 Reserved 0 14 Reserved 0 06 BOLMT0 0
29 Reserved 0 21 OML0 0 13 Reserved 0 05 DC 0
28 HDB 0 20 F 0 12 LCC 0 04 Reserved 0
27 PS 0 19 Reserved 0 11 Reserved 0 03 TE 0
26 Reserved 0 18 Reserved 0 10 DRTY 0 02 RE 0
25 Reserved 0 17 Reserved 0 09 Reserved 0 01 Reserved 0
24 Reserved 0 16 Reserved 0 08 ASTP 0 00 Reserved 0
Bit 28: Heartbeat Disable (HDB) When set to 1, the heartbeat (SQE) function is disabled. This bit should be set to 1 when operating in MII mode. Bit 27: Port Select (PS) This bit should be equal to 0 for proper operation. Bit 23: Disable Receive Own (DRO) When set to 1, the MAC disables the reception of frames while TX_EN is asserted. When this bit equals zero, transmitted frames are also received by the MAC. This bit should be cleared when operating in full-duplex mode. Bit 21: Loopback Operating Mode (OMLO) When set to 1, data is looped from the transmit side, back to the receive side, without being transmitted to the PHY. Bit 20: Full-Duplex Mode Select (F) When set to 1, the MAC transmits and receives data simultaneously. When in full-duplex mode, the heartbeat check is disabled and the heartbeat fail status should be ignored.
182 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Bit 12: Late Collision Control (LCC) When set to 1, enables retransmission of a collided packet even after the collision period. When this bit is clear, retransmission of late collisions is disabled. Bit 10: Disable Retry (DRTY) When set to 1, the MAC makes only a single attempt to transmit each frame. If a collision occurs, the MAC ignores the current frame and proceeds to the next frame. When this bit equals 0, the MAC will retry collided packets 16 times before signaling a retry error. Bit 8: Automatic Pad Stripping (ASTP) When set to 1, all incoming frames with less than 46 byte length are automatically stripped of the pad characters and FCS. Bits 6 - 7: Back-Off Limit (BOLMT[0:1]) These two bits allow the user to set the back-off limit used for the maximum retransmission delay for collided packets. Default operation limits the maximum delay for retransmission to a countdown of 10 bits from a random number generator. The user can reduce the maximum number of counter bits as described in the table below. See IEEE 802.3 for details of the back-off algorithm. Bit 7 0 0 1 1 Bit 6 0 1 0 1 Random Number Generator Bits Used 10 8 4 1
Bit 5: Deferral Check (DC) When set to 1, the MAC will abort packet transmission if it has deferred for more than 24,288 bit times. The deferral counter starts when the transmitter is ready to transmit a packet, but is prevented from transmission because CRS is active. If the MAC begins transmission but a collision occurs after the beginning of transmission, the deferral counter is reset again. If this bit is equal to zero, then the MAC will defer indefinitely. Bit 3: Transmitter Enable (TE) When set to 1, packet transmission is enabled. When equal to zero, transmission is disabled. Bit 2: Receiver Enable (RE) When set to 1, packet reception is enabled. When equal to zero, packets are not received.
183 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: 0014h: Bit # Name Default 0015h: Bit # Name Default 0016h: Bit # Name Default 0017h: Bit # Name Default SU.MACMIIA MAC MII Management (MDIO) Address Register 0014h (indirect)
31 Reserved 0 23 Reserved 0 15 PHYA4 0 07 MIIA1 1
30 Reserved 0 22 Reserved 0 14 PHYA3 1 06 MIIA0 1
29 Reserved 0 21 Reserved 0 13 PHYA2 0 05 Reserved 0
28 Reserved 0 20 Reserved 0 12 PHYA1 1 04 Reserved 0
27 Reserved 0 19 Reserved 0 11 PHYA0 1 03 Reserved 0
26 Reserved 0 18 Reserved 0 10 MIIA4 0 02 Reserved 0
25 Reserved 0 17 Reserved 0 09 MIIA3 1 01 MIIW 0
24 Reserved 0 16 Reserved 0 08 MIIA2 0 00 MIIB 0
Bits 11 - 15: PHY Address (PHYA[0:4]) These 5 bits select one of the 32 available PHY address locations to access through the PHY management (MDIO) bus. Bits 6 - 10: MII Address (MIIA[0:4]) - These 5 bits are the address location within the PHY that is being accessed. Bit 1: MII Write (MIIW) Write this bit to 1 in order to execute a write instruction over the MDIO interface. Write the bit to zero to execute a read instruction. Bit 0: MII Busy (MIIB) This bit is set to 1 by the DS33R11 during execution of a MII management instruction through the MDIO interface, and is set to zero when the DS33R11 has completed the instruction. The user should read this bit and ensure that it is equal to zero prior to beginning a MDIO instruction.
184 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0018h: Bit # Name Default 0019h: Bit # Name Default 001Ah: Bit # Name Default 001Bh: Bit # Name Default
SU.MACMIID MAC MII (MDIO) Data Register 0018h (indirect)
31 Reserved 0 23 Reserved 0 15 MIID15 0 07 MIID07 0
30 Reserved 0 22 Reserved 0 14 MIID14 0 06 MIID06 0
29 Reserved 0 21 Reserved 0 13 MIID13 0 05 MIID05 0
28 Reserved 0 20 Reserved 0 12 MIID12 0 04 MIID04 0
27 Reserved 0 19 Reserved 0 11 MIID11 0 03 MIID03 0
26 Reserved 0 18 Reserved 0 10 MIID10 0 02 MIID02 0
25 Reserved 0 17 Reserved 0 09 MIID09 0 01 MIID01 0
24 Reserved 0 16 Reserved 0 08 MIID08 0 00 MIID00 0
Bits 0 - 15: MII (MDIO) Data (MIID[00:15]) These two bytes contain the data to be written to or the data read from the MII management interface (MDIO).
185 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 001Ch: Bit # Name Default 001Dh: Bit # Name Default 001Eh: Bit # Name Default 001Fh: Bit # Name Default
SU.MACFCR MAC Flow Control Register 001Ch (indirect)
31 PT15 0 23 PT07 0 15 Reserved 0 07 Reserved 0
30 PT14 0 22 PT06 1 14 Reserved 0 06 Reserved 0
29 PT13 0 21 PT05 0 13 Reserved 0 05 Reserved 0
28 PT12 0 20 PT04 1 12 Reserved 0 04 Reserved 0
27 PT11 0 19 PT03 0 11 Reserved 0 03 Reserved 0
26 PT10 0 18 PT02 0 10 Reserved 0 02 Reserved 0
25 PT09 0 17 PT01 0 09 Reserved 0 01 FCE 1
24 PT08 0 16 PT00 0 08 Reserved 0 00 FCB 0
Bits 16 - 31: Pause Time (PT[00:15]) These bits are used for the Pause Time Field in transmitted Pause Frames. This value is the number of time slots the remote node should wait prior to transmission. Bit 1: Flow Control Enable (FCE) When set to 1, the MAC automatically detects pause frames and will disable the transmitter for the requested pause time. Bit 0: Flow Control Busy (FCB) The host can set this bit to 1 in order to initiate transmission of a pause frame. During transmission of a pause frame, this bit remains set. The DS33R11 will clear this bit when transmission of the pause frame has been completed. The user should read this bit and ensure that this bit is equal to zero prior to initiating a pause frame.
186 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0100h: Bit # Name Default 0101h: Bit # Name Default 0102h: Bit # Name Default 0103h: Bit # Name Default
SU.MMCCTRL MAC MMC Control Register 0100h (indirect)
31 Reserved 0 23 Reserved 0 15 Reserved 0 07 MXFRM4 0
30 Reserved 0 22 Reserved 0 14 Reserved 0 06 MXFRM3 1
29 Reserved 0 21 Reserved 0 13 MXFRM10 1 05 MXFRM2 1
28 Reserved 0 20 Reserved 0 12 MXFRM9 0 04 MXFRM1 1
27 Reserved 0 19 Reserved 0 11 MXFRM8 1 03 MXFRM0 0
26 Reserved 0 18 Reserved 0 10 MXFRM7 1 02 Reserved 0
25 Reserved 0 17 Reserved 0 09 MXFRM6 1 01 Reserved 1
24 Reserved 0 16 Reserved 0 08 MXFRM5 1 00 Reserved 0
Bits 3 - 13: Maximum Frame Size (MXFRM[0:10]) These bits indicate the maximum packet size value. All transmitted frames larger than this value are counted as long frames. Bit 1: Reserved - Note that this bit must be written to a "1" for proper operation.
187 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 010Ch: Bit # Name Default 010Dh: Bit # Name Default 010Eh: Bit # Name Default 010Fh: Bit # Name Default
Reserved MAC Reserved Control Register 010Ch (indirect)
31 Reserved 0 23 Reserved 0 15 Reserved 0 07 Reserved 0
30 Reserved 0 22 Reserved 0 14 Reserved 0 06 Reserved 0
29 Reserved 0 21 Reserved 0 13 Reserved 0 05 Reserved 0
28 Reserved 0 20 Reserved 0 12 Reserved 0 04 Reserved 0
27 Reserved 0 19 Reserved 0 11 Reserved 0 03 Reserved 0
26 Reserved 0 18 Reserved 0 10 Reserved 0 02 Reserved 0
25 Reserved 0 17 Reserved 0 09 Reserved 0 01 Reserved 0
24 Reserved 0 16 Reserved 0 08 Reserved 0 00 Reserved 0
Note - Addresses 10Ch through 10Fh must each be initialized with all 1's (FFh) for proper software-mode operation.
188 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0110h: Bit # Name Default 0111h: Bit # Name Default 0112h: Bit # Name Default 0113h: Bit # Name Default
Reserved MAC Reserved Control Register 0110h (indirect)
31 Reserved 0 23 Reserved 0 15 Reserved 0 07 Reserved 0
30 Reserved 0 22 Reserved 0 14 Reserved 0 06 Reserved 0
29 Reserved 0 21 Reserved 0 13 Reserved 0 05 Reserved 0
28 Reserved 0 20 Reserved 0 12 Reserved 0 04 Reserved 0
27 Reserved 0 19 Reserved 0 11 Reserved 0 03 Reserved 0
26 Reserved 0 18 Reserved 0 10 Reserved 0 02 Reserved 0
25 Reserved 0 17 Reserved 0 09 Reserved 0 01 Reserved 0
24 Reserved 0 16 Reserved 0 08 Reserved 0 00 Reserved 0
Note - Addresses 110h through 113h must each be initialized with all 1's (FFh) for proper software-mode operation.
189 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0200h: Bit # Name Default 0201h: Bit # Name Default 0202h: Bit # Name Default 0203h: Bit # Name Default
SU.RxFrmCtr MAC All Frames Received Counter 0200h (indirect)
31
RXFRMC31
30
RXFRMC30
29
RXFRMC29
28
RXFRMC28
27
RXFRMC27
26
RXFRMC26
25
RXFRMC25
24
RXFRMC24
0 23
RXFRMC23
0 22
RXFRMC22
0 21
RXFRMC21
0 20
RXFRMC20
0 19
RXFRMC19
0 18
RXFRMC18
0 17
RXFRMC17
0 16
RXFRMC16
0 15
RXFRMC15
0 14
RXFRMC14
0 13
RXFRMC13
0 12
RXFRMC12
0 11
RXFRMC11
0 10
RXFRMC10
0 09
RXFRMC9
0 08
RXFRMC8
0 07
RXFRMC7
0 06
RXFRMC6
0 05
RXFRMC5
0 04
RXFRMC4
0 03
RXFRMC3
0 02
RXFRMC2
0 01
RXFRMC1
0 00
RXFRMC0
0
0
0
0
0
0
0
0
Bits 0 - 31: All Frames Received Counter (RXFRMC[0:31]) 32 bit value indicating the number of frames received. Each time a frame is received, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
190 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0204h: Bit # Name Default 0205h: Bit # Name Default 0206h: Bit # Name Default 0207h: Bit # Name Default
SU.RxFrmOkCtr MAC Frames Received OK Counter 0204h (indirect)
31 0 23 0 15 0 07 0
30 0 22 0 14 0 06 0
29 0 21 0 13 0 05 0
28 0 20 0 12 0 04 0
27 0 19 0 11 0 03 0
26 0 18 0 10 0 02 0
25 0 17 0 09 0 01 0
24 0 16 0 08 0 00 0
RXFRMOK31 RXFRMOK30 RXFRMOK29 RXFRMOK28 RXFRMOK27 RXFRMOK26 RXFRMOK25 RXFRMOK24
RXFRMOK23 RXFRMOK22 RXFRMOK21 RXFRMOK20 RXFRMOK19 RXFRMOK18 RXFRMOK17 RXFRMOK16
RXFRMOK15 RXFRMOK14 RXFRMOK13 RXFRMOK12 RXFRMOK11 RXFRMOK10 RXFRMOK9 RXFRMOK8
RXFRMOK7 RXFRMOK6 RXFRMOK5 RXFRMOK4 RXFRMOK3 RXFRMOK2 RXFRMOK1 RXFRMOK0
Bits 0 - 31: Frames Received OK Counter (RXFRMOK[0:31]) 32 bit value indicating the number of frames received and determined to be valid. Each time a valid frame is received, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
191 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0300h: Bit # Name Default 0301h: Bit # Name Default 0302h: Bit # Name Default 0303h: Bit # Name Default
SU.TxFrmCtr MAC All Frames Transmitted Counter 0300h (indirect)
31
TXFRMC31
30
TXFRMC30
29
TXFRMC29
28
TXFRMC28
27
TXFRMC27
26
TXFRMC26
25
TXFRMC25
24
TXFRMC24
0 23
TXFRMC23
0 22
TXFRMC22
0 21
TXFRMC21
0 20
TXFRMC20
0 19
TXFRMC19
0 18
TXFRMC18
0 17
TXFRMC17
0 16
TXFRMC16
0 15
TXFRMC15
0 14
TXFRMC14
0 13
TXFRMC13
0 12
TXFRMC12
0 11
TXFRMC11
0 10
TXFRMC10
0 09
TXFRMC9
0 08
TXFRMC8
0 07
TXFRMC7
0 06
TXFRMC6
0 05
TXFRMC5
0 04
TXFRMC4
0 03
TXFRMC3
0 02
TXFRMC2
0 01
TXFRMC1
0 00
TXFRMC0
0
0
0
0
0
0
0
0
Bits 0 - 31: All Frames Transmitted Counter (TXFRMC[0:31]) 32 bit value indicating the number of frames transmitted. Each time a frame is transmitted, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
192 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0308h: Bit # Name Default 0309h: Bit # Name Default 030Ah: Bit # Name Default 030Bh: Bit # Name Default
SU.TxBytesCtr MAC All Bytes Transmitted Counter 0308h (indirect)
31 0 23 0 15 0 07
TXBYTEC7
30 0 22 0 14 0 06
TXBYTEC6
29 0 21 0 13 0 05
TXBYTEC5
28 0 20 0 12 0 04
TXBYTEC4
27 0 19 0 11 0 03
TXBYTEC3
26 0 18 0 10 0 02
TXBYTEC2
25 0 17 0 09 0 01
TXBYTEC1
24 0 16 0 08
TXBYTEC8
TXBYTEC31 TXBYTEC30 TXBYTEC29 TXBYTEC28 TXBYTEC27 TXBYTEC26 TXBYTEC25 TXBYTEC24
TXBYTEC23 TXBYTEC22 TXBYTEC21 TXBYTEC20 TXBYTEC19 TXBYTEC18 TXBYTEC17 TXBYTEC16
TXBYTEC15 TXBYTEC14 TXBYTEC13 TXBYTEC12 TXBYTEC11 TXBYTEC10 TXBYTEC9
0 00
TXBYTEC0
0
0
0
0
0
0
0
0
Bits 0 - 31: All Bytes Transmitted Counter (TXBYTEC[0:31]) 32 bit value indicating the number of bytes transmitted. Each time a byte is transmitted, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum data rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
193 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 030Ch: Bit # Name Default 030Dh: Bit # Name Default 030Eh: Bit # Name Default 030Fh: Bit # Name Default
SU.TxBytesOkCtr MAC Bytes Transmitted OK Counter 030Ch (indirect)
31 0 23 0 15 0 07
TXBYTEOK7
30 0 22 0 14 0 06
TXBYTEOK6
29 0 21 0 13 0 05
TXBYTEOK5
28 0 20 0 12 0 04
TXBYTEOK4
27 0 19 0 11 0 03
TXBYTEOK3
26 0 18 0 10 0 02
TXBYTEOK2
25 0 17 0 09
TXBYTEOK9
24 0 16 0 08
TXBYTEOK8
TXBYTEOK31 TXBYTEOK30 TXBYTEOK29 TXBYTEOK28 TXBYTEOK27 TXBYTEOK26 TXBYTEOK25 TXBYTEOK24
TXBYTEOK23 TXBYTEOK22 TXBYTEOK21 TXBYTEOK20 TXBYTEOK19 TXBYTEOK18 TXBYTEOK17 TXBYTEOK16
TXBYTEOK15 TXBYTEOK14 TXBYTEOK13 TXBYTEOK12 TXBYTEOK11 TXBYTEOK10
0 01
TXBYTEOK1
0 00
TXBYTEOK0
0
0
0
0
0
0
0
0
Bits 0 - 31: Bytes Transmitted OK Counter (TXBYTEOK[0:31]) 32 bit value indicating the number of bytes transmitted and determined to be valid. Each time a valid byte is transmitted, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
194 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0334h: Bit # Name Default 0335h: Bit # Name Default 0336h: Bit # Name Default 0337h: Bit # Name Default
SU.TXFRMUNDR MAC Transmit Frame Under Run Counter 0334h (indirect)
31
TXFRMU31
30
TXFRMU30
29
TXFRMU29
28
TXFRMU28
27
TXFRMU27
26
TXFRMU26
25
TXFRMU25
24
TXFRMU24
0 23
TXFRMU23
0 22
TXFRMU22
0 21
TXFRMU21
0 20
TXFRMU20
0 19
TXFRMU19
0 18
TXFRMU18
0 17
TXFRMU17
0 16
TXFRMU16
0 15
TXFRMU15
0 14
TXFRMU14
0 13
TXFRMU13
0 12
TXFRMU12
0 11
TXFRMU11
0 10
TXFRMU10
0 09
TXFRMU9
0 08
TXFRMU8
0 07
TXFRMU7
0 06
TXFRMU6
0 05
TXFRMU5
0 04
TXFRMU4
0 03
TXFRMU3
0 02
TXFRMU2
0 01
TXFRMU1
0 00
TXFRMU0
0
0
0
0
0
0
0
0
Bits 0 - 31: Frames Aborted Due to FIFO Under Run Counter (TXFRMU[0:31]) 32 bit value indicating the number of frames aborted due to FIFO under run. Each time a frame is aborted due to FIFO under run, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
195 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: 0338h: Bit # Name Default 0339h: Bit # Name Default 033Ah: Bit # Name Default 033Bh: Bit # Name Default
SU.TxBdFrmCtr MAC All Frames Aborted Counter 0338h (indirect)
31 0 23 0 15 0 07
TXFRMBD7
30 0 22 0 14 0 06
TXFRMBD6
29 0 21 0 13 0 05
TXFRMBD5
28 0 20 0 12 0 04
TXFRMBD4
27 0 19 0 11 0 03
TXFRMBD3
26 0 18 0 10 0 02
TXFRMBD2
25 0 17 0 09 0 01
TXFRMBD1
24 0 16 0 08
TXFRMBD8
TXFRMBD31 TXFRMBD30 TXFRMBD29 TXFRMBD28 TXFRMBD27 TXFRMBD26 TXFRMBD25 TXFRMBD24
TXFRMBD23 TXFRMBD22 TXFRMBD21 TXFRMBD20 TXFRMBD19 TXFRMBD18 TXFRMBD17 TXFRMBD16
TXFRMBD15 TXFRMBD14 TXFRMBD13 TXFRMBD12 TXFRMBD11 TXFRMBD10 TXFRMBD9
0 00
TXFRMBD0
0
0
0
0
0
0
0
0
Bits 0 to 31: All Frames Aborted Counter (TXFRMBD[0:31]) 32 bit value indicating the number of frames aborted due to any reason. Each time a frame is aborted, this counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
196 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.7 T1/E1/J1 Transceiver Registers
Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.MSTRREG Master Mode Register 00h 6 -- 0 5 -- 0 4 -- 0 3 TEST1 0 2 TEST0 0 1 T1/E1 0 0 SFTRST 0
Bits 2 - 3: Test Mode Bits (TEST0, TEST1) Test modes are used to force the output pins of the transceiver into known states. This can facilitate the checkout of assemblies during the manufacturing process and also be used to isolate devices from shared buses. TEST1 0 0 1 1 TEST0 0 1 0 1 Operate normally Force all output pins into tri-state (including all I/O pins and parallel port pins) Force all output pins low (including all I/O pins except parallel port pins) Force all output pins high (including all I/O pins except parallel port pins) Effect On Output Pins
Bit 1: Transceiver Operating Mode (T1/E1) Used to select the operating mode of the framer/formatter (digital) portion of the Transceiver. The operating mode of the LIU must also be programmed. 0 = T1 operation 1 = E1 operation Bit 0: Software-Issued Reset (SFTRST) A 0-to-1 transition causes the register space in the T1/E1/J1 transceiver to be cleared. A reset clears all configuration and status registers. The bit automatically clears itself when the reset has completed.
197 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RSMS 0 TR.IOCR1 I/O Configuration Register 1 01h 6 RSMS2 0 5 RSMS1 0 4 RSIO 0 3 TSDW 0 2 TSM 0 1 TSIO 0 0 ODF 0
Bit 7: RSYNC Multiframe Skip Control (RSMS) Useful in framing format conversions from D4 to ESF. This function is not available when the receive-side elastic store is enabled. RSYNC must be set to output multiframe pulses (TR.IOCR1.5 = 1 and TR.IOCR1.4 = 0). 0 = RSYNC outputs a pulse at every multiframe 1 = RSYNC outputs a pulse at every other multiframe Bit 6: RSYNC Mode Select 2 (RSMS2) T1 Mode: RSYNC pin must be programmed in the output frame mode (TR.IOCR1.5 = 0,TR.IOCR1.4 = 0). 0 = do not pulse double-wide in signaling frames 1 = do pulse double-wide in signaling frames E1 Mode: RSYNC pin must be programmed in the output multiframe mode (TR.IOCR1.5 = 1, TR.IOCR1.4 = 0). 0 = RSYNC outputs CAS multiframe boundaries 1 = RSYNC outputs CRC4 multiframe boundaries Bit 5: RSYNC Mode Select 1(RSMS1) Selects frame or multiframe pulse when RSYNC pin is in output mode. In input mode (elastic store must be enabled), multiframe mode is only useful when receive signaling reinsertion is enabled. See the timing diagrams in Section 12. 0 = frame mode 1 = multiframe mode Bit 4: RSYNC I/O Select (RSIO) (Note: This bit must be set to 0 when TR.ESCR.0 = 0.) 0 = RSYNC is an output 1 = RSYNC is an input (only valid if elastic store enabled) Bit 3: TSYNC Double-Wide (TSDW) (Note: This bit must be set to 0 when TR.IOCR1.2 = 1 or when TR.IOCR1.1 = 0.) 0 = do not pulse double-wide in signaling frames 1 = do pulse double-wide in signaling frames Bit 2: TSYNC Mode Select (TSM) Selects frame or multiframe mode for the TSYNC pin. See the timing diagrams in Section 12. 0 = frame mode 1 = multiframe mode Bit 1: TSYNC I/O Select (TSIO) 0 = TSYNC is an input 1 = TSYNC is an output Bit 0: Output Data Format (ODF) 0 = bipolar data at TPOSO and TNEGO 1 = NRZ data at TPOSO; TNEGO = 0
198 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RCLKINV 0
TR.IOCR2 I/O Configuration Register 2 02h 6 TCLKINV 0 5 RSYNCINV 0 4 TSYNCINV 0 3 TSSYNCINV 0 2 H100EN 0 1 TSCLKM 0 0 RSCLKM 0
Bit 7: RCLKO Invert (RCLKINV) 0 = no inversion 1 = inverts signal on RCLKO output. Bit 6: TCLKT Invert (TCLKINV) 0 = no inversion 1 = inverts signal on TCLKT input. Bit 5: RSYNC Invert (RSYNCINV) 0 = no inversion 1 = invert Bit 4: TSYNC Invert (TSYNCINV) 0 = no inversion 1 = invert Bit 3: TSSYNC Invert (TSSYNCINV) 0 = no inversion 1 = invert Bit 2 : H.100 SYNC Mode (H100EN) 0 = normal operation 1 = SYNC shift Bit 1: TSYSCLK Mode Select (TSCLKM) 0 = if TSYSCLK is 1.544MHz 1 = if TSYSCLK is 2.048MHz Bit 0: RSYSCLK Mode Select (RSCLKM) 0 = if RSYSCLK is 1.544MHz 1 = if RSYSCLK is 2.048MHz
199 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.T1RCR1 T1 Receive Control Register 1 03h 6 ARC 0 5 OOF1 0 4 OOF2 0 3 SYNCC 0 2 SYNCT 0 1 SYNCE 0 0 RESYNC 0
Bit 6: Auto Resync Criteria (ARC) 0 = resync on OOF or RCL event 1 = resync on OOF only Bits 4- 5: Out-of-Frame Select Bits (OOF2, OOF1) OOF2 0 0 1 1 OOF1 0 1 0 1 Out-Of-Frame Criteria 2/4 frame bits in error 2/5 frame bits in error 2/6 frame bits in error 2/6 frame bits in error
Bit 3: Sync Criteria (SYNCC) In D4 Framing Mode: 0 = search for Ft pattern, then search for Fs pattern 1 = cross couple Ft and Fs pattern In ESF Framing Mode: 0 = search for FPS pattern only 1 = search for FPS and verify with CRC6 Bit 2: Sync Time (SYNCT) 0 = qualify 10 bits 1 = qualify 24 bits Bit 1: Sync Enable (SYNCE) 0 = auto resync enabled 1 = auto resync disabled Bit 0: Resynchronize (RESYNC) When toggled from low to high, a resynchronization of the receive-side framer is initiated. Must be cleared and set again for a subsequent resync.
200 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.T1RCR2 T1 Receive Control Register 2 04h 6 RFM 0 5 RB8ZS 0 4 RSLC96 0 3 RZSE 0 2 -- 0 1 RJC 0 0 RD4YM 0
Bit 6: Receive Frame Mode Select (RFM) 0 = D4 framing mode 1 = ESF framing mode Bit 5: Receive B8ZS Enable (RB8ZS) 0 = B8ZS disabled 1 = B8ZS enabled Bit 4: Receive SLC-96 Enable (RSLC96). Only set this bit to a 1 in D4/SLC-96 framing applications. See Section 10.19 for details. 0 = SLC-96 disabled 1 = SLC-96 enabled Bit 3: Receive FDL Zero-Destuffer Enable (RZSE). Set this bit to 0 if using the internal HDLC/BOC controller instead of the legacy support for the FDL. See Section 10.18 for details. 0 = zero destuffer disabled 1 = zero destuffer enabled Bit 2: Reserved. Set to zero for proper operation. Bit 1: Receive Japanese CRC6 Enable (RJC) 0 = use ANSI/AT&T/ITU CRC6 calculation (normal operation) 1 = use Japanese standard JT-G704 CRC6 calculation Bit 0: Receive-Side D4 Yellow Alarm Select (RD4YM) 0 = 0s in bit 2 of all channels 1 = a 1 in the S-bit position of frame 12 (J1 Yellow Alarm Mode)
201 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 TJC 0
TR.T1TCR1 T1 Transmit Control Register 1 05h 6 TFPT 0 5 TCPT 0 4 TSSE 0 3 GB7S 0 2 TFDLS 0 1 TBL 0 0 TYEL 0
Bit 7: Transmit Japanese CRC6 Enable (TJC) 0 = use ANSI/AT&T/ITU CRC6 calculation (normal operation) 1 = use Japanese standard JT-G704 CRC6 calculation Bit 6: Transmit F-Bit Pass-Through (TFPT) 0 = F bits sourced internally 1 = F bits sampled at TSERI Bit 5: Transmit CRC Pass-Through (TCPT) 0 = source CRC6 bits internally 1 = CRC6 bits sampled at TSERI during F-bit time Bit 4: Transmit Software Signaling Enable (TSSE). 0 = do not source signaling data from the TR.TSx registers regardless of the TR.SSIEx registers. The TR.SSIEx registers still define which channels are to have B7 stuffing preformed. 1 = source signaling data as enabled by the TR.SSIEx registers Bit 3: Global Bit 7 Stuffing (GB7S) 0 = allow the SSIEx registers to determine which channels containing all 0s are to be bit 7 stuffed 1 = force bit 7 stuffing in all 0-byte channels regardless of how the TR.SSIEx registers are programmed Bit 2: TFDL Register Select (TFDLS) 0 = source FDL or Fs-bits from the internal TR.TFDL register (legacy FDL support mode) 1 = source FDL or Fs-bits from the internal HDLC controller Bit 1: Transmit Blue Alarm (TBL) 0 = transmit data normally 1 = transmit an unframed all-ones code at TPOS and TNEG Bit 0: Transmit Yellow Alarm (TYEL) 0 = do not transmit yellow alarm 1 = transmit yellow alarm
202 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TB8ZS 0 TR.T1TCR2 T1 Transmit Control Register 2 06h 6 TSLC96 0 5 TZSE 0 4 FBCT2 0 3 FBCT1 0 2 TD4YM 0 1 -- 0 0 TB7ZS 0
Bit 7: Transmit B8ZS Enable (TB8ZS) 0 = B8ZS disabled 1 = B8ZS enabled Bit 6: Transmit SLC-96/Fs-Bit Insertion Enable (TSLC96). Only set this bit to a 1 in D4 framing applications. Must be set to 1 to source the Fs pattern from the TR.TFDL register. See Section 10.19 for details. 0 = SLC-96/Fs-bit insertion disabled 1 = SLC-96/Fs-bit insertion enabled Bit 5: Transmit FDL Zero-Stuffer Enable (TZSE). Set this bit to 0 if using the internal HDLC controller instead of the legacy support for the FDL. See Section 15 for details. 0 = zero stuffer disabled 1 = zero stuffer enabled Bit 4: F-Bit Corruption Type 2 (FBCT2). Setting this bit high enables the corruption of one Ft (D4 framing mode) or FPS (ESF framing mode) bit in every 128 Ft or FPS bits as long as the bit remains set. Bit 3: F-Bit Corruption Type 1 (FBCT1). A low-to-high transition of this bit causes the next three consecutive Ft (D4 framing mode) or FPS (ESF framing mode) bits to be corrupted causing the remote end to experience a loss of synchronization. Bit 2: Transmit-Side D4 Yellow Alarm Select (TD4YM) 0 = 0s in bit 2 of all channels 1 = a 1 in the S-bit position of frame 12 Bit 0: Transmit-Side Bit 7 Zero-Suppression Enable (TB7ZS) 0 = no stuffing occurs 1 = bit 7 forced to a 1 in channels with all 0s
203 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.T1CCR1 T1 Common Control Register 1 07h 6 -- 0 5 -- 0 4 TRAI-CI 0 3 TAIS-CI 0 2 TFM 0 1 PDE 0 0 TLOOP 0
Bit 4: Transmit RAI-CI Enable (TRAI-CI). Setting this bit causes the ESF RAI-CI code to be transmitted in the FDL bit position. 0 = do not transmit the ESF RAI-CI code 1 = transmit the ESF RAI-CI code Bit 3: Transmit AIS-CI Enable (TAIS-CI). Setting this bit and the TBL bit (TR.T1TCR1.1) causes the AIS-CI code to be transmitted at TPOSO and TNEGO, as defined in ANSI T1.403. 0 = do not transmit the AIS-CI code 1 = transmit the AIS-CI code (TR.T1TCR1.1 must also be set = 1) Bit 2: Transmit Frame Mode Select (TFM) 0 = D4 framing mode 1 = ESF framing mode Bit 1: Pulse Density Enforcer Enable (PDE). The framer always examines the transmit and receive data streams for violations of these, which are required by ANSI T1.403: No more than 15 consecutive 0s and at least N 1s in each and every time window of 8 x (N + 1) bits, where N = 1 through 23. Violations for the transmit and receive data streams are reported in the TR.INFO1.6 and TR.INFO1.7 bits, respectively. When this bit is set to 1, the T1/E1/J1 transceiver forces the transmitted stream to meet this requirement no matter the content of the transmitted stream. When running B8ZS, this bit should be set to 0 since B8ZS encoded data streams cannot violate the pulse density requirements. 0 = disable transmit pulse density enforcer 1 = enable transmit pulse density enforcer Bit 0: Transmit Loop-Code Enable (TLOOP). See Section 10.20 for details. 0 = transmit data normally 1 = replace normal transmitted data with repeating code as defined in registers TR.TCD1 and TR.TCD2
Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0
TR.SSIE1 (T1 Mode) Software Signaling Insertion Enable 1 08h 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Software Signaling Insertion Enable for Channels 1 to 8 (CH1 to CH8). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel
204 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH7 0 TR.SSIE1 (E1 Mode) Software Signaling Insertion Enable 1 08h 6 CH6 0 5 CH5 0 4 CH4 0 3 CH3 0 2 CH2 0 1 CH1 0 0 UCAW 0
Bits 1 - 7: Software Signaling-Insertion Enable for Channels 1 to 7 (CH1 to CH7). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel Bit 0: Upper CAS Align/Alarm Word (UCAW). Selects the upper CAS align/alarm pattern (0000) to be sourced from the upper 4 bits of the TS1 register. 0 = do not source the upper CAS align/alarm pattern from the TR.TS1 register 1 = source the upper CAS align/alarm pattern from the TR.TS1 register Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.SSIE2 (T1 Mode) Software Signaling-Insertion Enable 2 09h 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Software Signaling Insertion Enable for Channels 9 to 16 (CH9 to CH16). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel
Register Name: Register Description: Register Address: Bit # Name Default 7 CH15 0
TR.SSIE2 (E1 Mode) Software Signaling Insertion Enable 2 09h 6 CH14 0 5 CH13 0 4 CH12 0 3 CH11 0 2 CH10 0 1 CH9 0 0 CH8 0
Bits 0 - 7: Software Signaling Insertion Enable for Channels 8 to 15 (CH8 to CH15). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel
205 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.SSIE3 (T1 Mode) Software Signaling-Insertion Enable 3 0Ah 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Software Signaling Insertion Enable for Channels 17 to 24 (CH17 to CH24). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel Register Name: Register Description: Register Address: Bit # Name Default 7 CH22 0 TR.SSIE3 (E1 Mode) Software Signaling Insertion Enable 3 0Ah 6 CH21 0 5 CH20 0 4 CH19 0 3 CH18 0 2 CH17 0 1 CH16 0 0 LCAW 0
Bits 1 - 7: Software Signaling Insertion Enable for LCAW and Channels 16 to 22 (CH16 to CH22). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel Bit 0: Lower CAS Align/Alarm Word (LCAW). Selects the lower CAS align/alarm bits (xyxx) to be sourced from the lower 4 bits of the TS1 register. 0 = do not source the lower CAS align/alarm bits from the TR.TS1 register 1 = source the lower CAS alarm align/bits from the TR.TS1 register
Register Name: Register Description: Register Address: Bit # Name Default 7 CH30 0
TR.SSIE4 Software Signaling Insertion Enable 4 0Bh 6 CH29 0 5 CH28 0 4 CH27 0 3 CH26 0 2 CH25 0 1 CH24 0 0 CH23 0
Bits 0 - 7: Software Signaling Insertion Enable for Channels 22 to 30 (CH23 to CH30). These bits determine which channels are to have signaling inserted from the transmit signaling registers. 0 = do not source signaling data from the TR.TSx registers for this channel 1 = source signaling data from the TR.TSx registers for this channel
206 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0 TR.T1RDMR1 T1 Receive Digital-Milliwatt Enable Register 1 0Ch 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Receive Digital-Milliwatt Enable for Channels 1 to 8 (CH1 to CH8) 0 = do not affect the receive data associated with this channel 1 = replace the receive data associated with this channel with digital-milliwatt code Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.T1RDMR2 T1 Receive Digital-Milliwatt Enable Register 2 0Dh 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Receive Digital-Milliwatt Enable for Channels 9 to 16 (CH9 to CH16) 0 = do not affect the receive data associated with this channel 1 = replace the receive data associated with this channel with digital-milliwatt code Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.T1RDMR3 T1 Receive Digital-Milliwatt Enable Register 3 0Eh 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Receive Digital-Milliwatt Enable for Channels 17 to 24 (CH17 to CH24) 0 = do not affect the receive data associated with this channel 1 = replace the receive data associated with this channel with digital-milliwatt code
207 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 ID7 1 TR.IDR Device Identification Register 0Fh 6 ID6 0 5 ID5 1 4 ID4 1 3 ID3 X 2 ID2 X 1 ID1 X 0 ID0 X
Bits 4 - 7: Device ID (ID4 to ID7). The upper four bits of TR.IDR are used to display the transceiver ID. Bits 0 - 3: Chip Revision Bits (ID0 to ID3). The lower four bits of TR.IDR are used to display the die revision of the chip. IDO is the LSB of a decimal code that represents the chip revision.
Register Name: Register Description: Register Address: Bit # Name Default 7 RPDV 0
TR.INFO1 Information Register 1 10h 6 TPDV 0 5 COFA 0 4 8ZD 0 3 16ZD 0 2 SEFE 0 1 B8ZS 0 0 FBE 0
Bit 7: Receive Pulse-Density Violation Event (RPDV). Set when the receive data stream does not meet the ANSI T1.403 requirements for pulse density. Bit 6: Transmit Pulse-Density Violation Event (TPDV). Set when the transmit data stream does not meet the ANSI T1.403 requirements for pulse density. Bit 5: Change-of-Frame Alignment Event (COFA). Set when the last resync resulted in a change-of-frame or multiframe alignment. Bit 4: Eight Zero-Detect Event (8ZD). Set when a string of at least eight consecutive 0s (regardless of the length of the string) have been received at RPOSI and RNEGI. Bit 3: Sixteen Zero-Detect Event (16ZD). Set when a string of at least 16 consecutive 0s (regardless of the length of the string) have been received at RPOSI and RNEGI. Bit 2: Severely Errored Framing Event (SEFE). Set when two out of six framing bits (Ft or FPS) are received in error. Bit 1: B8ZS Codeword Detect Event (B8ZS). Set when a B8ZS codeword is detected at RPOS and RNEG independent of whether the B8ZS mode is selected or not by TR.T1TCR2.7. Useful for automatically setting the line coding. Bit 0: Frame Bit-Error Event (FBE). Set when an Ft (D4) or FPS (ESF) framing bit is received in error.
208 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 BSYNC 0 TR.INFO2 Information Register 2 11h 6 BD 0 5 TCLE 0 4 TOCD 0 3 RL3 0 2 RL2 0 1 RL1 0 0 RL0 0
Bit 7: BERT Real-Time Synchronization Status (BSYNC). Real-time status of the synchronizer (this bit is not latched). This bit is set when the incoming pattern matches for 32 consecutive bit positions. It is cleared when six or more bits out of 64 are received in error. Refer to BSYNC in the BERT status register, TR.SR9, for an interruptgenerating version of this signal. Bit 6: BOC Detected (BD). A real-time bit that is set high when the BOC detector is presently seeing a valid sequence and set low when no BOC is currently being detected. Bit 5: Transmit Current-Limit Exceeded (TCLE). A real-time bit that is set when the 50mA (RMS) current limiter is activated, whether the current limiter is enabled or not. Bit 4: Transmit Open-Circuit Detect (TOCD). A real-time bit that is set when the device detects that the TTIP and TRING outputs are open-circuited. Bits 0 - 3: Receive Level Bits (RL0 to RL3). Real-time bits RL3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 RL2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 RL1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 RL0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Receive Level (dB) Greater than -2.5 -2.5 to -5.0 -5.0 to -7.5 -7.5 to -10.0 -10.0 to -12.5 -12.5 to -15.0 -15.0 to -17.5 -17.5 to -20.0 -20.0 to -22.5 -22.5 to -25.0 -25.0 to -27.5 -27.5 to -30.0 -30.0 to -32.5 -32.5 to -35.0 -35.0 to -37.5 Less than -37.5
NOTE: RL0 through RL3 only indicate the signal range as specified by the EGL bit in TR.LIC1. Example; if EGL = 1 and in T1 mode, RL0 through RL3 will only indicate a signal range of >-2.5dB to -15dB even if the signal is < -15dB.
209 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.INFO3 Information Register 3 12h 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 CRCRC 0 1 FASRC 0 0 CASRC 0
Bit 2: CRC Resync Criteria Met Event (CRCRC). Set when 915/1000 codewords are received in error. Bit 1: FAS Resync Criteria Met Event (FASRC). Set when three consecutive FAS words are received in error. Note: During a CRC resync the FAS synchronizer is brought online to verify the FAS alignment. If during this process an FAS emulator exists, the FAS synchronizer may temporarily align to the emulator. The FASRC will go active indicating a search for a valid FAS has been activated. Bit 0: CAS Resync Criteria Met Event (CASRC). Set when two consecutive CAS MF alignment words are received in error.
Register Name: Register Description: Register Address: Bit # Name Default 7 SR8 0
TR.IIR1 Interrupt Information Register 1 14h 6 SR7 0 5 SR6 0 4 SR5 0 3 SR4 0 2 SR3 0 1 SR2 0 0 SR1 0
Bits 0 - 7: Status Register 1 - 8 When set to 1, these bits indicate that an enabled interrupt is active in the associated T1/E1/J1 status register. Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.IIR2 Interrupt Information Register 2 15h 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 SR9 0
Bits 0: Status Register 9 When set to 1, this bit indicates that an enabled interrupt is active in the associated T1/E1/J1 status register.
210 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 ILUT 0 TR.SR1 Status Register 1 16h 6 TIMER 0 5 RSCOS 0 4 JALT 0 3 LRCL 0 2 TCLE 0 1 TOCD 0 0 LOLITC 0
Bit 7: Input Level Under Threshold (ILUT). This bit is set whenever the input level at RTIP and RRING falls below the threshold set by the value in TR.CCR4.4 through TR.CCR4.7. The level must remain below the programmed threshold for approximately 50ms for this bit to be set. This is a double interrupt bit (Section 9.7). Bit 6: Timer Event (TIMER). Follows the error-counter update interval as determined by the ECUS bit in the errorcounter configuration register (TR.ERCNT). T1: set on increments of 1 second or 42ms based on RCLKO E1: set on increments of 1 second or 62.5ms based on RCLKO Bit 5: Receive Signaling Change-of-State Event (RSCOS). Set when any channel selected by the receive signaling change-of-state interrupt-enable registers (TR.RSCSE1 through TR.RSCSE4) changes signaling state. Bit 4: Jitter Attenuator Limit Trip Event (JALT). Set when the jitter attenuator FIFO reaches to within 4 bits of its useful limit. This bit is cleared when read. Useful for debugging jitter attenuation operation. Bit 3: Line Interface Receive Carrier-Loss Condition (LRCL). Set when the carrier signal is lost. This is a double interrupt bit (Section 9.7). Bit 2: Transmit Current-Limit Exceeded Condition (TCLE). Set when the 50mA (RMS) current limiter is activated, whether the current limiter is enabled or not. This is a double interrupt bit (Section 9.7). Bit 1: Transmit Open-Circuit Detect Condition (TOCD). Set when the device detects that the TTIP and TRING outputs are open-circuited. This is a double interrupt bit (Section 9.7). Bit 0: Loss of Line-Interface Transmit-Clock Condition (LOLITC). Set when TDCLKI has not transitioned for one channel time. This is a double interrupt bit (Section 9.7).
211 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 ILUT 0 TR.IMR1 Interrupt Mask Register 1 17h 6 TIMER 0 5 RSCOS 0 4 JALT 0 3 LRCL 0 2 TCLE 0 1 TOCD 0 0 LOLITC 0
Bit 7: Input Level Under Threshold (ILUT) 0 = interrupt masked 1 = interrupt enabled Bit 6: Timer Event (TIMER) 0 = interrupt masked 1 = interrupt enabled Bit 5: Receive Signaling Change-of-State Event (RSCOS) 0 = interrupt masked 1 = interrupt enabled Bit 4: Jitter Attenuator Limit Trip Event (JALT) 0 = interrupt masked 1 = interrupt enabled Bit 3: Line Interface Receive Carrier-Loss Condition (LRCL) 0 = interrupt masked 1 = interrupt enabled--generates interrupts on rising and falling edges Bit 2: Transmit Current-Limit Exceeded Condition (TCLE) 0 = interrupt masked 1 = interrupt enabled--generates interrupts on rising and falling edges Bit 1: Transmit Open-Circuit Detect Condition (TOCD) 0 = interrupt masked 1 = interrupt enabled--generates interrupts on rising and falling edges Bit 0: Loss-of-Transmit Clock Condition (LOLITC) 0 = interrupt masked 1 = interrupt enabled--generates interrupts on rising and falling edges
212 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RYELC 0 TR.SR2 Status Register 2 18h 6 RUA1C 0 5 FRCLC 0 4 RLOSC 0 3 RYEL 0 2 RUA1 0 1 FRCL 0 0 RLOS 0
Bit 7: Receive Yellow Alarm Clear Event (RYELC) (T1 Only). Set when the receive Yellow Alarm condition is no longer detected. Bit 6: Receive Unframed All-Ones Clear Event (RUA1C). Set when the unframed all 1s condition is no longer detected. Bit 5: Framer Receive Carrier-Loss Clear Event (FRCLC). Set when the carrier loss condition at RPOSI and RNEGI is no longer detected. Bit 4: Receive Loss-of-Sync Clear Event (RLOSC). Set when the framer achieves synchronization; remains set until read. Bit 3: Receive Yellow Alarm Condition (RYEL) (T1 Only). Set when a Yellow Alarm is received at RPOSI and RNEGI. Bit 2: Receive Unframed All-Ones (T1 Blue Alarm, E1 AIS) Condition (RUA1). Set when an unframed all 1s code is received at RPOSI and RNEGI. Bit 1: Framer Receive Carrier-Loss Condition (FRCL). Set when 255 (or 2048 if TR.E1RCR2.0 = 1) E1 mode or 192 T1 mode consecutive 0s have been detected at RPOSI and RNEGI. Bit 0: Receive Loss-of-Sync Condition (RLOS). Set when the transceiver is not synchronized to the received data stream.
213 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RYELC 0
TR.IMR2 Interrupt Mask Register 2 19h 6 RUA1C 0 5 FRCLC 0 4 RLOSC 0 3 RYEL 0 2 RUA1 0 1 FRCL 0 0 RLOS 0
Bit 7: Receive Yellow Alarm Clear Event (RYELC) 0 = interrupt masked 1 = interrupt enabled Bit 6: Receive Unframed All-Ones Condition Clear Event (RUA1C) 0 = interrupt masked 1 = interrupt enabled Bit 5: Framer Receive Carrier Loss Condition Clear (FRCLC) 0 = interrupt masked 1 = interrupt enabled Bit 4: Receive Loss-of-Sync Clear Event (RLOSC) 0 = interrupt masked 1 = interrupt enabled Bit 3: Receive Yellow Alarm Condition (RYEL) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only Bit 2: Receive Unframed All-Ones (Blue Alarm) Condition (RUA1) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only Bit 1: Framer Receive Carrier Loss Condition (FRCL) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only Bit 0: Receive Loss-of-Sync Condition (RLOS) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only
214 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 LSPARE 0 TR.SR3 Status Register 3 1Ah 6 LDN 0 5 LUP 0 4 LOTC 0 3 LORC 0 2 V52LNK 0 1 RDMA 0 0 RRA 0
Bit 7: Spare Code Detected Condition (LSPARE) (T1 Only). Set when the spare code as defined in the TR.RSCD1/2 registers is being received. See Section 10.20 for details. This is a double interrupt bit. See Section 9.7. Bit 6: Loop-Down Code Detected Condition (LDN) (T1 Only). Set when the loop down code as defined in the TR.RDNCD1/2 register is being received. See Section 10.20 for details. This is a double interrupt bit. See Section 9.7. Bit 5: Loop-Up Code Detected Condition (LUP) (T1 Only). Set when the loop-up code as defined in the TR.RUPCD1/2 register is being received. See Section 10.20 for details. This is a double interrupt bit. See Section 9.7. Bit 4: Loss-of-Transmit Clock Condition (LOTC). Set when the TCLKT pin has not transitioned for one channel time. Forces the LOTC pin high if enabled by TR.CCR1.0. This is a double interrupt bit. See Section 9.7. Bit 3: Loss-of-Receive Clock Condition (LORC). Set when the RDCLKI pin has not transitioned for one channel time. This is a double interrupt bit. See Section 9.7. Bit 2: V5.2 Link Detected Condition (V52LNK) (E1 Only). Set on detection of a V5.2 link identification signal (G.965). This is a double interrupt bit. See Section 9.7. Bit 1: Receive Distant MF Alarm Condition (RDMA) (E1 Only). Set when bit 6 of time slot 16 in frame 0 has been set for two consecutive multiframes. This alarm is not disabled in the CCS signaling mode. This is a double interrupt bit. See Section 9.7. Bit 0: Receive Remote Alarm Condition (RRA) (E1 Only). Set when a remote alarm is received at RPOSI and RNEGI. This is a double interrupt bit. See Section 9.7.
215 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 LSPARE 0 TR.IMR3 Interrupt Mask Register 3 1Bh 6 LDN 0 5 LUP 0 4 LOTC 0 3 LORC 0 2 V52LNK 0 1 RDMA 0 0 RRA 0
Bit 7: Spare Code Detected Condition (LSPARE) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 6: Loop-Down Code-Detected Condition (LDN) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 5: Loop-Up Code-Detected Condition (LUP) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 4: Loss-of-Transmit Clock Condition (LOTC) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 3: Loss-of-Receive Clock Condition (LORC) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 2: V5.2 Link Detected Condition (V52LNK) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 1: Receive Distant MF Alarm Condition (RDMA) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 0: Receive Remote Alarm Condition (RRA) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges
216 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 RAIS-CI 0
TR.SR4 Status Register 4 1Ch 6 RSAO 0 5 RSAZ 0 4 TMF 0 3 TAF 0 2 RMF 0 1 RCMF 0 0 RAF 0
Bit 7: Receive AIS-CI Event (RAIS-CI) (T1 Only). Set when the receiver detects the AIS-CI pattern as defined in ANSI T1.403. Bit 6: Receive Signaling All-Ones Event (RSAO) (E1 Only). Set when the contents of time slot 16 contains fewer than three 0s over 16 consecutive frames. This alarm is not disabled in the CCS signaling mode. Bit 5: Receive Signaling All-Zeros Event (RSAZ) (E1 Only). Set when over a full MF, time slot 16 contains all 0s. Bit 4: Transmit Multiframe Event (TMF) E1 Mode: Set every 2ms (regardless if CRC4 is enabled) on transmit multiframe boundaries. Used to alert the host that signaling data needs to be updated. T1 Mode: Set every 1.5ms on D4 MF boundaries or every 3ms on ESF MF boundaries. Bit 3: Transmit Align Frame Event (TAF) (E1 Only). Set every 250s at the beginning of align frames. Used to alert the host that the TR.TAF and TR.TNAF registers need to be updated. Bit 2: Receive Multiframe Event (RMF) E1 Mode: Set every 2ms (regardless if CAS signaling is enabled or not) on receive multiframe boundaries. Used to alert the host that signaling data is available. T1 Mode: Set every 1.5ms on D4 MF boundaries or every 3ms on ESF MF boundaries. Bit 1: Receive CRC4 Multiframe Event (RCMF) (E1 Only). Set on CRC4 multiframe boundaries; continues to set every 2ms on an arbitrary boundary if CRC4 is disabled. Bit 0: Receive Align Frame Event (RAF) (E1 Only). Set every 250s at the beginning of align frames. Used to alert the host that Si and Sa bits are available in the TR.RAF and TR.RNAF registers.
217 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RAIS-CI 0 TR.IMR4 Interrupt Mask Register 4 1Dh 6 RSAO 0 5 RSAZ 0 4 TMF 0 3 TAF 0 2 RMF 0 1 RCMF 0 0 RAF 0
Bit 7: Receive AIS-CI Event (RAIS-CI) 0 = interrupt masked 1 = interrupt enabled Bit 6: Receive Signaling All-Ones Event (RSAO) 0 = interrupt masked 1 = interrupt enabled Bit 5: Receive Signaling All-Zeros Event (RSAZ) 0 = interrupt masked 1 = interrupt enabled Bit 4: Transmit Multiframe Event (TMF) 0 = interrupt masked 1 = interrupt enabled Bit 3: Transmit Align Frame Event (TAF) 0 = interrupt masked 1 = interrupt enabled Bit 2: Receive Multiframe Event (RMF) 0 = interrupt masked 1 = interrupt enabled Bit 1: Receive CRC4 Multiframe Event (RCMF) 0 = interrupt masked 1 = interrupt enabled Bit 0: Receive Align Frame Event (RAF) 0 = interrupt masked 1 = interrupt enabled
218 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.SR5 Status Register 5 1Eh 6 -- 0 5 TESF 0 4 TESEM 0 3 TSLIP 0 2 RESF 0 1 RESEM 0 0 RSLIP 0
Bit 5: Transmit Elastic Store Full Event (TESF). Set when the transmit elastic store buffer fills and a frame is deleted. Bit 4: Transmit Elastic Store Empty Event (TESEM). Set when the transmit elastic store buffer empties and a frame is repeated. Bit 3: Transmit Elastic Store Slip-Occurrence Event (TSLIP). Set when the transmit elastic store has either repeated or deleted a frame. Bit 2: Receive Elastic Store Full Event (RESF). Set when the receive elastic store buffer fills and a frame is deleted. Bit 1: Receive Elastic Store Empty Event (RESEM). Set when the receive elastic store buffer empties and a frame is repeated. Bit 0: Receive Elastic Store Slip-Occurrence Event (RSLIP). Set when the receive elastic store has either repeated or deleted a frame.
219 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.IMR5 Interrupt Mask Register 5 1Fh 6 -- 0 5 TESF 0 4 TESEM 0 3 TSLIP 0 2 RESF 0 1 RESEM 0 0 RSLIP 0
Bit 5: Transmit Elastic Store Full Event (TESF) 0 = interrupt masked 1 = interrupt enabled Bit 4: Transmit Elastic Store Empty Event (TESEM) 0 = interrupt masked 1 = interrupt enabled Bit 3: Transmit Elastic Store Slip-Occurrence Event (TSLIP) 0 = interrupt masked 1 = interrupt enabled Bit 2: Receive Elastic Store Full Event (RESF) 0 = interrupt masked 1 = interrupt enabled Bit 1: Receive Elastic Store Empty Event (RESEM) 0 = interrupt masked 1 = interrupt enabled Bit 0: Receive Elastic Store Slip-Occurrence Event (RSLIP) 0 = interrupt masked 1 = interrupt enabled
220 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.SR6, TR.SR7 HDLC #1 Status Register 6 HDLC #2 Status Register 7 20h, 22h 6 TMEND 0 5 RPE 0 4 RPS 0 3 RHWM 0 2 RNE 0 1 TLWM 0 0 TNF 0
Bit 6: Transmit Message-End Event (TMEND). Set when the transmit HDLC controller has finished sending a message. This is a latched bit and is cleared when read. Bit 5: Receive Packet-End Event (RPE). Set when the HDLC controller detects either the finish of a valid message (i.e., CRC check complete) or when the controller has experienced a message fault such as a CRC checking error, or an overrun condition, or an abort has been seen. This is a latched bit and is cleared when read. Bit 4: Receive Packet-Start Event (RPS). Set when the HDLC controller detects an opening byte. This is a latched bit and is cleared when read. Bit 3: Receive FIFO Above High-Watermark Condition (RHWM). Set when the receive 128-byte FIFO fills beyond the high watermark as defined by the receive high-watermark register (TR.RHWMR). Bit 2: Receive FIFO Not Empty Condition (RNE). Set when the receive 128-byte FIFO has at least 1 byte available for a read. Bit 1: Transmit FIFO Below Low-Watermark Condition (TLWM). Set when the transmit 128-byte FIFO empties beyond the low watermark as defined by the transmit low-watermark register (TR.TLWMR). Bit 0: Transmit FIFO Not Full Condition (TNF). Set when the transmit 128-byte FIFO has at least 1 byte available.
221 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.IMR6, TR.IMR7 HDLC # 1 Interrupt Mask Register 6 HDLC # 2 Interrupt Mask Register 7 21h, 23h 6 TMEND 0 5 RPE 0 4 RPS 0 3 RHWM 0 2 RNE 0 1 TLWM 0 0 TNF 0
Bit 6: Transmit Message-End Event (TMEND) 0 = interrupt masked 1 = interrupt enabled Bit 5: Receive Packet-End Event (RPE) 0 = interrupt masked 1 = interrupt enabled Bit 4: Receive Packet-Start Event (RPS) 0 = interrupt masked 1 = interrupt enabled Bit 3: Receive FIFO Above High-Watermark Condition (RHWM) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only Bit 2: Receive FIFO Not Empty Condition (RNE) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only Bit 1: Transmit FIFO Below Low-Watermark Condition (TLWM) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only Bit 0: Transmit FIFO Not Full Condition (TNF) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising edge only
222 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0
TR.INFO5, TR.INFO6 HDLC #1 Information Register HDLC #2 Information Register 2Eh, 2Fh 6 -- 0 5 TEMPTY 0 4 TFULL 0 3 REMPTY 0 2 PS2 0 1 PS1 0 0 PS0 0
Bit 5: Transmit FIFO Empty (TEMPTY). A real-time bit that is set high when the FIFO is empty. Bit 4: Transmit FIFO Full (TFULL). A real-time bit that is set high when the FIFO is full. Bit 3: Receive FIFO Empty (REMPTY). A real-time bit that is set high when the receive FIFO is empty. Bits 0 - 2: Receive Packet Status (PS0 to PS2). These are real-time bits indicating the status as of the last read of the receive FIFO. PS2 0 0 0 0 1 PS1 0 0 1 1 0 PS0 0 1 0 1 0 In Progress Packet OK: Packet ended with correct CRC codeword CRC Error: A closing flag was detected, preceded by a corrupt CRC codeword Abort: Packet ended because an abort signal was detected (seven or more 1s in a row). Overrun: HDLC controller terminated reception of packet because receive FIFO is full. TR.INFO4 HDLC Event Information Register #4 2Dh 6 -- 0 5 -- 0 4 -- 0 3 H2UDR 0 2 H2OBT 0 1 H1UDR 0 0 H1OBT 0 Packet Status
Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0
Bit 3: HDLC #2 Transmit FIFO Underrun Event (H2UDR). Set when the transmit FIFO empties out without having seen the TMEND bit set. An abort is automatically sent. This bit is latched and is cleared when read. Bit 2: HDLC #2 Opening Byte Event (H2OBT). Set when the next byte available in the receive FIFO is the first byte of a message. Bit 1: HDLC #1 Transmit FIFO Underrun Event (H1UDR). Set when the transmit FIFO empties out without having seen the TMEND bit set. An abort is automatically sent. This bit is latched and is cleared when read. Bit 0: HDLC #1 Opening Byte Event (H1OBT). Set when the next byte available in the receive FIFO is the first byte of a message.
223 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.SR8 Status Register 8 24h 6 -- 0 5 BOCC 0 4 RFDLAD 0 3 RFDLF 0 2 TFDLE 0 1 RMTCH 0 0 RBOC 0
Bit 5: BOC Clear Event (BOCC). Set when 30 FDL bits occur without an abort sequence. Bit 4: RFDL Abort Detect Event (RFDLAD). Set when eight consecutive 1s are received on the FDL. Bit 3: RFDL Register Full Event (RFDLF). Set when the receive FDL buffer (TR.RFDL) fills to capacity. Bit 2: TFDL Register Empty Event (TFDLE). Set when the transmit FDL buffer (TR.TFDL) empties. Bit 1: Receive FDL Match Event (RMTCH). Set whenever the contents of the TR.RFDL register matches TR.RFDLM1 or TR.RFDLM2. Bit 0: Receive BOC Detector Change-of-State Event (RBOC). Set whenever the BOC detector sees a change of state to a valid BOC. The setting of this bit prompts the user to read the TR.RFDL register. Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 6 -- 0 TR.IMR8 Interrupt Mask Register 8 25h 5 BOCC 0 4 RFDLAD 0 3 RFDLF 0 2 TFDLE 0 1 RMTCH 0 0 RBOC 0
Bit 5: BOC Clear Event (BOCC) 0 = interrupt masked 1 = interrupt enabled Bit 4: RFDL Abort Detect Event (RFDLAD) 0 = interrupt masked 1 = interrupt enabled Bit 3: RFDL Register Full Event (RFDLF) 0 = interrupt masked 1 = interrupt enabled Bit 2: TFDL Register Empty Event (TFDLE) 0 = interrupt masked 1 = interrupt enabled Bit 1: Receive FDL Match Event (RMTCH) 0 = interrupt masked 1 = interrupt enabled Bit 0: Receive BOC Detector Change-of-State Event (RBOC) 0 = interrupt masked 1 = interrupt enabled
224 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.SR9 Status Register 9 26h 6 BBED 0 5 BBCO 0 4 BEC0 0 3 BRA1 0 2 BRA0 0 1 BRLOS 0 0 BSYNC 0
Bit 6: BERT Bit-Error Detected (BED) Event (BBED). A latched bit that is set when a bit error is detected. The receive BERT must be in synchronization for it to detect bit errors. Cleared when read. Bit 5: BERT Bit-Counter Overflow Event (BBCO). A latched bit that is set when the 32-bit BERT bit counter (BBC) overflows. Cleared when read and is not set again until another overflow occurs. Bit 4: BERT Error-Counter Overflow (BECO) Event (BECO). A latched bit that is set when the 24-bit BERT error counter (BEC) overflows. Cleared when read and is not set again until another overflow occurs. Bit 3: BERT Receive All-Ones Condition (BRA1). A latched bit that is set when 32 consecutive 1s are received. Allowed to be cleared once a 0 is received. This is a double interrupt bit (Section 9.7). Bit 2: BERT Receive All-Zeros Condition (BRA0). A latched bit that is set when 32 consecutive 0s are received. Allowed to be cleared once a 1 is received. This is a double interrupt bit (Section 9.7). Bit 1: BERT Receive Loss-of-Synchronization Condition (BRLOS). A latched bit that is set whenever the receive BERT begins searching for a pattern. Once synchronization is achieved, this bit remains set until read. This is a double interrupt bit (Section 9.7). Bit 0: BERT in Synchronization Condition (BSYNC). Set when the incoming pattern matches for 32 consecutive bit positions. Refer to BSYNC in the TR.INFO2 register for a real-time version of this bit. This is a double interrupt bit (Section 9.7).
225 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.IMR9 Interrupt Mask Register 9 27h 6 BBED 0 5 BBCO 0 4 BEC0 0 3 BRA1 0 2 BRA0 0 1 BRLOS 0 0 BSYNC 0
Bit 6: Bit-Error Detected Event (BBED) 0 = interrupt masked 1 = interrupt enabled Bit 5: BERT Bit-Counter Overflow Event (BBCO) 0 = interrupt masked 1 = interrupt enabled Bit 4: BERT Error-Counter Overflow Event (BECO) 0 = interrupt masked 1 = interrupt enabled Bit 3: Receive All-Ones Condition (BRA1) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 2: Receive All-Zeros Condition (BRA0) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 1: Receive Loss-of-Synchronization Condition (BRLOS) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges Bit 0: BERT in Synchronization Condition (BSYNC) 0 = interrupt masked 1 = interrupt enabled--interrupts on rising and falling edges
226 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RSAOICS 0 TR.PCPR Per-Channel Pointer Register 28h 6 RSRCS 0 5 RFCS 0 4 BRCS 0 3 THSCS 0 2 PEICS 0 1 TFCS 0 0 BTCS 0
Bit 7: Receive Signaling All-Ones Insertion Channel Select (RSAOICS) Bit 6: Receive Signaling Reinsertion Channel Select (RSRCS) Bit 5: Receive Fractional Channel Select (RFCS) Bit 4: Bert Receive Channel Select (BRCS) Bit 3: Transmit Hardware Signaling Channel Select (THSCS) Bit 2: Payload Error Insert Channel Select (PEICS) Bit 1: Transmit Fractional Channel Select (TFCS) Bit 0: Bert Transmit Channel Select (BTCS) See Section 10.2 for a general overview of per-channel operation. See Section 10.10 for more information on perchannel idle code generation. See Section 10.6 for more information on per-channel loopback operation.
227 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- CH8 TR.PCDR1 Per-Channel Data Register 1 29h 6 -- CH7 5 -- CH6 4 -- CH5 3 -- CH4 2 -- CH3 1 -- CH2 0 -- CH1
Register Name: Register Description: Register Address: Bit # Name Default 7 -- CH16
TR.PCDR2 Per-Channel Data Register 2 2Ah 6 -- CH15 5 -- CH14 4 -- CH13 3 -- CH12 2 -- CH11 1 -- CH10 0 -- CH9
Register Name: Register Description: Register Address: Bit # Name Default 7 -- CH24
TR.PCDR3 Per-Channel Data Register 3 2Bh 6 -- CH23 5 -- CH22 4 -- CH21 3 -- CH20 2 -- CH19 1 -- CH18 0 -- CH17
Register Name: Register Description: Register Address: Bit # Name Default 7 -- CH32
TR.PCDR4 Per-Channel Data Register 4 2Ch 6 -- CH31 5 -- CH30 4 -- CH29 3 -- CH28 2 -- CH27 1 -- CH26 0 -- CH25
See Section 10.2 for a general overview of per-channel operation. See Section 10.10 for more information on perchannel idle code generation. See Section 10.6 for more information on per-channel loopback operation.
228 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CSC5 0 TR.INFO7 Information Register 7 (Real-Time, Non-Latched Register) 30h 6 CSC4 0 5 CSC3 0 4 CSC2 0 3 CSC0 0 2 FASSA 0 1 CASSA 0 0 CRC4SA 0
Bits 3 - 7: CRC4 Sync Counter Bits (CSC0, CSC2 to CSC4). The CRC4 sync counter increments each time the 8ms CRC4 multiframe search times out. The counter is cleared when the framer has successfully obtained synchronization at the CRC4 level. The counter can also be cleared by disabling the CRC4 mode (TR.E1RCR1.3 = 0). This counter is useful for determining the amount of time the framer has been searching for synchronization at the CRC4 level. ITU G.706 suggests that if synchronization at the CRC4 level cannot be obtained within 400ms, then the search should be abandoned and proper action taken. The CRC4 sync counter rolls over. CSC0 is the LSB of the 6-bit counter. (Note: The bit next to LSB is not accessible. CSC1 is omitted to allow resolution to >400ms using 5 bits.) These are read-only, non-latched, real-time bits. It is not necessary to precede the read of these bits with a write. Bit 2: FAS Sync Active (FASSA). Set while the synchronizer is searching for alignment at the FAS level. This is a read-only, non-latched, real-time bit. It is not necessary to precede the read of this bit with a write. Bit 1: CAS MF Sync Active (CASSA). Set while the synchronizer is searching for the CAS MF alignment word. This is a read-only, non-latched, real-time bit. It is not necessary to precede the read of this bit with a write. Bit 0: CRC4 MF Sync Active (CRC4SA). Set while the synchronizer is searching for the CRC4 MF alignment word. This is a read-only, non-latched, real-time bit. It is not necessary to precede the read of this bit with a write. Register Name: Register Description: Register Address: Bit # Name Default 7 RHR 0 TR.H1RC, TR.H2RC HDLC #1 Receive Control HDLC #2 Receive Control 31h, 32h 6 RHMS 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 RSFD 0
Bit 7: Receive HDLC Reset (RHR). Resets the receive HDLC controller and flushes the receive FIFO. Must be cleared and set again for a subsequent reset. 0 = normal operation 1 = reset receive HDLC controller and flush the receive FIFO Bit 6: Receive HDLC Mapping Select (RHMS) 0 = receive HDLC assigned to channels 1 = receive HDLC assigned to FDL (T1 mode), Sa bits (E1 mode) Bits 1 - 5: Unused, must be set to 0 or proper operation Bit 0: Receive SS7 Fill-In Signal Unit Delete (RSFD) 0 = normal operation; all FISUs are stored in the receive FIFO and reported to the host. 1 = When a consecutive FISU having the same BSN the previous FISU is detected, it is deleted without host intervention.
229 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RSERC 0 TR.E1RCR1 E1 Receive Control Register 1 33h 6 RSIGM 0 5 RHDB3 0 4 RG802 0 3 RCRC4 0 2 FRC 0 1 SYNCE 0 0 RESYNC 0
Bit 7: RSERO Control (RSERC) 0 = allow RSERO to output data as received under all conditions 1 = force RSERO to 1 under loss-of-frame alignment conditions Bit 6: Receive Signaling Mode Select (RSIGM) 0 = CAS signaling mode 1 = CCS signaling mode Bit 5: Receive HDB3 Enable (RHDB3) 0 = HDB3 disabled 1 = HDB3 enabled Bit 4: Receive G.802 Enable (RG802). See Section 10.10 for details. 0 = do not force RCHBLK high during bit 1 of time slot 26 1 = force RCHBLK high during bit 1 of time slot 26 Bit 3: Receive CRC4 Enable (RCRC4) 0 = CRC4 disabled 1 = CRC4 enabled Bit 2: Frame Resync Criteria (FRC) 0 = resync if FAS received in error three consecutive times 1 = resync if FAS or bit 2 of non-FAS is received in error three consecutive times Bit 1: Sync Enable (SYNCE) 0 = auto resync enabled 1 = auto resync disabled Bit 0: Resync (RESYNC). When toggled from low to high, a resync is initiated. Must be cleared and set again for a subsequent resync. Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.E1RCR2 E1 Receive Control Register 2 34h 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 -- 0 0 RCLA 0
Bit 0: Receive Carrier-Loss (RCL) Alternate Criteria (RCLA). Defines the criteria for a receive carrier-loss condition for both the framer and LIU. 0 = RCL declared upon 255 consecutive 0s (125s) 1 = RCL declared upon 2048 consecutive 0s (1ms)
230 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TFPT 0 TR.E1TCR1 E1 Transmit Control Register 1 35h 6 T16S 0 5 TUA1 0 4 TSiS 0 3 TSA1 0 2 THDB3 0 1 TG802 0 0 TCRC4 0
Bit 7: Transmit Time Slot 0 Pass-Through (TFPT) 0 = FAS bits/Sa bits/remote alarm sourced internally from the TR.TAF and TR.TNAF registers 1 = FAS bits/Sa bits/remote alarm sourced from TSERI Bit 6: Transmit Time Slot 16 Data Select (T16S) 0 = time slot 16 determined by the TR.SSIEx registers and the THSCS function in the TR.PCPR register 1 = source time slot 16 from TR.TS1 to TR.TS16 registers Bit 5: Transmit Unframed All Ones (TUA1) 0 = transmit data normally 1 = transmit an unframed all-ones code at TPOSO and TNEGO Bit 4: Transmit International Bit Select (TSiS) 0 = sample Si bits at TSERI pin 1 = source Si bits from TR.TAF and TR.TNAF registers (in this mode, TR.E1TCR1.7 must be set to 0) Bit 3: Transmit Signaling All Ones (TSA1) 0 = normal operation 1 = force time slot 16 in every frame to all ones Bit 2: Transmit HDB3 Enable (THDB3) 0 = HDB3 disabled 1 = HDB3 enabled Bit 1: Transmit G.802 Enable (TG802). See Section 10.10 for details. 0 = do not force TCHBLK high during bit 1 of time slot 26 1 = force TCHBLK high during bit 1 of time slot 26 Bit 0: Transmit CRC4 Enable (TCRC4) 0 = CRC4 disabled 1 = CRC4 enabled
231 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0
TR.E1TCR2 E1 Transmit Control Register 2 36h 6 0 5 0 4 0 3 0 2 AEBE 0 1 AAIS 0 0 ARA 0
Bit 2: Automatic E-Bit Enable (AEBE) 0 = E-bits not automatically set in the transmit direction 1 = E-bits automatically set in the transmit direction Bit 1: Automatic AIS Generation (AAIS) 0 = disabled 1 = enabled Bit 0: Automatic Remote Alarm Generation (ARA) 0 = disabled 1 = enabled Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.BOCC BOC Control Register 37h 6 -- 0 5 -- 0 4 RBOCE 0 3 RBR 0 2 RBF1 0 1 RBF0 0 0 SBOC 0
Bit 4: Receive BOC Enable (RBOCE). Enables the receive BOC function. The TR.RFDL register reports the received BOC code and two information bits when this bit is set. 0 = receive BOC function disabled 1 = receive BOC function enabled; the TR.RFDL register reports BOC messages and information Bit 3: Receive BOC Reset (RBR). A 0-to-1 transition resets the BOC circuitry. Must be cleared and set again for a subsequent reset. Bits 1 - 2: Receive BOC Filter Bits (RBF0, RBF1). The BOC filter sets the number of consecutive patterns that must be received without error prior to an indication of a valid message. RBF1 0 0 1 1 RBF0 0 1 0 1 Consecutive BOC Codes for Valid Sequence Identification None 3 5 7
Bit 0: Send BOC (SBOC). Set = 1 to transmit the BOC code placed in bits 0 to 5 of the TR.TFDL register.
232 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: (MSB) CH8 CH16 CH24 TR.RSINFO1, TR.RSINFO2, TR.RSINFO3, TR.RSINFO4 Receive Signaling Change-of-State Information 38h, 39h, 3Ah, 3Bh (LSB) CH1 CH9 CH17 CH25
CH7 CH15 CH23
CH6 CH14 CH22 CH30
CH5 CH13 CH21 CH29
CH4 CH12 CH20 CH28
CH3 CH11 CH19 CH27
CH2 CH10 CH18 CH26
RSINFO1 RSINFO2 RSINFO3 RSINFO4
When a channel's signaling data changes state, the respective bit in registers TR.RSINFO1-4 is set. An interrupt is generated if the channel was also enabled as an interrupt source by setting the appropriate bit in TR.RSCSE1-4. The bit remains set until read. Register Name: Register Description: Register Address: (MSB) CH8 CH16 CH24 TR.RSCSE1, TR.RSCSE2, TR.RSCSE3, TR.RSCSE4 Receive Signaling Change-of-State Interrupt Enable 3Ch, 3Dh, 3Eh, 3Fh (LSB) CH1 CH9 CH17 CH25
CH7 CH15 CH23
CH6 CH14 CH22 CH30
CH5 CH13 CH21 CH29
CH4 CH12 CH20 CH28
CH3 CH11 CH19 CH27
CH2 CH10 CH18 CH26
RSCSE1 RSCSE2 RSCSE3 RSCSE4
Setting any of the CH1-CH30 bits in the TR.RSCSE1- TR.RSCSE4 registers causes an interrupt when that channel's signaling data changes state.
233 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 GRSRE 0 TR.SIGCR Signaling Control Register 40h 6 -- 0 5 -- 0 4 RFE 0 3 RFF 0 2 RCCS 0 1 TCCS 0 0 FRSAO 0
Bit 7: Global Receive Signaling Reinsertion Enable (GRSRE). This bit allows the user to reinsert all signaling channels without programming all channels through the per-channel function. 0 = do not reinsert all signaling 1 = reinsert all signaling Bit 4: Receive Freeze Enable (RFE). See Section 10.9.2.3 for details. 0 = no freezing of receive signaling data occurs 1 = allow freezing of receive signaling data at RSIG (and RSERO if receive signaling reinsertion is enabled) Bit 3: Receive Force Freeze (RFF). Freezes receive-side signaling at RSIG (and RSERO if receive signaling reinsertion is enabled); overrides receive freeze enable (RFE). See Section 10.9.2.3 for details. 0 = do not force a freeze event 1 = force a freeze event Bit 2: Receive Time Slot Control for CAS Signaling (RCCS). Controls the order that signaling is placed into the receive signaling registers. This bit should be set = 0 in T1 mode. 0 = signaling data is CAS format 1 = signaling data is CCS format Bit 1: Transmit Time Slot Control for CAS Signaling (TCCS). Controls the order that signaling is transmitted from the transmit signaling registers. This bit should be set = 0 in T1 mode. 0 = signaling data is CAS format 1 = signaling data is CCS format Bit 0: Force Receive Signaling All Ones (FRSAO). In T1 mode, this bit forces all signaling data at the RSIG and RSERO pin to all ones. This bit has no effect in E1 mode. 0 = normal signaling data at RSIG and RSERO 1 = force signaling data at RSIG and RSERO to all ones
234 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.ERCNT Error-Counter Configuration Register 41h 6 MECU 0 5 ECUS 0 4 EAMS 0 3 VCRFS 0 2 FSBE 0 1 MOSCRF 0 0 LCVCRF 0
Bit 6: Manual Error-Counter Update (MECU). When enabled by TR.ERCNT.4, the changing of this bit from a 0 to a 1 allows the next clock cycle to load the error-counter registers with the latest counts and reset the counters. The user must wait a minimum of 1.5 RCLKO clock periods before reading the error count registers to allow for proper update. Bit 5: Error-Counter Update Select (ECUS) T1 Mode: 0 = update error counters once a second 1 = update error counters every 42ms (333 frames) E1 Mode: 0 = update error counters once a second 1 = update error counters every 62.5ms (500 frames) Bit 4: Error-Accumulation Mode Select (EAMS) 0 = TR.ERCNT.5 determines accumulation time 1 = TR.ERCNT.6 determines accumulation time Bit 3: E1 Line-Code Violation Count Register Function Select (VCRFS) 0 = count bipolar violations (BPVs) 1 = count code violations (CVs) Bit 2: PCVCR Fs-Bit Error-Report Enable (FSBE) 0 = do not report bit errors in Fs-bit position; only Ft-bit position 1 = report bit errors in Fs-bit position as well as Ft-bit position Bit 1: Multiframe Out-of-Sync Count Register Function Select (MOSCRF) 0 = count errors in the framing bit position 1 = count the number of multiframes out-of-sync Bit 0: T1 Line-Code Violation Count Register Function Select (LCVCRF) 0 = do not count excessive 0s 1 = count excessive 0s Register Name: Register Description: Register Address: Bit # Name Default 7 LCVC15 0 TR.LCVCR1 Line-Code Violation Count Register 1 42h 6 LCVC14 0 5 LCVC13 0 4 LCVC12 0 3 LCVC11 0 2 LCVC10 0 1 LCVC9 0 0 LCCV8 0
Bits 0 - 7: Line-Code Violation Counter Bits 8 to 15 (LCVC8 to LCVC15). LCV15 is the MSB of the 16-bit code violation count.
235 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 LCVC7 0 TR.LCVCR2 Line-Code Violation Count Register 2 43h 6 LCVC6 0 5 LCVC5 0 4 LCVC4 0 3 LCVC3 0 2 LCVC2 0 1 LCVC1 0 0 LCVC0 0
Bits 0 - 7: Line-Code Violation Counter Bits 0 to 7 (LCVC0 to LCVC7). LCV0 is the LSB of the 16-bit code violation count. Register Name: Register Description: Register Address: Bit # Name Default 7 PCVC15 0 TR.PCVCR1 Path Code Violation Count Register 1 44h 6 PCVC14 0 5 PCVC13 0 4 PCVC12 0 3 PCVC11 0 2 PCVC10 0 1 PCVC9 0 0 PCVC8 0
Bits 0 - 7: Path Code Violation Counter Bits 8 to 15 (PCVC8 to PCVC15). PCVC15 is the MSB of the 16-bit path code violation count. Register Name: Register Description: Register Address: Bit # Name Default 7 PCVC7 0 TR.PCVCR2 Path Code Violation Count Register 2 45h 6 PCVC6 0 5 PCVC5 0 4 PCVC4 0 3 PCVC3 0 2 PCVC2 0 1 PCVC1 0 0 PCVC0 0
Bits 0 - 7: Path Code Violation Counter Bits 0 to 7 (PCVC0 to PCVC7). PCVC0 is the LSB of the 16-bit path code violation count. Register Name: Register Description: Register Address: Bit # Name Default 7 FOS15 0 TR.FOSCR1 Frames Out-of-Sync Count Register 1 46h 6 FOS14 0 5 FOS13 0 4 FOS12 0 3 FOS11 0 2 FOS10 0 1 FOS9 0 0 FOS8 0
Bits 0 - 7: Frames Out-of-Sync Counter Bits 8 to 15 (FOS8 to FOS15). FOS15 is the MSB of the 16-bit frames out-of-sync count.
236 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 FOS7 0 TR.FOSCR2 Frames Out-of-Sync Count Register 2 47h 6 FOS6 0 5 FOS5 0 4 FOS4 0 3 FOS3 0 2 FOS2 0 1 FOS1 0 0 FOS0 0
Bits 0 - 7: Frames Out-of-Sync Counter Bits 0 to 7 (FOS0 to FOS7). FOS0 is the LSB of the 16-bit frames outof-sync count. Register Name: Register Description: Register Address: Bit # Name Default 7 EB15 0 TR.EBCR1 E-Bit Count Register 1 48h 6 EB14 0 5 EB13 0 4 EB12 0 3 EB11 0 2 EB10 0 1 EB9 0 0 EB8 0
Bits 0 - 7: E-Bit Counter Bits 8 to 15 (EB8 to EB15). EB15 is the MSB of the 16-bit E-bit count. Register Name: Register Description: Register Address: Bit # Name Default 7 EB7 0 TR.EBCR2 E-Bit Count Register 2 49h 6 EB6 0 5 EB5 0 4 EB4 0 3 EB3 0 2 EB2 0 1 EB1 0 0 EB0 0
Bits 0 - 7: E-Bit Counter Bits 0 to 7 (EB0 to EB7). EB0 is the LSB of the 16-bit E-bit count.
237 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.LBCR Loopback Control Register 4Ah 6 -- 0 5 -- 0 4 LIUC 0 3 LLB 0 2 RLB 0 1 PLB 0 0 FLB 0
Bit 4: Line Interface Unit Mux Control (LIUC). This is a software version of the LIUC pin. When the LIUC pin is connected high, the LIUC bit has control. When the LIUC pin is connected low, the framer and LIU are separated and the LIUC bit has no effect. 0 = LIU internally connected to framer. 1 = LIU disconnected from framer. Use TPOSI/TNEGI/TDCLKI/RPOSI/RNEGI/RDCLKI pins LIUC Pin 0 0 1 1 LIUC Bit 0 1 0 1 Condition LIU and framer separated LIU and framer separated LIU and framer connected LIU and framer separated
Bit 3: Local Loopback (LLB). When this bit is set to 1, data continues to be transmitted as normal through the transmit side of the transceiver. Data being received at RTIP and RRING are replaced with the data being transmitted. Data in this loopback passes through the jitter attenuator. See Figure 6-3 for more details. Bit 2: Remote Loopback (RLB). When this bit is set to 1, data input by the RPOSI and RNEGI pins is transmitted back to the TPOSO and TNEGO pins. Data continues to pass through the receive-side framer of the transceiver as it would normally. Data from the transmit-side formatter is ignored. See Figure 6-2 for more details. Bit 1: Payload Loopback (PLB). When set to 1, payload loopback is enabled and the following occurs: 1) Data is transmitted from the TPOSO and TNEGO pins synchronous with RCLKO instead of TCLKT. 2) All the receive side signals continue to operate normally. 3) Data at the TSERI, TDATA, and TSIG pins is ignored. T1 Mode: Normally, this loopback is only enabled when ESF framing is being performed but can also be enabled in D4 framing applications. The transceiver loops the 192 bits of payload data (with BPVs corrected) from the receive section back to the transmit section. The FPS framing pattern, CRC6 calculation, and the FDL bits are not looped back; they are reinserted by the transceiver. E1 Mode: The transceiver loops the 248 bits of payload data (with BPVs corrected) from the receive section back to the transmit section. The transmit section modifies the payload as if it was input at TSERI. The FAS word; Si, Sa, and E bits; and CRC4 are not looped back; they are reinserted by the transceiver. Bit 0: Framer Loopback (FLB). When this bit is set to 1, the transceiver loops data from the transmit side back to the receive side. When FLB is enabled, the following occurs: 1) T1 Mode: An unframed all-ones code is transmitted at TPOSO and TNEGO. E1 Mode: Normal data is transmitted at TPOSO and TNEGO. 2) Data at RPOSI and RNEGI is ignored. 3) All receive-side signals take on timing synchronous with TCLKT instead of RDCLKI. Please note that it is not acceptable to have RCLKO connected to TCLKT during this loopback because this causes an unstable condition.
238 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0 TR.PCLR1 Per-Channel Loopback Enable Register 1 4Bh 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Per-Channel Loopback Enable for Channels 1 to 8 (CH1 to CH8) 0 = loopback disabled 1 = enable loopback; source data from the corresponding receive channel Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.PCLR2 Per-Channel Loopback Enable Register 2 4Ch 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Per-Channel Loopback Enable for Channels 9 to 16 (CH9 to CH16) 0 = loopback disabled 1 = enable loopback; source data from the corresponding receive channel Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.PCLR3 Per-Channel Loopback Enable Register 3 4Dh 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Per-Channel Loopback Enable for Channels 17 to 24 (CH17 to CH24) 0 = loopback disabled 1 = enable loopback; source data from the corresponding receive channel Register Name: Register Description: Register Address: Bit # Name Default 7 CH32 0 TR.PCLR4 Per-Channel Loopback Enable Register 4 4Eh 6 CH31 0 5 CH30 0 4 CH29 0 3 CH28 0 2 CH27 0 1 CH26 0 0 CH25 0
Bits 0 - 7: Per-Channel Loopback Enable for Channels 25 to 32 (CH25 to CH32) 0 = loopback disabled 1 = enable loopback; source data from the corresponding receive channel
239 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TESALGN 0 TR.ESCR Elastic Store Control Register 4Fh 6 TESR 0 5 TESMDM 0 4 TESE 0 3 RESALGN 0 2 RESR 0 1 RESMDM 0 0 RESE 0
Bit 7: Transmit Elastic Store Align (TESALGN). Setting this bit from a 0 to a 1 forces the transmit elastic store's write/read pointers to a minimum separation of half a frame. No action is taken if the pointer separation is already greater or equal to half a frame. If pointer separation is less than half a frame, the command is executed and the data is disrupted. It should be toggled after TSYSCLK has been applied and is stable. It must be cleared and set again for a subsequent align. See Section 10.12.3 for details. Bit 6: Transmit Elastic Store Reset (TESR). Setting this bit from a 0 to a 1 forces the read and write pointers into opposite frames, maximizing the delay through the transmit elastic store. Transmit data is lost during the reset. It should be toggled after TSYSCLK has been applied and is stable. See Section 10.12.3 for details. Do not leave this bit set HIGH. Bit 5: Transmit Elastic Store Minimum-Delay Mode (TESMDM). See Section 10.12.4 for details. 0 = elastic stores operate at full two-frame depth 1 = elastic stores operate at 32-bit depth Bit 4: Transmit Elastic Store Enable (TESE) 0 = elastic store is bypassed 1 = elastic store is enabled Bit 3: Receive Elastic Store Align (RESALGN). Setting this bit from a 0 to a 1 forces the receive elastic store's write/read pointers to a minimum separation of half a frame. No action is taken if the pointer separation is already greater or equal to half a frame. If pointer separation is less than half a frame, the command is executed and the data is disrupted. It should be toggled after RSYSCLK has been applied and is stable. Must be cleared and set again for a subsequent align. See Section 10.12.3 for details. Bit 2: Receive Elastic Store Reset (RESR). Setting this bit from a 0 to a 1 forces the read and write pointers into opposite frames, maximizing the delay through the receive elastic store. It should be toggled after RSYSCLK has been applied and is stable. See Section 10.12.3 for details. Do not leave this bit set HIGH. Bit 1: Receive Elastic Store Minimum-Delay Mode (RESMDM). See Section 10.12.4 for details. 0 = elastic stores operate at full two-frame depth 1 = elastic stores operate at 32-bit depth Bit 0: Receive Elastic Store Enable (RESE) 0 = elastic store is bypassed 1 = elastic store is enabled
240 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: (MSB) 0 CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A CH26-A CH28-A CH30-A TR.TS1 to TR.TS16 Transmit Signaling Registers (E1 Mode, CAS Format) 50h to 5Fh (LSB) X CH1-D CH3-D CH5-D CH7-D CH9-D CH11-D CH13-D CH15-D CH17-D CH19-D CH21-D CH23-D CH25-D CH27-D CH29-D
0 CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B CH26-B CH28-B CH30-B
0 CH2-C CH4-C CH6-C CH8-C CH10-C CH12-C CH14-C CH16-C CH18-C CH20-C CH22-C CH24-C CH26-C CH28-C CH30-C
0 CH2-D CH4-D CH6-D CH8-D CH10-D CH12-D CH14-D CH16-D CH18-D CH20-D CH22-D CH24-D CH26-D CH28-D CH30-D
X CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A CH25-A CH27-A CH29-A
Y CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B CH25-B CH27-B CH29-B
X CH1-C CH3-C CH5-C CH7-C CH9-C CH11-C CH13-C CH15-C CH17-C CH19-C CH21-C CH23-C CH25-C CH27-C CH29-C
TS1 TS2 TS3 TS4 TS5 TS6 TS7 TS8 TS9 TS10 TS11 TS12 TS13 TS14 TS15 TS16
Register Name: Register Description: Register Address: (MSB) 1 9 17 25 33 41 49 57 65 73 81 89 97 105 113 121
TR.TS1 to TR.TS16 Transmit Signaling Registers (E1 Mode, CCS Format) 50h to 5Fh (LSB) 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128
2 10 18 26 34 42 50 58 66 74 82 90 98 106 114 122
3 11 19 27 35 43 51 59 67 75 83 91 99 107 115 123
4 12 20 28 36 44 52 60 68 76 84 92 100 108 116 124
5 13 21 29 37 45 53 61 69 77 85 93 101 109 117 125
6 14 22 30 38 46 54 62 70 78 86 94 102 110 118 126
7 15 23 31 39 47 55 63 71 79 87 95 103 111 119 127
TS1 TS2 TS3 TS4 TS5 TS6 TS7 TS8 TS9 TS10 TS11 TS12 TS13 TS14 TS15 TS16
241 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: (MSB) CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A
TR.TS1 to TR.TS12 Transmit Signaling Registers (T1 Mode, ESF Format) 50h to 5Bh (LSB) CH1-D CH3-D CH5-D CH7-D CH9-D CH11-D CH13-D CH15-D CH17-D CH19-D CH21-D CH23-D
CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B
CH2-C CH4-C CH6-C CH8-C CH10-C CH12-C CH14-C CH16-C CH18-C CH20-C CH22-C CH24-C
CH2-D CH4-D CH6-D CH8-D CH10-D CH12-D CH14-D CH16-D CH18-D CH20-D CH22-D CH24-D
CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A
CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B
CH1-C CH3-C CH5-C CH7-C CH9-C CH11-C CH13-C CH15-C CH17-C CH19-C CH21-C CH23-C
TS1 TS2 TS3 TS4 TS5 TS6 TS7 TS8 TS9 TS10 TS11 TS12
Register Name: Register Description: Register Address: (MSB) CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A
TR.TS1 to TR.TS12 Transmit Signaling Registers (T1 Mode, D4 Format) 50h to 5Bh (LSB) CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B
CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B
CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A
CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B
CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A
CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B
CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A
TS1 TS2 TS3 TS4 TS5 TS6 TS7 TS8 TS9 TS10 TS11 TS12
Note: In D4 format, TR.TS1- TR.TS12 contain signaling data for two frames. Bold type indicates data for second frame.
242 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: (MSB) CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A TR.RS1 to TR.RS12 Receive Signaling Registers (T1 Mode, ESF Format) 60h to 6Bh (LSB) CH1-D CH3-D CH5-D CH7-D CH9-D CH11-D CH13-D CH15-D CH17-D CH19-D CH21-D CH23-D
CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B
CH2-C CH4-C CH6-C CH8-C CH10-C CH12-C CH14-C CH16-C CH18-C CH20-C CH22-C CH24-C
CH2-D CH4-D CH6-D CH8-D CH10-D CH12-D CH14-D CH16-D CH18-D CH20-D CH22-D CH24-D
CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A
CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B
CH1-C CH3-C CH5-C CH7-C CH9-C CH11-C CH13-C CH15-C CH17-C CH19-C CH21-C CH23-C
RS1 RS2 RS3 RS4 RS5 RS6 RS7 RS8 RS9 RS10 RS11 RS12
Register Name: Register Description: Register Address: (MSB) CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A
TR.RS1 to TR.RS12 Receive Signaling Registers (T1 Mode, D4 Format) 60h to 6Bh (LSB) CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B
CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B
CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A
CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B
CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A
CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B
CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A
RS1 RS2 RS3 RS4 RS5 RS6 RS7 RS8 RS9 RS10 RS11 RS12
Note: In D4 format, TR.TS1- TR.TS12 contain signaling data for two frames. Bold type indicates data for second frame.
243 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: (MSB) 0 CH2-A CH4-A CH6-A CH8-A CH10-A CH12-A CH14-A CH16-A CH18-A CH20-A CH22-A CH24-A CH26-A CH28-A CH30-A TR.RS1 to TR.RS16 Receive Signaling Registers (E1 Mode, CAS Format) 60h to 6Fh (LSB) X CH1-D CH3-D CH5-D CH7-D CH9-D CH11-D CH13-D CH15-D CH17-D CH19-D CH21-D CH23-D CH25-D CH27-D CH29-D
0 CH2-B CH4-B CH6-B CH8-B CH10-B CH12-B CH14-B CH16-B CH18-B CH20-B CH22-B CH24-B CH26-B CH28-B CH30-B
0 CH2-C CH4-C CH6-C CH8-C CH10-C CH12-C CH14-C CH16-C CH18-C CH20-C CH22-C CH24-C CH26-C CH28-C CH30-C
0 CH2-D CH4-D CH6-D CH8-D CH10-D CH12-D CH14-D CH16-D CH18-D CH20-D CH22-D CH24-D CH26-D CH28-D CH30-D
X CH1-A CH3-A CH5-A CH7-A CH9-A CH11-A CH13-A CH15-A CH17-A CH19-A CH21-A CH23-A CH25-A CH27-A CH29-A
Y CH1-B CH3-B CH5-B CH7-B CH9-B CH11-B CH13-B CH15-B CH17-B CH19-B CH21-B CH23-B CH25-B CH27-B CH29-B
X CH1-C CH3-C CH5-C CH7-C CH9-C CH11-C CH13-C CH15-C CH17-C CH19-C CH21-C CH23-C CH25-C CH27-C CH29-C
RS1 RS2 RS3 RS4 RS5 RS6 RS7 RS8 RS9 RS10 RS11 RS12 RS13 RS14 RS15 RS16
Register Name: Register Description: Register Address: (MSB) 1 9 17 25 33 41 49 57 65 73 81 89 97 105 113 121
TR.RS1 to TR.RS16 Receive Signaling Registers (E1 Mode, CCS Format) 60h to 6Fh (LSB) 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128
2 10 18 26 34 42 50 58 66 74 82 90 98 106 114 122
3 11 19 27 35 43 51 59 67 75 83 91 99 107 115 123
4 12 20 28 36 44 52 60 68 76 84 92 100 108 116 124
5 13 21 29 37 45 53 61 69 77 85 93 101 109 117 125
6 14 22 30 38 46 54 62 70 78 86 94 102 110 118 126
7 15 23 31 39 47 55 63 71 79 87 95 103 111 119 127
RS1 RS2 RS3 RS4 RS5 RS6 RS7 RS8 RS9 RS10 RS11 RS12 RS13 RS14 RS15 RS16
244 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 MCLKS 0
TR.CCR1 Common Control Register 1 70h 6 CRC4R 0 5 SIE 0 4 ODM 0 3 DICAI 0 2 TCSS1 0 1 TCSS0 0 0 RLOSF 0
Bit 7: MCLK Source (MCLKS). Selects the source of MCLK 0 = MCLK is source from the MCLK pin 1 = MCLK is source from the TSYSCLK pin Bit 6: CRC-4 Recalculate (CRC4R) 0 = transmit CRC-4 generation and insertion operates in normal mode 1 = transmit CRC-4 generation operates according to G.706 intermediate path recalculation method Bit 5: Signaling Integration Enable (SIE) 0 = signaling changes of state reported on any change in selected channels 1 = signaling must be stable for three multiframes in order for a change of state to be reported Bit 4: Output Data Mode (ODM) 0 = pulses at TPOSO and TNEGO are one full TCLKO period wide 1 = pulses at TPOSO and TNEGO are one-half TCLKO period wide Bit 3: Disable Idle Code Auto Increment (DICAI). Selects/deselects the auto-increment feature for the transmit and receive idle code array address register. See Section 10.10. 0 = addresses in TR.IAAR register automatically increment on every read/write operation to the TR.PCICR register 1 = addresses in TR.IAAR register do not automatically increment Bit 2: Transmit Clock Source Select Bit 0 (TCSS1) TCSS1 0 0 1 1 TCSS0 0 1 0 1 Transmit Clock Source The TCLKT pin is always the source of transmit clock. Switch to the clock present at RCLKO when the signal at the TCLKT pin fails to transition after 1 channel time. Use the scaled signal present at MCLK as the transmit clock. The TCLKT pin is ignored. Use the signal present at RCLKO as the transmit clock. The TCLKT pin is ignored.
Bit 1: Transmit Clock Source Select Bit 0 (TCSS0) Bit 0: Function of the RLOS/LOTC Output (RLOSF) 0 = receive loss of sync (RLOS) 1 = loss-of-transmit clock (LOTC)
245 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 TR.CCR2 Common Control Register 2 71h 6 0 5 0 4 0 3 0 2 BPCS1 0 1 BPCS0 0 0 BPEN 0
Bits 1 - 2: Backplane Clock Selects (BPCS0, BPCS1) BPCS1 0 0 1 1 BPCS0 0 1 0 1 BPCLK Frequency (MHz) 16.384 8.192 4.096 2.048
Bit 0: Backplane Clock Enable (BPEN) 0 = disable BPCLK pin (pin held at logic 0) 1 = enable BPCLK pin Register Name: Register Description: Register Address: Bit # Name Default 7 TMSS 0 TR.CCR3 Common Control Register 3 72h 5 0 4 0 3 TDATFMT 0 2 TGPCKEN 0 1 RDATFMT 0 0 RGPCKEN 0
6 INTDIS 0
Bit 7: Transmit Multiframe Sync Source (TMSS). Should be set = 0 only when transmit hardware signaling is enabled. 0 = elastic store is source of multiframe sync 1 = framer or TSYNC pin is source of multiframe sync Bit 6: Interrupt Disable (INTDIS). This bit is convenient for disabling interrupts without altering the various interrupt mask register settings. 0 = interrupts are enabled according to the various mask register settings 1 = interrupts are disabled regardless of the mask register settings Bit 3: Transmit Channel-Data Format (TDATFMT) 0 = 64kbps (data contained in all 8 bits) 1 = 56kbps (data contained in seven out of the 8 bits) Bit 2: Transmit Gapped-Clock Enable (TGPCKEN) 0 = TCHCLK functions normally 1 = enable gapped bit-clock output on TCHCLK Bit 1: Receive Channel-Data Format (RDATFMT) 0 = 64kbps (data contained in all 8 bits) 1 = 56kbps (data contained in seven out of the 8 bits) Bit 0: Receive Gapped-Clock Enable (RGPCKEN) 0 = RCHCLK functions normally 1 = enable gapped bit-clock output on RCHCLK
246 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RLT3 0 TR.CCR4 Common Control Register 4 73h 6 RLT2 0 5 RLT1 0 4 RLT0 0 3 0 2 0 1 0 0 0
Bits 4 - 7: Receive Level Threshold Bits (RLT0 to RLT3) RLT3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 RLT2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 RLT1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 RLT0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Receive Level (dB) Greater than -2.5 -2.5 -5.0 -7.5 -10.0 -12.5 -15.0 -17.5 -20.0 -22.5 -25.0 -27.5 -30.0 -32.5 -35.0 Less than -37.5
Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0
TR.TDS0SEL Transmit Channel Monitor Select 74h 6 -- 0 5 -- 0 4 TCM4 0 3 TCM3 0 2 TCM2 0 1 TCM1 0 0 TCM0 0
Bits 0 - 4: Transmit Channel Monitor Bits (TCM0 to TCM4). TCM0 is the LSB of a 5-bit channel select that determines which transmit channel data appear in the TR.TDS0M register.
247 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 B1 0 TR.TDS0M Transmit DS0 Monitor Register 75h 6 B2 0 5 B3 0 4 B4 0 3 B5 0 2 B6 0 1 B7 0 0 B8 0
Bits 0 - 7: Transmit DS0 Channel Bits (B1 to B8). Transmit channel data that has been selected by the transmit channel monitor select register. B8 is the LSB of the DS0 channel (last bit to be transmitted). Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.RDS0SEL Receive Channel Monitor Select 76h 6 -- 0 5 -- 0 4 RCM4 0 3 RCM3 0 2 RCM2 0 1 RCM1 0 0 RCM0 0
Bits 0 - 4: Receive Channel Monitor Bits (RCM0 to RCM4). RCM0 is the LSB of a 5-bit channel select that determines which receive DS0 channel data appear in the TR.RDS0M register.
Register Name: Register Description: Register Address: Bit # Name Default 7 B1 0
TR.RDS0M Receive DS0 Monitor Register 77h 6 B2 0 5 B3 0 4 B4 0 3 B5 0 2 B6 0 1 B7 0 0 B8 0
Bits 0 - 7: Receive DS0 Channel Bits (B1 to B8). Receive channel data that has been selected by the receive channel monitor select register. B8 is the LSB of the DS0 channel (last bit to be received).
248 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 L2 0 TR.LIC1 Line Interface Control 1 78h 6 L1 0 5 L0 0 4 EGL 0 3 JAS 0 2 JABDS 0 1 DJA 0 0 TPD 0
Bits 5 - 7: Line Build-Out Select (L0 to L2). When using the internal termination, the user needs only to select 000 for 75W operation or 001 for 120W operation below. This selects the proper voltage levels for 75W or 120W operation. Using TT0 and TT1 of the TR.LICR4 register, the user can then select the proper internal source termination. Line build-outs 100 and 101 are for backwards compatibility with older products only. E1 Mode L2 L1 L0 Application N (1) 0 0 0 1:2 75W normal 0 0 1 1:2 120W normal * 1 0 0 1:2 75W with high return loss * 1 0 1 1:2 120W with high return loss *TT0 and TT1 of LIC4 register must be set to 0 in this configuration. T1 Mode L2 0 0 0 0 1 1 1 1 L1 0 0 1 1 0 0 1 1 L0 0 1 0 1 0 1 0 1 Application DSX-1 (0ft to 133ft) / 0dB CSU DSX-1 (133ft to 266ft) DSX-1 (266ft to 399ft) DSX-1 (399ft to 533ft) DSX-1 (533ft to 655ft) -7.5dB CSU -15dB CSU -22.5dB CSU N (1) 1:2 1:2 1:2 1:2 1:2 1:2 1:2 1:2 Return Loss NM NM 21dB 21dB Rt (1) () 0 0 6.2 11.6
Return Loss NM NM NM NM NM NM NM NM
Rt (1) () 0 0 0 0 0 0 0 0
Bit 4: Receive Equalizer Gain Limit (EGL). This bit controls the sensitivity of the receive equalizer. T1 Mode 0 = -36dB (long haul) 1 = -15dB (limited long haul) E1 Mode 0 = -12dB (short haul) 1 = -43dB (long haul)
Bit 3: Jitter Attenuator Select (JAS) 0 = place the jitter attenuator on the receive side 1 = place the jitter attenuator on the transmit side Bit 2: Jitter Attenuator Buffer Depth Select (JABDS) 0 = 128 bits 1 = 32 bits (use for delay-sensitive applications) Bit 1: Disable Jitter Attenuator (DJA) 0 = jitter attenuator enabled 1 = jitter attenuator disabled Bit 0: Transmit Power-Down (TPD) 0 = powers down the transmitter and tri-states the TTIP and TRING pins 1 = normal transmitter operation
249 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 0 TR.TLBC Transmit Line Build-Out Control 7Dh 6 AGCE 0 5 GC5 0 4 GC4 0 3 GC3 0 2 GC2 0 1 GC1 0 0 GC0 0
Bit 6: Automatic Gain Control Enable (AGCE). 0 = use Transmit AGC, TR.TLBC bits 0-5 are "don't care" 1 = do not use Transmit AGC, TR.TLBC bits 0-5 set nominal level Bits 0-5: Gain Control Bits (GC0-GC5). The GC0 through GC5 bits control the gain setting for the nonautomatic gain mode. Use the tables below for setting the recommended values. The LB (line build-out) column refers to the value in the L0-L2 bits in TR.LIC1 (Line Interface Control 1) register. NETWORK MODE LB 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 4 5 0 1 GC5 1 0 0 1 1 1 0 1 0 0 0 0 1 1 0 1 1 1 1 1 0 0 GC4 0 1 1 0 0 0 1 1 1 1 1 1 0 0 0 1 0 0 0 0 1 1 GC3 0 1 1 0 0 0 0 1 1 0 0 1 0 0 1 1 0 0 1 1 1 1 GC2 1 0 0 0 1 1 0 1 1 1 1 0 0 0 1 1 0 0 0 0 0 0 GC1 1 1 1 0 1 1 1 1 1 0 0 1 1 0 0 1 0 0 1 0 1 1 GC0 0 1 0 0 1 1 1 1 0 1 1 0 0 0 0 1 1 1 0 0 0 0
T1, Impedance Match Off
T1, Impedance Match On
E1, Impedance Match Off E1, Impedance Match On
250 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 ETS 0 TR.LIC2 Line Interface Control 2 79h 6 LIRST 0 5 IBPV 0 4 TUA1 0 3 JAMUX 0 2 -- 0 1 SCLD 0 0 CLDS 0
Bit 7: E1/T1 Select (ETS) 0 = T1 mode selected 1 = E1 mode selected Bit 6: Line Interface Reset (LIRST). Setting this bit from a 0 to a 1 initiates an internal reset that resets the clock recovery state machine and recenters the jitter attenuator. Normally this bit is only toggled on power-up. Must be cleared and set again for a subsequent reset. Bit 5: Insert BPV (IBPV). A 0-to-1 transition on this bit causes a single BPV to be inserted into the transmit data stream. Once this bit has been toggled from a 0 to a 1, the device waits for the next occurrence of three consecutive 1s to insert the BPV. This bit must be cleared and set again for a subsequent error to be inserted. Bit 4: Transmit Unframed All Ones (TUA1). The polarity of this bit is set such that the device transmits an all-ones pattern on power-up or device reset. This bit must be set to a 1 to allow the device to transmit data. The transmission of this data pattern is always timed off of the JACLK. 0 = transmit all ones at TTIP and TRING 1 = transmit data normally Bit 3: Jitter Attenuator Mux (JAMUX). Controls the source for JACLK. 0 = JACLK sourced from MCLK (2.048MHz or 1.544MHz at MCLK) 1 = JACLK sourced from internal PLL (2.048MHz at MCLK) Bit 1: Short-Circuit Limit Disable (ETS = 1) (SCLD). Controls the 50mA (RMS) current limiter. 0 = enable 50mA current limiter 1 = disable 50mA current limiter Bit 0: Custom Line Driver Select (CLDS). Setting this bit to a 1 redefines the operation of the transmit line driver. When this bit is set to a 1 and TR.LIC1.5 = TR.LIC1.6 = TR.LIC1.7 = 0, the device generates a square wave at the TTIP and TRING outputs instead of a normal waveform. When this bit is set to a 1 and TR.LIC1.5 = TR.LIC1.6 = TR.LIC1.7 0, the device forces TTIP and TRING outputs to become open-drain drivers instead of their normal push-pull operation. This bit should be set to 0 for normal operation of the device.
251 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.LIC3 Line Interface Control 3 7Ah 6 TCES 0 5 RCES 0 4 MM1 0 3 MM0 0 2 RSCLKE 0 1 TSCLKE 0 0 TAOZ 0
Bit 6: Transmit-Clock Edge Select (TCES). Selects which TDCLKI edge to sample TPOSI and TNEGI. 0 = sample TPOSI and TNEGI on falling edge of TDCLKI 1 = sample TPOSI and TNEGI on rising edge of TDCLKI Bit 5: Receive-Clock Edge Select (RCES). Selects which RDCLKO edge to update RPOSO and RNEGO. 0 = update RPOSO and RNEGO on rising edge of RDCLKO 1 = update RPOSO and RNEGO on falling edge of RDCLKO Bits 3 - 4: Monitor Mode (MM0 to MM1) MM1 0 0 1 1 MM0 0 1 0 1 Internal Linear Gain Boost (dB) Normal operation (no boost) 20 26 32
Bit 2: Receive Synchronization G.703 Clock Enable (RSCLKE) 0 = disable 1.544MHz (T1)/2.048MHz (E1) synchronization receive mode 1 = enable 1.544MHz (T1)/2.048MHz (E1) synchronization receive mode Bit 1: Transmit Synchronization G.703 Clock Enable (TSCLKE) 0 = disable 1.544MHz (T1)/2.048MHz (E1) transmit synchronization clock 1 = enable 1.544MHz (T1)/2.048MHz (E1) transmit synchronization clock Bit 0: Transmit Alternate Ones and Zeros (TAOZ). Transmit a ...101010... pattern (customer disconnect indication signal) at TTIP and TRING. The transmission of this data pattern is always timed off of TCLKT. 0 = disabled 1 = enabled
252 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CMIE 0 TR.LIC4 Line Interface Control 4 7Bh 6 CMII 0 5 MPS1 0 4 MPS0 0 3 TT1 0 2 TT0 0 1 RT1 0 0 RT0 0
Bit 7: CMI Enable (CMIE) 0 = disable CMI mode 1 = enable CMI mode Bit 6: CMI Invert (CMII) 0 = CMI normal at TTIP and RTIP 1 = invert CMI signal at TTIP and RTIP Bits 4 - 5: MCLK Prescaler T1 Mode: MCLK (MHz) 1.544 3.088 6.176 12.352 2.048 4.096 8.192 16.384 E1 Mode: MCLK (MHz) 2.048 4.096 8.192 16.384 MPS1 0 0 1 1 0 0 1 1 MPS0 0 1 0 1 0 1 0 1 JAMUX (TR.LIC2.3) 0 0 0 0 1 1 1 1 JAMUX (TR.LIC2.3) 0 0 0 0
MPS1 0 0 1 1
MPS0 0 1 0 1
Bits 2 - 3: Transmit Termination Select (TT0, TT1) TT1 0 0 1 1 TT0 0 1 0 1 Internal Transmit-Termination Configuration Internal transmit-side termination disabled Internal transmit -side 75W enabled Internal transmit -side 100W enabled Internal transmit -side 120W enabled
Bits 0 - 1: Receive Termination Select (RT0, RT1) RT1 0 0 1 1 RT0 0 1 0 1 Internal Receive-Termination Configuration Internal receive-side termination disabled Internal receive-side 75W enabled Internal receive-side 100W enabled Internal receive-side 120W enabled
253 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 GRIC 0 TR.IAAR Idle Array Address Register 7Eh 6 GTIC 0 5 IAA5 0 4 IAA4 0 3 IAA3 0 2 IAA2 0 1 IAA1 0 0 IAA0 0
Bit 7: Global Receive-Idle Code (GRIC). Setting this bit causes all receive channels to be set to the idle code written to the TR.PCICR register. This bit must be set = 0 for read operations. The value in bits IAA0-IAA5 must be a valid transmit channel (01h to 20h for E1 mode; 01h to 18h for T1 mode). Bit 6: Global Transmit-Idle Code (GTIC). Setting this bit causes all transmit channels to be set to the idle code written to the PCICR register. This bit must be set = 0 for read operations. The value in bits IAA0-IAA5 must be a valid transmit channel (01h to 20h for E1 mode; 01h to 18h for T1 mode). GRIC 0 0 1 1 GTIC 0 1 0 1 FUNCTION Updates a single transmit or receive channel Updates all transmit channels Updates all receive channels Updates all transmit and receive channels
Bits 0 - 5: Channel Pointer Address Bits (IAA0 to IAA5). These bits select the channel to be programmed with the idle code defined in the TR.PCICR register. IAA0 is the LSB of the 5-bit channel code. Channel 1 is 01h. Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.PCICR Per-Channel Idle Code Register 7Fh 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bits 0 - 7: Per-Channel Idle-Code Bits (C0 to C7). This register defines the idle code to be programmed in the channel selected by the TR.IAAR register. C0 is the LSB of the idle code (this bit is transmitted last). Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0 TR.TCICE1 Transmit-Channel Idle-Code Enable Register 1 80h 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Transmit Channels 1 to 8 Code Insertion Control Bits (CH1 to CH8) 0 = do not insert data from the idle-code array into the transmit data stream 1 = insert data from the idle-code array into the transmit data stream
254 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.TCICE2 Transmit-Channel Idle-Code Enable Register 2 81h 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Transmit Channels 9 to 16 Code Insertion Control Bits (CH9 to CH16) 0 = do not insert data from the idle-code array into the transmit data stream 1 = insert data from the idle code-array into the transmit data stream Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.TCICE3 Transmit-Channel Idle-Code Enable Register 3 82h 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Transmit Channels 17 to 24 Code Insertion Control Bits (CH17 to CH24) 0 = do not insert data from the idle-code array into the transmit data stream 1 = insert data from the idle code-array into the transmit data stream Register Name: Register Description: Register Address: Bit # Name Default 7 CH32 0 TR.TCICE4 Transmit-Channel Idle-Code Enable Register 4 83h 6 CH31 0 5 CH30 0 4 CH29 0 3 CH28 0 2 CH27 0 1 CH26 0 0 CH25 0
Bits 0 - 7: Transmit Channels 25 to 32 Code Insertion Control Bits (CH25 to CH32) 0 = do not insert data from the idle-code array into the transmit data stream 1 = insert data from the idle-code array into the transmit data stream Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0 TR.RCICE1 Receive-Channel Idle-Code Enable Register 1 84h 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Receive Channels 1 to 8 Code Insertion Control Bits (CH1 to CH8) 0 = do not insert data from the idle-code array into the receive data stream 1 = insert data from the idle-code array into the receive data stream
255 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.RCICE2 Receive-Channel Idle-Code Enable Register 2 85h 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Receive Channels 9 to 16 Code Insertion Control Bits (CH9 to CH16) 0 = do not insert data from the idle-code array into the receive data stream 1 = insert data from the idle-code array into the receive data stream Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.RCICE3 Receive-Channel Idle-Code Enable Register 3 86h 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Receive Channels 17 to 24 Code Insertion Control Bits (CH17 to CH24) 0 = do not insert data from the idle-code array into the receive data stream 1 = insert data from the idle-code array into the receive data stream Register Name: Register Description: Register Address: Bit # Name Default 7 CH32 0 TR.RCICE4 Receive-Channel Idle-Code Enable Register 4 87h 6 CH31 0 5 CH30 0 4 CH29 0 3 CH28 0 2 CH27 0 1 CH26 0 0 CH25 0
Bits 0 - 7: Receive Channels 25 to 32 Code Insertion Control Bits (CH25 to CH32) 0 = do not insert data from the idle-code array into the receive data stream 1 = insert data from the idle-code array into the receive data stream Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0 TR.RCBR1 Receive Channel Blocking Register 1 88h 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Receive Channels 1 to 8 Channel Blocking Control Bits (CH1 to CH8) 0 = force the RCHBLK pin to remain low during this channel time 1 = force the RCHBLK pin high during this channel time
256 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.RCBR2 Receive Channel Blocking Register 2 89h 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Receive Channels 9 to 16 Channel Blocking Control Bits (CH9 to CH16) 0 = force the RCHBLK pin to remain low during this channel time 1 = force the RCHBLK pin high during this channel time Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.RCBR3 Receive Channel Blocking Register 3 8Ah 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Receive Channels 17 to 24 Channel Blocking Control Bits (CH17 to CH24) 0 = force the RCHBLK pin to remain low during this channel time 1 = force the RCHBLK pin high during this channel time Register Name: Register Description: Register Address: Bit # Name Default 7 CH32 0 TR.RCBR4 Receive Channel Blocking Register 4 8Bh 6 CH31 0 5 CH30 0 4 CH29 0 3 CH28 0 2 CH27 0 1 CH26 0 0 CH25 0
Bits 0 - 7: Receive Channels 25 to 32 Channel Blocking Control Bits (CH25 to CH32) 0 = force the RCHBLK pin to remain low during this channel time 1 = force the RCHBLK pin high during this channel time
257 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 CH8 0
TR.TCBR1 Transmit Channel Blocking Register 1 8Ch 6 CH7 0 5 CH6 0 4 CH5 0 3 CH4 0 2 CH3 0 1 CH2 0 0 CH1 0
Bits 0 - 7: Transmit Channels 1 to 8 Channel Blocking Control Bits (CH1 to CH8) 0 = force the TCHBLK pin to remain low during this channel time 1 = force the TCHBLK pin high during this channel time Register Name: Register Description: Register Address: Bit # Name Default 7 CH16 0 TR.TCBR2 Transmit Channel Blocking Register 2 8Dh 6 CH15 0 5 CH14 0 4 CH13 0 3 CH12 0 2 CH11 0 1 CH10 0 0 CH9 0
Bits 0 - 7: Transmit Channels 9 to 16 Channel Blocking Control Bits (CH9 to CH16) 0 = force the TCHBLK pin to remain low during this channel time 1 = force the TCHBLK pin high during this channel time Register Name: Register Description: Register Address: Bit # Name Default 7 CH24 0 TR.TCBR3 Transmit Channel Blocking Register 3 8Eh 6 CH23 0 5 CH22 0 4 CH21 0 3 CH20 0 2 CH19 0 1 CH18 0 0 CH17 0
Bits 0 - 7: Transmit Channels 17 to 24 Channel Blocking Control Bits (CH17 to CH24) 0 = force the TCHBLK pin to remain low during this channel time 1 = force the TCHBLK pin high during this channel time Register Name: Register Description: Register Address: Bit # Name Default 7 CH32 0 TR.TCBR4 Transmit Channel Blocking Register 4 8Fh 6 CH31 0 5 CH30 0 4 CH29 0 3 CH28 0 2 CH27 0 1 CH26 0 0 CH25 0
Bits 0 - 7: Transmit Channels 25 to 32 Channel Blocking Control Bits (CH25 to CH32) 0 = force the TCHBLK pin to remain low during this channel time 1 = force the TCHBLK pin high during this channel time
258 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 NOFS 0 TR.H1TC, TR.H2TC HDLC #1 Transmit Control HDLC #2 Transmit Control 90h, A0h 6 TEOML 0 5 THR 0 4 THMS 0 3 TFS 0 2 TEOM 0 1 TZSD 0 0 TCRCD 0
Bit 7: Number of Flags Select (NOFS) 0 = send one flag between consecutive messages 1 = send two flags between consecutive messages Bit 6: Transmit End of Message and Loop (TEOML). To loop on a message, this bit should be set to a 1 just before the last data byte of an HDLC packet is written into the transmit FIFO. The message repeats until the user clears this bit or a new message is written to the transmit FIFO. If the host clears the bit, the looping message completes, then flags are transmitted until a new message is written to the FIFO. If the host terminates the loop by writing a new message to the FIFO, the loop terminates, one or two flags are transmitted, and the new message starts. If not disabled through TCRCD, the transmitter automatically appends a 2-byte CRC code to the end of all messages. This is useful for transmitting consecutive SS7 FISUs without host intervention. Bit 5: Transmit HDLC Reset (THR). Resets the transmit HDLC controller and flushes the transmit FIFO. An abort followed by 7Eh or FFh flags/idle is transmitted until a new packet is initiated by writing new data into the FIFO. Must be cleared and set again for a subsequent reset. 0 = normal operation 1 = reset transmit HDLC controller and flush the transmit FIFO Bit 4: Transmit HDLC Mapping Select (THMS) 0 = transmit HDLC assigned to channels 1 = transmit HDLC assigned to FDL (T1 mode), Sa bits (E1 mode) Bit 3: Transmit Flag/Idle Select (TFS). This bit selects the intermessage fill character after the closing and before the opening flags (7Eh). 0 = 7Eh 1 = FFh Bit 2: Transmit End of Message (TEOM). Should be set to a 1 just before the last data byte of an HDLC packet is written into the transmit FIFO at HxTF. If not disabled through TCRCD, the transmitter automatically appends a 2byte CRC code to the end of the message. Bit 1: Transmit Zero-Stuffer Defeat (TZSD). The zero-stuffer function automatically inserts a 0 in the message field (between the flags) after five consecutive 1s to prevent the emulation of a flag or abort sequence by the data pattern. The receiver automatically removes (destuffs) any 0 after five 1s in the message field. 0 = enable the zero stuffer (normal operation) 1 = disable the zero stuffer Bit 0: Transmit CRC Defeat (TCRCD). A 2-byte CRC code is automatically appended to the outbound message. This bit can be used to disable the CRC function. 0 = enable CRC generation (normal operation) 1 = disable CRC generation
259 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.H1FC, TR.H2FC HDLC # 1 FIFO Control HDLC # 2 FIFO Control 91h, A1h 6 -- 0 5 TFLWM2 0 4 TFLWM1 0 3 TFLWM0 0 2 RFHWM2 0 1 RFHWM1 0 0 RFHWM0 0
Bits 3 - 5: Transmit FIFO Low-Watermark Select (TFLWM0 to TFLWM2) TFLWM2 0 0 0 0 1 1 1 1 TFLWM1 0 0 1 1 0 0 1 1 TFLWM0 0 1 0 1 0 1 0 1 Transmit FIFO Watermark (bytes) 4 16 32 48 64 80 96 112
Bits 0 - 2: Receive FIFO High-Watermark Select (RFHWM0 to RFHWM2) RFHWM2 0 0 0 0 1 1 1 1 RFHWM1 0 0 1 1 0 0 1 1 RFHWM0 0 1 0 1 0 1 0 1 Receive FIFO Watermark (bytes) 4 16 32 48 64 80 96 112
260 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RHCS7 0 TR.H1RCS1, TR.H1RCS2, TR.H1RCS3, TR.H1RCS4 TR.H2RCS1, TR.H2RCS2, TR.H2RCS3, TR.H2RCS4 HDLC # 1 Receive Channel Select HDLC # 2 Receive Channel Select 92h, 93h, 94h, 95h A2h, A3h, A4h, A5h 6 RHCS6 0 5 RHCS5 0 4 RHCS4 0 3 RHCS3 0 2 RHCS2 0 1 RHCS1 0 0 RHCS0 0
Bit 7: Receive HDLC Channel Select Bit 7 (RHCS7). Select Channel 8, 16, 24, or 32. Bit 6: Receive HDLC Channel Select Bit 6 (RHCS6). Select Channel 7, 15, 23, or 31. Bit 5: Receive HDLC Channel Select Bit 5 (RHCS5). Select Channel 6, 14, 22, or 30. Bit 4: Receive HDLC Channel Select Bit 4 (RHCS4). Select Channel 5, 13, 21, or 29. Bit 3: Receive HDLC Channel Select Bit 3 (RHCS3). Select Channel 4, 12, 20, or 28. Bit 2: Receive HDLC Channel Select Bit 2 (RHCS2). Select Channel 3, 11, 19, or 27. Bit 1: Receive HDLC Channel Select Bit 1 (RHCS1). Select Channel 2, 10, 18, or 26. Bit 0: Receive HDLC Channel Select Bit 0 (RHCS0). Select Channel 1, 9, 17, or 25.
261 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RCB8SE 0 TR.H1RTSBS, TR.H2RTSBS HDLC # 1 Receive Time Slot Bits/Sa Bits Select HDLC # 2 Receive Time Slot Bits/Sa Bits Select 96h, A6h 6 RCB7SE 0 5 RCB6SE 0 4 RCB5SE 0 3 RCB4SE 0 2 RCB3SE 0 1 RCB2SE 0 0 RCB1SE 0
Bit 7: Receive Channel Bit 8 Suppress Enable (RCB8SE). MSB of the channel. Set to 1 to stop this bit from being used. Bit 6: Receive Channel Bit 7 Suppress Enable (RCB7SE). Set to 1 to stop this bit from being used. Bit 5: Receive Channel Bit 6 Suppress Enable (RCB6SE). Set to 1 to stop this bit from being used. Bit 4: Receive Channel Bit 5 Suppress Enable/Sa4 Bit Enable (RCB5SE). Set to 1 to stop this bit from being used. Bit 3: Receive Channel Bit 4 Suppress Enable/Sa5 Bit Enable (RCB4SE). Set to 1 to stop this bit from being used. Bit 2: Receive Channel Bit 3 Suppress Enable/Sa6 Bit Enable (RCB3SE). Set to 1 to stop this bit from being used. Bit 1: Receive Channel Bit 2 Suppress Enable/Sa7 Bit Enable (RCB2SE). Set to 1 to stop this bit from being used. Bit 0: Receive Channel Bit 1 Suppress Enable/Sa8 Bit Enable (RCB1SE ). LSB of the channel. Set to 1 to stop this bit from being used.
262 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 THCS7 0 TR.H1TCS1, TR.H1TCS2, TR.H1TCS3, TR.H1TCS4 TR.H2TCS1, TR.H2TCS2, TR.H2TCS3, TR.H2TCS4 HDLC # 1 Transmit Channel Select HDLC # 2 Transmit Channel Select 97h, 98h, 99h, 9Ah A7h, A8h, A9h, AAh 6 THCS6 0 5 THCS5 0 4 THCS4 0 3 THCS3 0 2 THCS2 0 1 THCS1 0 0 THCS0 0
Bit 7: Transmit HDLC Channel Select Bit 7 (THCS7). Select Channel 8, 16, 24, or 32. Bit 6: Transmit HDLC Channel Select Bit 6 (THCS6). Select Channel 7, 15, 23, or 31. Bit 5: Transmit HDLC Channel Select Bit 5 (THCS5). Select Channel 6, 14, 22, or 30. Bit 4: Transmit HDLC Channel Select Bit 4 (THCS4). Select Channel 5, 13, 21, or 29. Bit 3: Transmit HDLC Channel Select Bit 3 (THCS3). Select Channel 4, 12, 20, or 28. Bit 2: Transmit HDLC Channel Select Bit 2 (THCS2). Select Channel 3, 11, 19, or 27. Bit 1: Transmit HDLC Channel Select Bit 1 (THCS1). Select Channel 2, 10, 18, or 26. Bit 0: Transmit HDLC Channel Select Bit 0 (THCS0). Select Channel 1, 9, 17, or 25.
263 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TCB8SE 0 TR.H1TTSBS, TR.H2TTSBS HDLC # 1 Transmit Time Slot Bits/Sa Bits Select HDLC # 2 Transmit Time Slot Bits/Sa Bits Select 9Bh, ABh 6 TCB7SE 0 5 TCB6SE 0 4 TCB5SE 0 3 TCB4SE 0 2 TCB3SE 0 1 TCB2SE 0 0 TCB1SE 0
Bit 7: Transmit Channel Bit 8 Suppress Enable (TCB1SE). MSB of the channel. Set to 1 to stop this bit from being used. Bit 6: Transmit Channel Bit 7 Suppress Enable (TCB1SE). Set to 1 to stop this bit from being used. Bit 5: Transmit Channel Bit 6 Suppress Enable (TCB1SE). Set to 1 to stop this bit from being used. Bit 4: Transmit Channel Bit 5 Suppress Enable/Sa4 Bit Enable (TCB1SE). Set to 1 to stop this bit from being used. Bit 3: Transmit Channel Bit 4 Suppress Enable/Sa5 Bit Enable (TCB1SE). Set to 1 to stop this bit from being used. Bit 2: Transmit Channel Bit 3 Suppress Enable/Sa6 Bit Enable (TCB1SE). Set to 1 to stop this bit from being used. Bit 1: Transmit Channel Bit 2 Suppress Enable/Sa7 Bit Enable (TCB1SE). Set to 1 to stop this bit from being used. Bit 0: Transmit Channel Bit 1 Suppress Enable/Sa8 Bit Enable (TCB1SE). LSB of the channel. Set to 1 to stop this bit from being used. Register Name: Register Description: Register Address: Bit # Name Default 7 MS 0 TR.H1RPBA, TR.H2RPBA HDLC # 1 Receive Packet Bytes Available HDLC # 2 Receive Packet Bytes Available 9Ch, ACh 6 RPBA6 0 5 RPBA5 0 4 RPBA4 0 3 RPBA3 0 2 RPBA2 0 1 RPBA1 0 0 RPBA0 0
Bit 7: Message Status (MS) 0 = bytes indicated by RPBA0 through RPBA6 are the end of a message. Host must check the INFO5 or INFO6 register for details. 1 = bytes indicated by RPBA0 through RPBA6 are the beginning or continuation of a message. The host does not need to check the INFO5 or INFO6 register. Bits 0 - 6: Receive FIFO Packet Bytes Available Count (RPBA0 to RPBA6). RPBA0 is the LSB.
264 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 THD7 0 TR.H1TF, TR.H2TF HDLC # 1 Transmit FIFO HDLC # 2 Transmit FIFO 9Dh, ADh 6 THD6 0 5 THD5 0 4 THD4 0 3 THD3 0 2 THD2 0 1 THD1 0 0 THD0 0
Bit 7: Transmit HDLC Data Bit 7 (THD7). MSB of an HDLC packet data byte. Bit 6: Transmit HDLC Data Bit 6 (THD6) Bit 5: Transmit HDLC Data Bit 5 (THD5) Bit 4: Transmit HDLC Data Bit 4 (THD4) Bit 3: Transmit HDLC Data Bit 3 (THD3) Bit 2: Transmit HDLC Data Bit 2 (THD2) Bit 1: Transmit HDLC Data Bit 1 (THD1) Bit 0: Transmit HDLC Data Bit 0 (THD0). LSB of an HDLC packet data byte. Register Name: Register Description: Register Address: Bit # Name Default 7 RHD7 0 TR.H1RF, TR.H2RF HDLC # 1 Receive FIFO HDLC # 2 Receive FIFO 9Eh, AEh 6 RHD6 0 5 RHD5 0 4 RHD4 0 3 RHD3 0 2 RHD2 0 1 RHD1 0 0 RHD0 0
Bit 7: Receive HDLC Data Bit 7 (RHD7). MSB of an HDLC packet data byte. Bit 6: Receive HDLC Data Bit 6 (RHD6) Bit 5: Receive HDLC Data Bit 5 (RHD5) Bit 4: Receive HDLC Data Bit 4 (RHD4) Bit 3: Receive HDLC Data Bit 3 (RHD3) Bit 2: Receive HDLC Data Bit 2 (RHD2) Bit 1: Receive HDLC Data Bit 1 (RHD1) Bit 0: Receive HDLC Data Bit 0 (RHD0). LSB of an HDLC packet data byte.
265 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TFBA7 0 TR.H1TFBA, TR.H2TFBA HDLC # 1 Transmit FIFO Buffer Available HDLC # 2 Transmit FIFO Buffer Available 9Fh, Afh 6 TFBA6 0 5 TFBA5 0 4 TFBA4 0 3 TFBA3 0 2 TFBA2 0 1 TFBA1 0 0 TFBA0 0
Bits 0 - 7: Transmit FIFO Bytes Available (TFBAO to TFBA7). TFBA0 is the LSB. Register Name: Register Description: Register Address: Bit # Name Default 7 TC1 0 TR.IBCC In-Band Code Control Register B6h 6 TC0 0 5 RUP2 0 4 RUP1 0 3 RUP0 0 2 RDN2 0 1 RDN1 0 0 RDN0 0
Bits 6 - 7: Transmit Code Length Definition Bits (TC0 to TC1) TC1 0 0 1 1 TC0 0 1 0 1 Length Selected (bits) 5 6/3 7 16/8/4/2/1
Bits 3 - 5: Receive Up-Code Length Definition Bits (RUP0 to RUP2) RUP2 0 0 0 0 1 1 1 1 RUP1 0 0 1 1 0 0 1 1 RUP0 0 1 0 1 0 1 0 1 Length Selected (bits) 1 2 3 4 5 6 7 8/16
Bits 0 - 2: Receive Down-Code Length Definition Bits (RDN0 to RDN2) RDN2 0 0 0 0 1 1 1 1 RDN1 0 0 1 1 0 0 1 1 RDN0 0 1 0 1 0 1 0 1 Length Selected (bits) 1 2 3 4 5 6 7 8/16
266 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.TCD1 Transmit Code-Definition Register 1 B7h 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bit 7: Transmit Code-Definition Bit 7 (C7). First bit of the repeating pattern. Bits 3 - 6: Transmit Code-Definition Bits 3-6 (C3-C6) Bit 2: Transmit Code-Definition Bit 2 (C2). A don't care if a 5-bit length is selected. Bit 1: Transmit Code-Definition Bit 1 (C1). A don't care if a 5-bit or 6-bit length is selected. Bit 0: Transmit Code-Definition Bit 0 (C0). A don't care if a 5-, 6-, or 7-bit length is selected. Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.TCD2 Transmit Code Definition Register 2 B8h 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Least significant byte of 16 bit code. Bits 0 - 7: Transmit Code-Definition Bits 0-7 (C0-C7). A don't care if a 5-, 6-, or 7-bit length is selected.
267 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: TR.RUPCD1 Receive Up-Code Definition Register 1 B9h 2 C2 0 1 C1 0 0 C0 0
Bit # 7 6 5 4 3 Name C7 C6 C5 C4 C3 Default 0 0 0 0 0 Note: Writing this register resets the detector's integration period.
Bit 7: Receive Up-Code Definition Bit 7 (C7). First bit of the repeating pattern. Bit 6: Receive Up-Code Definition Bit 6 (C6). A don't care if a 1-bit length is selected. Bit 5: Receive Up-Code Definition Bit 5 (C5). A don't care if a 1-bit or 2-bit length is selected. Bit 4: Receive Up-Code Definition Bit 4 (C4). A don't care if a 1-bit to 3-bit length is selected. Bit 3: Receive Up-Code Definition Bit 3 (C3). A don't care if a 1-bit to 4-bit length is selected. Bit 2: Receive Up-Code Definition Bit 2 (C2). A don't care if a 1-bit to 5-bit length is selected. Bit 1: Receive Up-Code Definition Bit 1 (C1). A don't care if a 1-bit to 6-bit length is selected. Bit 0: Receive Up-Code Definition Bit 0 (C0). A don't care if a 1-bit to 7-bit length is selected. Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.RUPCD2 Receive Up-Code Definition Register 2 BAh 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bits 0 - 7: Receive Up-Code Definition Bits 0-7 (C0-C7). A don't care if a 1-bit to 7-bit length is selected.
268 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: TR.RDNCD1 Receive Down-Code Definition Register 1 BBh 2 C2 0 1 C1 0 0 C0 0
Bit # 7 6 5 4 3 Name C7 C6 C5 C4 C3 Default 0 0 0 0 0 Note: Writing this register resets the detector's integration period.
Bit 7: Receive Down-Code Definition Bit 7 (C7). First bit of the repeating pattern. Bit 6: Receive Down-Code Definition Bit 6 (C6). A don't care if a 1-bit length is selected. Bit 5: Receive Down-Code Definition Bit 5 (C5). A don't care if a 1-bit or 2-bit length is selected. Bit 4: Receive Down-Code Definition Bit 4 (C4). A don't care if a 1-bit to 3-bit length is selected. Bit 3: Receive Down-Code Definition Bit 3 (C3). A don't care if a 1-bit to 4-bit length is selected. Bit 2: Receive Down-Code Definition Bit 2 (C2). A don't care if a 1-bit to 5-bit length is selected. Bit 1: Receive Down-Code Definition Bit 1 (C1). A don't care if a 1-bit to 6-bit length is selected. Bit 0: Receive Down-Code Definition Bit 0 (C0). A don't care if a 1-bit to 7-bit length is selected. Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.RDNCD2 Receive Down-Code Definition Register 2 BCh 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bits 0 - 7: Receive Down-Code Definition Bits 0-7 (C0-C7). A don't care if a 1-bit to 7-bit length is selected.
269 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.RSCC In-Band Receive Spare Control Register BDh 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 RSC2 0 1 RSC1 0 0 RSC0 0
Bits 3 - 7: Unused, must be set to 0 for proper operation Bits 0 - 2: Receive Spare Code Length Definition Bits (RSC0 to RSC2) RSC2 0 0 0 0 1 1 1 1 RSC1 0 0 1 1 0 0 1 1 RSC0 0 1 0 1 0 1 0 1 Length Selected (bits) 1 2 3 4 5 6 7 8/16
270 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: TR.RSCD1 Receive Spare-Code Definition Register 1 BEh 2 C2 0 1 C1 0 0 C0 0
Bit # 7 6 5 4 3 Name C7 C6 C5 C4 C3 Default 0 0 0 0 0 Note: Writing this register resets the detector's integration period.
Bit 7: Receive Spare-Code Definition Bit 7 (C7). First bit of the repeating pattern. Bit 6: Receive Spare-Code Definition Bit 6 (C6). A don't care if a 1-bit length is selected. Bit 5: Receive Spare-Code Definition Bit 5 (C5). A don't care if a 1-bit or 2-bit length is selected. Bit 4: Receive Spare-Code Definition Bit 4 (C4). A don't care if a 1-bit to 3-bit length is selected. Bit 3: Receive Spare-Code Definition Bit 3 (C3). A don't care if a 1-bit to 4-bit length is selected. Bit 2: Receive Spare-Code Definition Bit 2 (C2). A don't care if a 1-bit to 5-bit length is selected. Bit 1: Receive Spare-Code Definition Bit 1 (C1). A don't care if a 1-bit to 6-bit length is selected. Bit 0: Receive Spare-Code Definition Bit 0 (C0). A don't care if a 1-bit to 7-bit length is selected. Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.RSCD2 Receive Spare Code Definition Register 2 BFh 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bits 0 - 7: Receive Spare-Code Definition Bits 0-7 (C0-C7). A don't care if a 1-bit to 7-bit length is selected.
271 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.RFDL (TR.BOCC.4 = 1) Receive FDL Register C0h 6 -- 0 5 RBOC5 0 4 RBOC4 0 3 RBOC3 0 2 RBOC2 0 1 RBOC1 0 0 RBOC0 0
RFDL register bit definitions when TR.BOCC.4 = 1: Bit 5: BOC Bit 5 (RBOC5) Bit 4: BOC Bit 4 (RBOC4) Bit 3: BOC Bit 3 (RBOC3) Bit 2: BOC Bit 2 (RBOC2) Bit 1: BOC Bit 1 (RBOC1) Bit 0: BOC Bit 0 (RBOC0) Register Name: Register Description: Register Address: Bit # Name Default 7 RFDL7 0 TR.RFDL (TR.BOCC.4 = 0) Receive FDL Register C0h 6 RFDL6 0 5 RFDL5 0 4 RFDL4 0 3 RFDL3 0 2 RFDL2 0 1 RFDL1 0 0 RFDL0 0
The receive FDL register (TR.RFDL) reports the incoming FDL or the incoming Fs bits. The LSB is received first. Bit 7: Receive FDL Bit 7 (RFDL7). MSB of the received FDL code. Bit 6: Receive FDL Bit 6 (RFDL6) Bit 5: Receive FDL Bit 5 (RFDL5) Bit 4: Receive FDL Bit 4 (RFDL4) Bit 3: Receive FDL Bit 3 (RFDL3) Bit 2: Receive FDL Bit 2 (RFDL2) Bit 1: Receive FDL Bit 1 (RFDL1) Bit 0: Receive FDL Bit 0 (RFDL0). LSB of the received FDL code.
272 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: TR.TFDL Transmit FDL Register C1h 2 TFDL2 0 1 TFDL1 0 0 TFDL0 0
Bit # 7 6 5 4 3 Name TFDL7 TFDL6 TFDL5 TFDL4 TFDL3 Default 0 0 0 0 0 Note: Also used to insert Fs framing pattern in D4 framing mode.
The transmit FDL register (TR.TFDL) contains the FDL information that is to be inserted on a byte basis into the outgoing T1 data stream. The LSB is transmitted first. Bit 7: Transmit FDL Bit 7 (TFDL7). MSB of the transmit FDL code. Bit 6: Transmit FDL Bit 6 (TFDL6) Bit 5: Transmit FDL Bit 5 (TFDL5) Bit 4: Transmit FDL Bit 4 (TFDL4) Bit 3: Transmit FDL Bit 3 (TFDL3) Bit 2: Transmit FDL Bit 2 (TFDL2) Bit 1: Transmit FDL Bit 1 (TFDL1) Bit 0: Transmit FDL Bit 0 (TFDL0). LSB of the transmit FDL code. Register Name: Register Description: Register Address: Bit # Name Default 7 RFDLM7 0 TR.RFDLM1, TR.RFDLM2 Receive FDL Match Register 1 Receive FDL Match Register 2 C2h, C3h 6 RFDLM6 0 5 RFDLM5 0 4 RFDLM4 0 3 RFDLM3 0 2 RFDLM2 0 1 RFDLM1 0 0 RFDLM0 0
Bit 7: Receive FDL Match Bit 7 (RFDLM7). MSB of the FDL match code. Bit 6: Receive FDL Match Bit 6 (RFDLM6) Bit 5: Receive FDL Match Bit 5 (RFDLM5) Bit 4: Receive FDL Match Bit 4 (RFDLM4) Bit 3: Receive FDL Match Bit 3 (RFDLM3) Bit 2: Receive FDL Match Bit 2 (RFDLM2) Bit 1: Receive FDL Match Bit 1 (RFDLM1) Bit 0: Receive FDL Match Bit 0 (RFDLM0). LSB of the FDL match code.
273 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 Si 0 TR.RAF Receive Align Frame Register C6h 6 0 0 5 0 0 4 1 0 3 1 0 2 0 0 1 1 0 0 1 0
Bit 7: International Bit (Si) Bit 6: Frame Alignment Signal Bit (0) Bit 5: Frame Alignment Signal Bit (0) Bit 4: Frame Alignment Signal Bit (1) Bit 3: Frame Alignment Signal Bit (1) Bit 2: Frame Alignment Signal Bit (0) Bit 1: Frame Alignment Signal Bit (1) Bit 0: Frame Alignment Signal Bit (1) Register Name: Register Description: Register Address: Bit # Name Default 7 Si 0 TR.RNAF Receive Nonalign Frame Register C7h 6 1 0 5 A 0 4 Sa4 0 3 Sa5 0 2 Sa6 0 1 Sa7 0 0 Sa8 0
Bit 7: International Bit (Si) Bit 6: Frame Nonalignment Signal Bit (1) Bit 5: Remote Alarm (A) Bit 4: Additional Bit 4 (Sa4) Bit 3: Additional Bit 5 (Sa5) Bit 2: Additional Bit 6 (Sa6) Bit 1: Additional Bit 7 (Sa7) Bit 0: Additional Bit 8 (Sa8)
274 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 SiF0 0 TR.RSiAF Received Si Bits of the Align Frame C8h 6 SiF2 0 5 SiF4 0 4 SiF6 0 3 SiF8 0 2 SiF10 0 1 SiF12 0 0 SiF14 0
Bit 7: Si Bit of Frame 0 (SiF0) Bit 6: Si Bit of Frame 2 (SiF2) Bit 5: Si Bit of Frame 4 (SiF4) Bit 4: Si Bit of Frame 6 (SiF6) Bit 3: Si Bit of Frame 8 (SiF8) Bit 2: Si Bit of Frame 10 (SiF10) Bit 1: Si Bit of Frame 12 (SiF12) Bit 0: Si Bit of Frame 14 (SiF14) Register Name: Register Description: Register Address: Bit # Name Default 7 SiF1 0 TR.RSiNAF Received Si Bits of the Nonalign Frame C9h 6 SiF3 0 5 SiF5 0 4 SiF7 0 3 SiF9 0 2 SiF11 0 1 SiF13 0 0 SiF15 0
Bit 7: Si Bit of Frame 1 (SiF1) Bit 6: Si Bit of Frame 3 (SiF3) Bit 5: Si Bit of Frame 5 (SiF5) Bit 4: Si Bit of Frame 7 (SiF7) Bit 3: Si Bit of Frame 9 (SiF9) Bit 2: Si Bit of Frame 11 (SiF11) Bit 1: Si Bit of Frame 13 (SiF13) Bit 0: Si Bit of Frame 15 (SiF15)
275 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RRAF1 0 TR.RRA Received Remote Alarm Cah 6 RRAF3 0 5 RRAF5 0 4 RRAF7 0 3 RRAF9 0 2 RRAF11 0 1 RRAF13 0 0 RRAF15 0
Bit 7: Remote Alarm Bit of Frame 1 (RRAF1) Bit 6: Remote Alarm Bit of Frame 3 (RRAF3) Bit 5: Remote Alarm Bit of Frame 5 (RRAF5) Bit 4: Remote Alarm Bit of Frame 7 (RRAF7) Bit 3: Remote Alarm Bit of Frame 9 (RRAF9) Bit 2: Remote Alarm Bit of Frame 11 (RRAF11) Bit 1: Remote Alarm Bit of Frame 13 (RRAF13) Bit 0: Remote Alarm Bit of Frame 15 (RRAF15) Register Name: Register Description: Register Address: Bit # Name Default 7 RSa4F1 0 TR.RSa4 Received Sa4 Bits CBh 6 RSa4F3 0 5 RSa4F5 0 4 RSa4F7 0 3 RSa4F9 0 2 RSa4F11 0 1 RSa4F13 0 0 RSa4F15 0
Bit 7: Sa4 Bit of Frame 1 (RSa4F1) Bit 6: Sa4 Bit of Frame 3 (RSa4F3) Bit 5: Sa4 Bit of Frame 5(RSa4F5) Bit 4: Sa4 Bit of Frame 7 (RSa4F7) Bit 3: Sa4 Bit of Frame 9 (RSa4F9) Bit 2: Sa4 Bit of Frame 11 (RSa4F11) Bit 1: Sa4 Bit of Frame 13 (RSa4F13) Bit 0: Sa4 Bit of Frame 15 (RSa4F15)
276 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RSa5F1 0 TR.RSa5 Received Sa5 Bits CCh 6 RSa5F3 0 5 RSa5F5 0 4 RSa5F7 0 3 RSa5F9 0 2 RSa5F11 0 1 RSa5F13 0 0 RSa5F15 0
Bit 7: Sa5 Bit of Frame 1 (RSa5F1) Bit 6: Sa5 Bit of Frame 3 (RSa5F3) Bit 5: Sa5 Bit of Frame 5 (RSa5F5) Bit 4: Sa5 Bit of Frame 7 (RSa5F7) Bit 3: Sa5 Bit of Frame 9 (RSa5F9) Bit 2: Sa5 Bit of Frame 11 (RSa5F11) Bit 1: Sa5 Bit of Frame 13 (RSa5F13) Bit 0: Sa5 Bit of Frame 15 (RSa5F15)
Register Name: Register Description: Register Address: Bit # Name Default 7 RSa6F1 0
TR.RSa6 Received Sa6 Bits CDh 6 RSa6F3 0 5 RSa6F5 0 4 RSa6F7 0 3 RSa6F9 0 2 RSa6F11 0 1 RSa6F13 0 0 RSa6F15 0
Bit 7: Sa6 Bit of Frame 3(RSa6F3) Bit 6: Sa6 Bit of Frame 4 (RSa6F4) Bit 5: Sa6 Bit of Frame 5 (RSa6F5) Bit 4: Sa6 Bit of Frame 7 (RSa6F7) Bit 3: Sa6 Bit of Frame 9 (RSa6F9) Bit 2: Sa6 Bit of Frame 11 (RSa6F11) Bit 1: Sa6 Bit of Frame 13 (RSa6F13) Bit 0: Sa6 Bit of Frame 15 (RSa6F15)
277 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RSa7F1 0 TR.RSa7 Received Sa7 Bits CEh 6 Rsa7F3 0 5 RSa7F5 0 4 RSa7F7 0 3 RSa7F9 0 2 RSa7F11 0 1 RSa7F13 0 0 RSa7F15 0
Bit 7: Sa7 Bit of Frame 1(RSa4F1) Bit 6: Sa7 Bit of Frame 3 (RSa7F3) Bit 5: Sa7 Bit of Frame 5 (RSa7F5) Bit 4: Sa7 Bit of Frame 7 (RSa7F7) Bit 3: Sa7 Bit of Frame 9 (RSa7F9) Bit 2: Sa7 Bit of Frame 11 (RSa7F11) Bit 1: Sa7 Bit of Frame 13 (RSa7F13) Bit 0: Sa7 Bit of Frame 15 (RSa7F15)
Register Name: Register Description: Register Address: Bit # Name Default 7 RSa8F1 0
TR.RSa8 Received Sa8 Bits CFh 6 RSa8F3 0 5 RSa8F5 0 4 RSa8F7 0 3 RSa8F9 0 2 RSa8F11 0 1 RSa8F13 0 0 RSa8F15 0
Bit 7: Sa8 Bit of Frame 1 (RSa8F1) Bit 6: Sa8 Bit of Frame 3 (RSa8F3) Bit 5: Sa8 Bit of Frame 5 (RSa8F5) Bit 4: Sa8 Bit of Frame 7 (RSa8F7) Bit 3: Sa8 Bit of Frame 9 (RSa8F9) Bit 2: Sa8 Bit of Frame 11 (RSa8F11) Bit 1: Sa8 Bit of Frame 13 (RSa8F13) Bit 0: Sa8 Bit of Frame 15 (RSa8F15)
278 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 Si 0 TR.TAF Transmit Align Frame Register D0h 6 0 0 5 0 0 4 1 1 3 1 1 2 0 0 1 1 1 0 1 1
Bit 7: International Bit (Si) Bit 6: Frame Alignment Signal Bit (0) Bit 5: Frame Alignment Signal Bit (0) Bit 4: Frame Alignment Signal Bit (1) Bit 3: Frame Alignment Signal Bit (1) Bit 2: Frame Alignment Signal Bit (0) Bit 1: Frame Alignment Signal Bit (1) Bit 0: Frame Alignment Signal Bit (1)
Register Name: Register Description: Register Address: Bit # Name Default 7 Si 0
TR.TNAF Transmit Nonalign Frame Register D1h 6 1 1 5 A 0 4 Sa4 0 3 Sa5 0 2 Sa6 0 1 Sa7 0 0 Sa8 0
Bit 7: International Bit (Si) Bit 6: Frame Nonalignment Signal Bit (1) Bit 5: Remote Alarm [used to transmit the alarm (A)] Bit 4: Additional Bit 4 (Sa4) Bit 3: Additional Bit 5 (Sa5) Bit 2: Additional Bit 6 (Sa6) Bit 1: Additional Bit 7 (Sa7) Bit 0: Additional Bit 8 (Sa8)
279 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TSiF0 0 TR.TSiAF Transmit Si Bits of the Align Frame D2h 6 TSiF2 0 5 TSiF4 0 4 TSiF6 0 3 TSiF8 0 2 TSiF10 0 1 TSiF12 0 0 TSiF14 0
Bit 7: Si Bit of Frame 0 (TSiF0) Bit 6: Si Bit of Frame 2 (TSiF2) Bit 5: Si Bit of Frame 4 (TSiF4) Bit 4: Si Bit of Frame 6 (TSiF6) Bit 3: Si Bit of Frame 8 (TSiF8) Bit 2: Si Bit of Frame 10 (TSiF10) Bit 1: Si Bit of Frame 12 (TSiF12) Bit 0: Si Bit of Frame 14 (TSiF14) Register Name: Register Description: Register Address: Bit # Name Default 7 TSiF1 0 TR.TSiNAF Transmit Si Bits of the Nonalign Frame D3h 6 TSiF3 0 5 TSiF5 0 4 TSiF7 0 3 TSiF9 0 2 TSiF11 0 1 TSiF13 0 0 TSiF15 0
Bit 7: Si Bit of Frame 1 (TSiF1) Bit 6: Si Bit of Frame 3 (TSiF3) Bit 5: Si Bit of Frame 5 (TSiF5) Bit 4: Si Bit of Frame 7 (TSiF7) Bit 3: Si Bit of Frame 9 (TSiF9) Bit 2: Si Bit of Frame 11 (TSiF11) Bit 1: Si Bit of Frame 13 (TSiF13) Bit 0: Si Bit of Frame 15 (TSiF15)
280 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TRAF1 0 TR.TRA Transmit Remote Alarm D4h 6 TRAF3 0 5 TRAF5 0 4 TRAF7 0 3 TRAF9 0 2 TRAF11 0 1 TRAF13 0 0 TRAF15 0
Bit 7: Remote Alarm Bit of Frame 1 (TRAF1) Bit 6: Remote Alarm Bit of Frame 3 (TRAF3) Bit 5: Remote Alarm Bit of Frame 5 (TRAF5) Bit 4: Remote Alarm Bit of Frame 7 (TRAF7) Bit 3: Remote Alarm Bit of Frame 9 (TRAF9) Bit 2: Remote Alarm Bit of Frame 11 (TRAF11) Bit 1: Remote Alarm Bit of Frame 13 (TRAF13) Bit 0: Remote Alarm Bit of Frame 15 (TRAF15) Register Name: Register Description: Register Address: Bit # Name Default 7 TSa4F1 0 TR.TSa4 Transmit Sa4 Bits D5h 6 TSa4F3 0 5 TSa4F5 0 4 TSa4F7 0 3 TSa4F9 0 2 TSa4F11 0 1 TSa4F13 0 0 TSa4F15 0
Bit 7: Sa4 Bit of Frame 1 (TSa4F1) Bit 6: Sa4 Bit of Frame 3 (TSa4F3) Bit 5: Sa4 Bit of Frame 5 (TSa4F5) Bit 4: Sa4 Bit of Frame 7 (TSa4F7) Bit 3: Sa4 Bit of Frame 9 (TSa4F9) Bit 2: Sa4 Bit of Frame 11 (TSa4F11) Bit 1: Sa4 Bit of Frame 13 (TSa4F13) Bit 0: Sa4 Bit of Frame 15 (TSa4F15)
281 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TSa5F1 0 TR.TSa5 Transmitted Sa5 Bits D6h 6 TSa5F3 0 5 TSa5F5 0 4 TSa5F7 0 3 TSa5F9 0 2 TSa5F11 0 1 TSa5F13 0 0 TSa5F15 0
Bit 7: Sa5 Bit of Frame 1 (TSa5F1) Bit 6: Sa5 Bit of Frame 3 (TSa5F3) Bit 5: Sa5 Bit of Frame 5 (TSa5F5) Bit 4: Sa5 Bit of Frame 7 (TSa5F7) Bit 3: Sa5 Bit of Frame 9 (TSa5F9) Bit 2: Sa5 Bit of Frame 11 (TSa5F11) Bit 1: Sa5 Bit of Frame 13 (TSa5F13) Bit 0: Sa5 Bit of Frame 15 (TSa5F15)
Register Name: Register Description: Register Address: Bit # Name Default 7 TSa6F1 0
TR.TSa6 Transmit Sa6 Bits D7h 6 TSa6F3 0 5 TSa6F5 0 4 TSa6F7 0 3 TSa6F9 0 2 TSa6F11 0 1 TSa6F13 0 0 TSa6F15 0
Bit 7: Sa6 Bit of Frame 1 (TSa6F1) Bit 6: Sa6 Bit of Frame 3 (TSa6F3) Bit 5: Sa6 Bit of Frame 5 (TSa6F5) Bit 4: Sa6 Bit of Frame 7 (TSa6F7) Bit 3: Sa6 Bit of Frame 9 (TSa6F9) Bit 2: Sa6 Bit of Frame 11 (TSa6F11) Bit 1: Sa6 Bit of Frame 13 (TSa6F13) Bit 0: Sa6 Bit of Frame 15 (TSa6F15)
282 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TSa7F1 0 TR.TSa7 Transmit Sa7 Bits D8h 6 TSa7F3 0 5 TSa7F5 0 4 TSa7F7 0 3 TSa7F9 0 2 TSa7F11 0 1 TSa7F13 0 0 TSa7F15 0
Bit 7: Sa7 Bit of Frame 1 (TSa4F1) Bit 6: Sa7 Bit of Frame 3 (TSa7F3) Bit 5: Sa7 Bit of Frame 5 (TSa7F5) Bit 4: Sa7 Bit of Frame 7 (TSa7F7) Bit 3: Sa7 Bit of Frame 9 (TSa7F9) Bit 2: Sa7 Bit of Frame 11 (TSa7F11) Bit 1: Sa7 Bit of Frame 13 (TSa7F13) Bit 0: Sa7 Bit of Frame 15 (TSa7F15) Register Name: Register Description: Register Address: Bit # Name Default 7 TSa8F1 0 TR.TSa8 Transmit Sa8 Bits D9h 6 TSa8F3 0 5 TSa8F5 0 4 TSa8F7 0 3 TSa8F9 0 2 TSa8F11 0 1 TSa8F13 0 0 TSa8F15 0
Bit 7: Sa8 Bit of Frame 1 (TSa8F1) Bit 6: Sa8 Bit of Frame 3 (TSa8F3) Bit 5: Sa8 Bit of Frame 5 (TSa8F5) Bit 4: Sa8 Bit of Frame 7 (TSa8F7) Bit 3: Sa8 Bit of Frame 9 (TSa8F9) Bit 2: Sa8 Bit of Frame 11 (TSa8F11) Bit 1: Sa8 Bit of Frame 13 (TSa8F13) Bit 0: Sa8 Bit of Frame 15 (TSa8F15)
283 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 SiAF 0 TR.TSACR Transmit Sa Bit Control Register DAh 6 SiNAF 0 5 RA 0 4 Sa4 0 3 Sa5 0 2 Sa6 0 1 Sa7 0 0 Sa8 0
Bit 7: International Bit in Align Frame Insertion Control Bit (SiAF) 0 = do not insert data from the TR.TSiAF register into the transmit data stream 1 = insert data from the TR.TSiAF register into the transmit data stream Bit 6: International Bit in Nonalign Frame Insertion Control Bit (SiNAF) 0 = do not insert data from the TR.TSiNAF register into the transmit data stream 1 = insert data from the TR.TSiNAF register into the transmit data stream Bit 5: Remote Alarm Insertion Control Bit (RA) 0 = do not insert data from the TR.TRA register into the transmit data stream 1 = insert data from the TR.TRA register into the transmit data stream Bit 4: Additional Bit 4 Insertion Control Bit (Sa4) 0 = do not insert data from the TR.TSa4 register into the transmit data stream 1 = insert data from the TR.TSa4 register into the transmit data stream Bit 3: Additional Bit 5 Insertion Control Bit (Sa5) 0 = do not insert data from the TR.TSa5 register into the transmit data stream 1 = insert data from the TR.TSa5 register into the transmit data stream Bit 2: Additional Bit 6 Insertion Control Bit (Sa6) 0 = do not insert data from the TR.TSa6 register into the transmit data stream 1 = insert data from the TR.TSa6 register into the transmit data stream Bit 1: Additional Bit 7 Insertion Control Bit (Sa7) 0 = do not insert data from the TR.TSa7 register into the transmit data stream 1 = insert data from the TR.TSa7 register into the transmit data stream Bit 0: Additional Bit 8 Insertion Control Bit (Sa8) 0 = do not insert data from the TR.TSa8 register into the transmit data stream 1 = insert data from the TR.TSa8 register into the transmit data stream Register Name: Register Description: Register Address: Bit # Name Default 7 ACNT7 0 TR.BAWC BERT Alternating Word-Count Rate DBh 6 ACNT6 0 5 ACNT5 0 4 ACNT4 0 3 ACNT3 0 2 ACNT2 0 1 ACNT1 0 0 ACNT0 0
Bits 0 - 7: Alternating Word-Count Rate Bits 0 to 7 (ACNT0 to ACNT7). ACNT0 is the LSB of the 8-bit alternating word-count rate counter.
284 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 RPAT7 0 TR.BRP1 BERT Repetitive Pattern Set Register 1 DCh 6 RPAT6 0 5 RPAT5 0 4 RPAT4 0 3 RPAT3 0 2 RPAT2 0 1 RPAT1 0 0 RPAT0 0
Bits 0 - 7: BERT Repetitive Pattern Set Bits 0 to 7 (RPAT0 to RPAT7) RPAT0 is the LSB of the 32-bit repetitive pattern set.
Register Name: Register Description: Register Address: Bit # Name Default 7 RPAT15 0
TR.BRP2 BERT Repetitive Pattern Set Register 2 DDh 6 RPAT14 0 5 RPAT13 0 4 RPAT12 0 3 RPAT11 0 2 RPAT10 0 1 RPAT9 0 0 RPAT8 0
Bits 0 - 7: BERT Repetitive Pattern Set Bits 8 to 15 (RPAT8 to RPAT15) Register Name: Register Description: Register Address: Bit # Name Default 7 RPAT23 0 TR.BRP3 BERT Repetitive Pattern Set Register 3 DEh 6 RPAT22 0 5 RPAT21 0 4 RPAT20 0 3 RPAT19 0 2 RPAT18 0 1 RPAT17 0 0 RPAT16 0
Bits 0 - 7: BERT Repetitive Pattern Set Bits 16 to 23 (RPAT16 to RPAT23) Register Name: Register Description: Register Address: Bit # Name Default 7 RPAT31 0 TR.BRP4 BERT Repetitive Pattern Set Register 4 DFh 6 RPAT30 0 5 RPAT29 0 4 RPAT28 0 3 RPAT27 0 2 RPAT26 0 1 RPAT25 0 0 RPAT24 0
Bits 0 - 7: BERT Repetitive Pattern Set Bits 24 to 31 (RPAT24 to RPAT31). RPAT31 is the LSB of the 32-bit repetitive pattern set.
285 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 TC 0 TR.BC1 BERT Control Register 1 E0h 6 TINV 0 5 RINV 0 4 PS2 0 3 PS1 0 2 PS0 0 1 LC 0 0 RESYNC 0
Bit 7: Transmit Pattern Load (TC). A low-to-high transition loads the pattern generator with the pattern that is to be generated. This bit should be toggled from low to high whenever the host wishes to load a new pattern. Must be cleared and set again for subsequent loads. Bit 6: Transmit Invert-Data Enable (TINV) 0 = do not invert the outgoing data stream 1 = invert the outgoing data stream Bit 5: Receive Invert-Data Enable (RINV) 0 = do not invert the incoming data stream 1 = invert the incoming data stream Bits 2 - 4: Pattern Select Bits (PS0 to PS2) PS 2 0 0 0 0 1 1 1 1 PS1 0 0 1 1 0 0 1 1 PS0 0 1 0 1 0 1 0 1 Pattern Definition Pseudorandom 2E7 - 1 Pseudorandom 2E11 - 1 Pseudorandom 2E15 - 1 20 Pseudorandom pattern QRSS. A 2 - 1 pattern with 14 consecutive zero restrictions. Repetitive pattern Alternating word pattern Modified 55 octet (Daly) pattern. The Daly pattern is a repeating 55 octet pattern that is byte-aligned into the active DS0 time slots. The pattern is defined in an ATIS (Alliance for Telecommunications Industry Solutions) Committee T1 Technical Report Number 25 (November 1993). Pseudorandom 2E9 - 1
Bit 1: Load Bit and Error Counters (LC). A low-to-high transition latches the current bit and error counts into registers TR.BBC1/ TR.BBC2/ TR.BBC3/ TR.BBC4 and TR.BEC1/ TR.BEC2/ TR.BEC3 and clears the internal count. This bit should be toggled from low to high whenever the host wishes to begin a new acquisition period. Must be cleared and set again for subsequent loads. Bit 0: Force Resynchronization (RESYNC). A low-to-high transition forces the receive BERT synchronizer to resynchronize to the incoming data stream. This bit should be toggled from low to high whenever the host wishes to acquire synchronization on a new pattern. Must be cleared and set again for a subsequent resynchronization.
286 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 EIB2 0
TR.BC2 BERT Control Register 2 E1h 6 EIB1 0 5 EIB0 0 4 SBE 0 3 RPL3 0 2 RPL2 0 1 RPL1 0 0 RPL0 0
Bits 5 - 7: Error Insert Bits 0 to 2 (EIB0 to EIB2). Automatically inserts bit errors at the prescribed rate into the generated data pattern. Can be used for verifying error-detection features. EIB2 0 0 0 0 1 1 1 1 EIB1 0 0 1 1 0 0 1 1 EIB0 0 1 0 1 0 1 0 1 Error Rate Inserted No errors automatically inserted 10E-1 10E-2 10E-3 10E-4 10E-5 10E-6 10E-7
Bit 4: Single Bit-Error Insert (SBE). A low-to-high transition creates a single-bit error. Must be cleared and set again for a subsequent bit error to be inserted. Bits 0 - 3: Repetitive Pattern Length Bit 3 (RPL0 to RPL3). RPL0 is the LSB and RPL3 is the MSB of a nibble that describes how long the repetitive pattern is. The valid range is 17 (0000) to 32 (1111). These bits are ignored if the receive BERT is programmed for a pseudorandom pattern. To create repetitive patterns fewer than 17 bits in length, the user must set the length to an integer number of the desired length that is less than or equal to 32. For example, to create a 6-bit pattern, the user can set the length to 18 (0001) or to 24 (0111) or to 30 (1101). Length (bits) 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 RPL3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 RPL2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 RPL1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 RPL0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
287 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 BBC7 0 TR.BBC1 BERT Bit Count Register 1 E3h 6 BBC6 0 5 BBC5 0 4 BBC4 0 3 BBC3 0 2 BBC2 0 1 BBC1 0 0 BBC0 0
Bits 0 - 7: BERT Bit Counter Bits 0 to 7 (BBC0 to BBC7). BBC0 is the LSB of the 32-bit counter. Register Name: Register Description: Register Address: Bit # Name Default 7 BBC15 0 TR.BBC2 BERT Bit Count Register 2 E4h 6 BBC14 0 5 BBC13 0 4 BBC12 0 3 BBC11 0 2 BBC10 0 1 BBC9 0 0 BBC8 0
Bits 0 - 7: BERT Bit Counter Bits 8 to 15 (BBC8 to BBC15) Register Name: Register Description: Register Address: Bit # Name Default 7 BBC23 0 TR.BBC3 BERT Bit Count Register 3 E5h 6 BBC22 0 5 BBC21 0 4 BBC20 0 3 BBC19 0 2 BBC18 0 1 BBC17 0 0 BBC16 0
Bits 0 - 7: BERT Bit Counter Bits 16 to 23 (BBC16 to BBC23) Register Name: Register Description: Register Address: Bit # Name Default 7 BBC31 0 TR.BBC4 BERT Bit Count Register 4 E6h 6 BBC30 0 5 BBC29 0 4 BBC28 0 3 BBC27 0 2 BBC26 0 1 BBC25 0 0 BBC24 0
Bits 0 - 7: BERT Bit Counter Bits 24 to 31 (BBC24 to BBC31). BBC31 is the MSB of the 32-bit counter.
288 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 EC7 0 TR.BEC1 BERT Error-Count Register 1 E7h 6 EC6 0 5 EC5 0 4 EC4 0 3 EC3 0 2 EC2 0 1 EC1 0 0 EC0 0
Bits 0 - 7: Error Counter Bits 0 to 7 (EC0 to EC7). EC0 is the LSB of the 24-bit counter. Register Name: Register Description: Register Address: Bit # Name Default 7 EC15 0 TR.BEC2 BERT Error-Count Register 2 E8h 6 EC14 0 5 EC13 0 4 EC12 0 3 EC11 0 2 EC10 0 1 EC9 0 0 EC8 0
Bits 0 - 7: Error Counter Bits 8 to 15 (EC8 to EC15) Register Name: Register Description: Register Address: Bit # Name Default 7 EC23 0 TR.BEC3 BERT Error-Count Register 3 E9h 6 EC22 0 5 EC21 0 4 EC20 0 3 EC19 0 2 EC18 0 1 EC17 0 0 EC16 0
Bits 0 - 7: Error Counter Bits 16 to 23 (EC16 to EC23). EC0 is the MSB of the 24-bit counter.
289 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0
TR.BIC BERT Interface Control Register EAh 6 RFUS 0 5 -- 0 4 TBAT 0 3 TFUS 0 2 -- 0 1 BERTDIR 0 0 BERTEN 0
Bit 6: Receive Framed/Unframed Select (RFUS) 0 = BERT is not sent data from the F-bit position (framed) 1 = BERT is sent data from the F-bit position (unframed) Bit 4: Transmit Byte-Align Toggle (TBAT). A 0-to-1 transition forces the BERT to byte align its pattern with the transmit formatter. This bit must be transitioned in order to byte align the Daly pattern. Bit 3: Transmit Framed/Unframed Select (TFUS) 0 = BERT does not source data into the F-bit position (framed) 1 = BERT does source data into the F-bit position (unframed) Bit 1: BERT Direction (BERTDIR) 0 = network BERT transmits toward the network (TTIP and TRING) and receives from the network (RTIP and RRING). The BERT pattern can be looped back to the receiver internally by using the framer loopback function. 1 = system BERT transmits toward the system backplane (RSERO) and receives from the system backplane (TSERI). Bit 0: BERT Enable (BERTEN) 0 = BERT disabled 1 = BERT enabled
290 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 WNOE 0 TR.ERC Error-Rate Control Register EBh 6 -- 0 5 -- 0 4 CE 0 3 ER3 0 2 ER2 0 1 ER1 0 0 ER0 0
Bit 7: Write NOE Registers (WNOE). If the host wishes to update to the TR.NOEx registers, this bit must be toggled from a 0 to a 1 after the host has already loaded the prescribed error count into the TR.NOEx registers. The toggling of this bit causes the error count loaded into the TR.NOEx registers to be loaded into the error-insertion circuitry on the next clock cycle. Subsequent updates require that the WNOE bit be set to 0 and then 1 once again. Bit 4: Constant Errors (CE). When this bit is set high (and the ER0 to ER3 bits are not set to 0000), the errorinsertion logic ignores the number-of-error registers (TR.NOE1, TR.NOE2) and generates errors constantly at the selected insertion rate. When CE is set to 0, the TR.NOEx registers determine how many errors are to be inserted. Bits 0 - 3: Error-Insertion Rate Select Bits (ER0 to ER3) ER3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 ER2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 ER1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 ER0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Error Rate No errors inserted 1 in 16 1 in 32 1 in 64 1 in 128 1 in 256 1 in 512 1 in 1024 1 in 2048 1 in 4096 1 in 8192 1 in 16,384 1 in 32,768 1 in 65,536 1 in 131,072 1 in 262,144
291 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.NOE1 Number-of-Errors 1 ECh 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bits 0 - 7: Number-of-Errors Counter Bits 0 to 7 (C0 to C7). Bit C0 is the LSB of the 10-bit counter. Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.NOE2 Number-of-Errors 2 EDh 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 C9 0 0 C8 0
Bits 0 - 1: Number-of-Errors Counter Bits 8 to 9 (C8 to C9). Bit C9 is the MSB of the 10-bit counter.
292 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver 11.7.1 Number-of-Errors Left Register The host can read the TR.NOELx registers at any time to determine how many errors are left to be inserted. Register Name: Register Description: Register Address: Bit # Name Default 7 C7 0 TR.NOEL1 Number-of-Errors Left 1 EEh 6 C6 0 5 C5 0 4 C4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0
Bits 0 - 7: Number-of-Errors Left Counter Bits 0 to 7 (C0 to C7). Bit C0 is the LSB of the 10-bit counter. Register Name: Register Description: Register Address: Bit # Name Default 7 -- 0 TR.NOEL2 Number-of-Errors Left 2 EFh 6 -- 0 5 -- 0 4 -- 0 3 -- 0 2 -- 0 1 C9 0 0 C8 0
Bits 0 - 1: Number-of-Errors Left Counter Bits 8 to 9 (C8 to C9). Bit C9 is the MSB of the 10-bit counter.
293 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
12 FUNCTIONAL TIMING
12.1 Functional Serial I/O Timing
The Serial Interface provides flexible timing to interconnect with a wide variety of serial interfaces. TDEN is an input signal that can be used to enable or block the TSERO data. The "shaded bits" are not clocked by the DS33R11. The TDEN must occur one bit before the effected bit in the TSERO stream. Note that polarity of the TDEN is selectable through LI.TSLCR. In the figure below, TDEN is active low, allowing the bits to clock and inactive high, causing the next data bit not be clocked. TCLKE can be gapped as shown in the following figure. Similarly, the receiver function is governed by RCLKI, RDEN and RSERI. RSERI data will not be provided to the receiver for the bits blocked when RDEN is inactive. The RDEN polarity can be programmed by LI.RSLCR. The RDEN signal must be coincident with the RSERI bit that needs to be blocked.
Figure 12-1. Tx Serial Interface Functional Timing
TCLKE TDEN TCLK gapped TSERO TCLKE Gapped TSERO TSER
Figure 12-2. Rx Serial Interface Functional Timing
RCLKI RDEN RSERI RCLKI Gapped RSERI TSER
294 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver The DS33R11 provides the TBSYNC signal as a byte boundary indication to an external interface when X.86 (LAPS) functionality is selected. The functional timing of TBSYNC is shown in the following figure.TBSYNC is active high on the last bit of the byte being shifted out, and occurs every 8 bits. For the serial receiver interface, RBSYNC is used to provide byte boundary indication to the DS33R11 when X.86 (LAPS) mode is used. The functional timing is shown in Figure 12-3. In X.86 Mode, the receiver expects the RBSYNC byte indicator as shown in Figure 12-4.
Figure 12-3. Transmit Byte Sync Functional Timing
TCLKE TBYSYNC TSERO last bit 1st bit
Figure 12-4. Receive Byte Sync Functional Timing
RCLKI RBYSYNC RSERI last bit 1st bit
12.2 MII and RMII Interfaces
The MII Interface Transmit Port has its own TX_CLK and data interface. The data TXD [3:0] operates synchronously with TX_CLK. The LSB is presented first. TX_CLK should be 2.5MHz for 10Mbit/s operation and 25MHz for 100Mbit/s operation. TX_EN is valid at the same time as the first byte of the preamble. In DTE Mode TX_CLK is input from the external PHY. In DCE Mode, the DS33R11 provides TX_CLK, derived from an external reference (SYSCLKI).
Figure 12-5. MII Transmit Functional Timing
TX_CLK TXD[3:0] TX_EN P R E A E M B L E F C S
295 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver In Half-Duplex (DTE) Mode, the DS33R11 supports CRS and COL signals. CRS is active when the PHY detects transmit or receive activity. If there is a collision as indicated by the COL input, the DS33R11 will replace the data nibbles with jam nibbles. After a "random" time interval, the packet is retransmitted. The MAC will try to send the packet a maximum of 16 times. The jam sequence consists of 55555555h. Note that the COL signal and CRS can be asynchronous to the TX_CLK and are only valid in half duplex mode.
Figure 12-6. MII Transmit Half Duplex with a Collision Functional Timing
TX_CLK TXD[3:0] TX_EN CRS COL P R E A M B L E J J J J J J J J
Receive Data (RXD[3:0]) is clocked from the external PHY synchronously with RX_CLK. The RX_CLK signal is 2.5MHz for 10Mbit/s operation and 25MHz for 100Mbit/s operation. RX_DV is asserted by the PHY from the first nibble of the preamble in 100 Mbit/s operation or first nibble of SFD for 10 Mbit/s operation. The data on RXD[3:0] is not accepted by the MAC if RX_DV is low or RX_ERR is high (in DTE mode). RX_ERR should be tied low when in DCE Mode.
Figure 12-7. MII Receive Functional Timing
RX_CLK RXD[3:0] P R E A E M B L E F C S
In RMII Mode, TX_EN is high with the first bit of the preamble. The TXD[1:0] is synchronous with the 50MHz REF_CLK. For 10 Mbit/s operation, the data bit outputs are updated every 10 clocks.
Figure 12-8. RMII Transmit Interface Functional Timing
REFCLK TXD[1:0] TX_EN P R E A M B L E F C S
296 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver RMII Receive data on RXD[1:0] is expected to be synchronous with the rising edge of the 50 MHz REF_CLK. The data is only valid if CRS_DV is high. The external PHY asynchronously drives CRS_DV low during carrier loss.
Figure 12-9. RMII Receive Interface Functional Timing
REFCLK RXD[1:0] CRS_DV P R E A M B L E F C S
12.3
Transceiver T1 Mode Functional Timing
Figure 12-10. Receive-Side D4 Timing
FRAME# RFSYNC RSYNC 1 RSYNC 2 RSYNC
3
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
NOTE 1: RSYNC IN THE FRAME MODE (TR.IOCR1.5 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.6 = 0). NOTE 2: RSYNC IN THE FRAME MODE (TR.IOCR1.5 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.6 = 1). NOTE 3: RSYNC IN THE MULTIFRAME MODE (TR.IOCR1.5 = 1).
Figure 12-11. Receive-Side ESF Timing
FRAME# RSYNC
1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5
RFSYNC RSYNC RSYNC
2 3
NOTE 1: RSYNC IN FRAME MODE (TR.IOCR1.4 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.6 = 0). NOTE 2: RSYNC IN FRAME MODE (TR.IOCR1.4 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.6 = 1). NOTE 3: RSYNC IN MULTIFRAME MODE (TR.IOCR1.4 = 1).
297 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-12. Receive-Side Boundary Timing (Elastic Store Disabled)
RCLKO
CHANNEL 23 CHANNEL 24
LSB MSB LSB
CHANNEL 1
RSERO RSYNC RFSYNC RSIG RCHCLK RCHBLK1
F
MSB
CHANNEL 23 A B C/A D/B
CHANNEL 24 A B C/A D/B
CHANNEL 1 A
NOTE 1: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
Figure 12-13. Receive-Side 1.544MHz Boundary Timing (Elastic Store Enabled)
RSYSCLK
CHANNEL 23 CHANNEL 24
LSB MSB LSB
CHANNEL 1
RSERO RSYNC1 RMSYNC RSYNC2 RSIG RCHCLK RCHBLK
3
F
MSB
CHANNEL 23 A B C/A D/B
CHANNEL 24 A B C/A D/B
CHANNEL 1 A
NOTE 1: RSYNC IS IN THE OUTPUT MODE (TR.IOCR1.4 = 0). NOTE 2: RSYNC IS IN THE INPUT MODE (TR.IOCR1.4 = 1). NOTE 3: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
298 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-14. Receive-Side 2.048MHz Boundary Timing (Elastic Store Enabled)
RSYSCLK RSER O
1 CHANNEL 31
LSB MSB
CHANNEL 32
LSB F
5
CHANNEL 1
RSYNC
2
RMSYNC
RSYNC
3 CHANNEL 31 B C/A D/B CHANNEL 32 B C/A D/B CHANNEL 1
RSIG RCHCLK RCHBLK
4
A
A
NOTE 1: RSERO DATA IN CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 ARE FORCED TO 1. NOTE 2: RSYNC IS IN THE OUTPUT MODE (TR.IOCR1.4 = 0). NOTE 3: RSYNC IS IN THE INPUT MODE (TR.IOCR1.4 = 1). NOTE 4: RCHBLK IS FORCED TO 1 IN THE SAME CHANNELS AS RSERO (SEE NOTE 1). NOTE 5: THE F-BIT POSITION IS PASSED THROUGH THE RECEIVE-SIDE ELASTIC STORE.
Figure 12-15. Transmit-Side D4 Timing
FRAME# TSYNC
1
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
TSSYNC TSYNC TSYNC
2 3
NOTE 1: TSYNC IN THE FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.1 = 0). NOTE 2: TSYNC IN THE FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.1 = 1). NOTE 3: TSYNC IN THE MULTIFRAME MODE (TR.IOCR1.2 = 1).
299 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-16. Transmit-Side ESF Timing
FRAME# TSYNC1 TSSYNC TSYNC
2 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5
TSYNC
NOTE 1: TSYNC IN FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.3 = 0). NOTE 2: TSYNC IN FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.3 = 1). NOTE 3: TSYNC IN MULTIFRAME MODE (TR.IOCR1.2 = 1).
Figure 12-17. Transmit-Side Boundary Timing (with Elastic Store Disabled)
TCLKT
CHANNEL 1 CHANNEL 2
LSB MSB LSB MSB
TSERI TSYNC1 TSYNC2
LSB
F
MSB
CHANNEL 1
CHANNEL 2
C/A D/B A B C/A D/B
TSIG TCHCLK TCHBLK 3
D/B
A
B
NOTE 1: TSYNC IS IN THE OUTPUT MODE (TR.IOCR1.1 = 1). NOTE 2: TSYNC IS IN THE INPUT MODE (TR.IOCR1.1 = 0). NOTE 3: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 2.
300 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-18. Transmit-Side 1.544MHz Boundary Timing (Elastic Store Enabled)
TSYSCLK
CHANNEL 23 CHANNEL 24
LSB MSB LSB F MSB
CHANNEL 1
TSERI TSSYNC
CHANNEL 23
CHANNEL 24
C/A D/B A B C/A D/B
CHANNEL 1
A
TSIG TCHCLK TCHBLK 1
A
B
NOTE 1: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24 (IF THE TPCSI BIT IS SET, THEN THE SIGNALING DATA AT TSIG IS IGNORED DURING CHANNEL 24).
Figure 12-19. Transmit-Side 2.048MHz Boundary Timing (Elastic Store Enabled)
TSYSCLK
CHANNEL 31 CHANNEL 32
LSB MSB LSB
CHANNEL 1
TSERI
1
F
4
TSSYNC
CHANNEL 31 CHANNEL 32
C/A D/B A B C/A D/B
CHANNEL 1
A
TSIG TCHCLK TCHBLK 2,3
A
B
NOTE 1: TSERI DATA IN CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 IS IGNORED. NOTE 2: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 31 (IF THE TPCSI BIT IS SET, THEN THE SIGNALING DATA AT TSIG WILL BE IGNORED). NOTE 3: TCHBLK IS FORCED TO 1 IN THE SAME CHANNELS AS TSERI IS IGNORED (SEE NOTE 1). NOTE 4: THE F-BIT POSITION FOR THE T1 FRAME IS SAMPLED AND PASSED THROUGH THE TRANSMIT-SIDE ELASTIC STORE INTO THE MSB BIT POSITION OF CHANNEL 1. (NORMALLY, THE TRANSMIT-SIDE FORMATTER OVERWRITES THE F-BIT POSITION UNLESS THE FORMATTER IS PROGRAMMED TO PASS THROUGH THE F-BIT POSITION.)
301 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
12.4
E1 Mode
Figure 12-20. Receive-Side Timing
FRAME# RFSYNC RSYNC
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
RSYNC 2
NOTE 1: RSYNC IN FRAME MODE (TR.IOCR1.5 = 0). NOTE 2: RSYNC IN MULTIFRAME MODE (TR.IOCR1.5 = 1). NOTE 3: THIS DIAGRAM ASSUMES THE CAS MF BEGINS IN THE RAF FRAME.
Figure 12-21. Receive-Side Boundary Timing (with Elastic Store Disabled)
RCLKO
CHANNEL 32 CHANNEL 1
LSB
CHANNEL 2
RSERO RSYNC RFSYNC
CHANNEL 32
Si
1
A
Sa4 Sa5 Sa6 Sa7 Sa8 MSB
CHANNEL 1 C D
Note 4
RSIG RCHCLK RCHBLK
1
A
B
CHANNEL 2 A B
NOTE 1: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 1. NOTE 2: SHOWN IS A RNAF FRAME BOUNDARY. NOTE 3: RSIG NORMALLY CONTAINS THE CAS MULTIFRAME ALIGNMENT NIBBLE (0000) IN CHANNEL 1.
302 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-22. Receive-Side Boundary Timing, RSYSCLK = 1.544MHz (E-Store Enabled)
RSYSCLK
CHANNEL 23/31 CHANNEL 24/32
LSB
CHANNEL 1/2
RSERO
1
LSB MSB
F
MSB
RSYNC2 RMSYNC RSYNC
3
RCHCLK RCHBLK
4
NOTE 1: DATA FROM THE E1 CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 IS DROPPED (CHANNEL 2 FROM THE E1 LINK IS MAPPED TO CHANNEL 1 OF THE T1 LINK, ETC.) AND THE F-BIT POSITION IS ADDED (FORCED TO ON 1). NOTE 2: RSYNC IN THE OUTPUT MODE (TR.IOCR1.4 = 0). NOTE 3: RSYNC IN THE INPUT MODE (TR.IOCR1.4 = 1). NOTE 4: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
Figure 12-23. Receive-Side Boundary Timing, RSYSCLK = 2.048MHz (E-Store Enabled)
RSYSCLK
CHANNEL 31 CHANNEL 32
LSB MSB LSB MSB
CHANNEL 1
RSERO RSYNC1 RMSYNC
RSYNC
2
RSIG RCHCLK RCHBLK
3
A
CHANNEL 31 C B D
A
CHANNEL 32 C B D
CHANNEL 1
Note 4
NOTE 1: RSYNC IS IN THE OUTPUT MODE (TR.IOCR1.4 = 0). NOTE 2: RSYNC IS IN THE INPUT MODE (TR.IOCR1.4 = 1). NOTE 3: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 1. NOTE 4: RSIG NORMALLY CONTAINS THE CAS MULTIFRAME ALIGNMENT NIBBLE (0000) IN CHANNEL 1.
303 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-24. G.802 Timing, E1 Mode Only
TS # RSYNC TSYNC RCHCLK TCHCLK RCHBLK TCHBLK
31 32 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 0 1 2
RCLKO / RSYSCLK TCLKT / TSYSCLK
NOTE: RCHBLK OR TCHBLK PROGRAMMED TO PULSE HIGH DURING TIME SLOTS 1 THROUGH 15, 17 THROUGH 25, AND BIT 1 OF TIME SLOT 26.
CHANNEL 25 RSERO / TSERI RCHCLK / TCHCLK RCHBLK / TCHBLK
LSB MSB
CHANNEL 26
Figure 12-25. Transmit-Side Timing
FRAME# TSYNC
1 14 15 16 1 2 3 4 56 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10
TSSYNC TSYNC
2
NOTE 1: TSYNC IN FRAME MODE (TR.IOCR1.2 = 0). NOTE 2: TSYNC IN MULTIFRAME MODE (TR.IOCR1.2 = 1). NOTE 3: THIS DIAGRAM ASSUMES BOTH THE CAS MF AND THE CRC4 MF BEGIN WITH THE TAF FRAME.
304 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-26. Transmit-Side Boundary Timing (Elastic Store Disabled)
TCLKT
CHANNEL 1 CHANNEL 2
LSB MSB
TSERI TSYNC1 TSYNC2
LSB
Si
1
A
Sa4 Sa5 Sa6 Sa7 Sa8 MSB
CHANNEL 1
CHANNEL 2
A B C D
TSIG TCHCLK TCHBLK 3
D
NOTE 1: TSYNC IS IN THE OUTPUT MODE (TR.IOCR1.1 = 1). NOTE 2: TSYNC IS IN THE INPUT MODE (TR.IOCR1.1 = 0). NOTE 3: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 2. NOTE 5: THE SIGNALING DATA AT TSIG DURING CHANNEL 1 IS NORMALLY OVERWRITTEN IN THE TRANSMIT FORMATTER WITH THE CAS MF ALIGNMENT NIBBLE (0000). NOTE 6: SHOWN IS A TNAF FRAME BOUNDARY.
Figure 12-27. Transmit-Side Boundary Timing, TSYSCLK = 1.544MHz (Elastic Store Enabled)
TSYSCLK
CHANNEL 23 CHANNEL 24
LSB MSB LSB F MSB
CHANNEL 1
TSERI
1
TSSYNC TCHCLK TCHBLK
2
NOTE 1: THE F-BIT POSITION IN THE TSERI DATA IS IGNORED. NOTE 2: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
305 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-28. Transmit-Side Boundary Timing, TSYSCLK = 2.048MHz (Elastic Store Enabled)
TSYSCLK
CHANNEL 31 CHANNEL 32
LSB MSB LSB
CHANNEL 1
TSERI
1
F
4
TSSYNC
CHANNEL 31 CHANNEL 32
C D A B C D
CHANNEL 1
A
TSIG TCHCLK TCHBLK
A
B
NOTE 1: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 31.
306 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13 OPERATING PARAMETERS
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Lead with Respect to VSS (except VDD).....................................................-0.5V to +5.5V Supply Voltage (VDD3.3) Range with Respect to VSS................................................................-0.3V to +3.6V Supply Voltage (VDD1.8) with Respect to VSS..........................................................................-0.3V to +2.0V Ambient Operating Temperature Range.................................................................................-40C to +85C Junction Operating Temperature Range..............................................................................-40C to +125C Storage Temperature Range.............................................................................................-55C to +125C Soldering Temperature....................................................................See IPC/JEDEC J-STD-020 Specification
These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time can affect reliability. Ambient Operating Temperature Range is assuming the device is mounted on a JEDEC standard test board in a convection cooled JEDEC test enclosure. Note: The "typ" values listed below are not production tested.
Table 13-1. Recommended DC Operating Conditions
(VDD3.3 = 3.3V 5%, VDD1.8 = 1.8V 5%, Tj = -40C to +85C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Logic 1 Logic 0 Supply (VDD3.3) 5% Supply (VDD1.8) 5%
VIH VIL VDD3.3 VDD1.8
2.35 -0.3 3.135 1.71
3.300 1.8
3.465 +0.75 3.465 1.89
V V V V
Table 13-2. DC Electrical Characteristics
(VDD3.3 = 3.3V 5%, VDD1.8 = 1.8V 5%, Tj = -40C to +85C.) PARAMETER SYMBOL CONDITIONS I/O Supply Current (VDD3.3 = 3.465V) Core Supply Current (VDD1.8 = 1.89V) Lead Capacitance Input Leakage Output Leakage (when High-Z) (IOH = -4.0mA) (IOL = +4.0mA) Output Voltage (IOH = -8.0mA) (IOL = +12.0mA) Input Voltage IDDIO IDDCORE CIO IIL IILP ILO VOH VOL VOH VOL VIL VIH (Notes 1, 2) (Notes 1, 2) (Note 3) -10 -50 -10 2.35 2.35 0.75 0.75 2.35
MIN TYP MAX UNITS
100 30 7 +10 -10 +10 0.75
mA mA pF
mA mA
All outputs All outputs REF_CLKO TSERO
V
V
Note 1: Note 2: Note 3:
Typical power consumption is approximately 400mW. All outputs loaded with rated capacitance; all inputs between VDD and VSS; inputs with pullups connected to VDD. Value guaranteed by design (GBD).
307 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.1 Thermal Characteristics Table 13-3. Thermal Characteristics
PARAMETER MIN TYP MAX
Ambient Temperature (Note 1) Junction Temperature (Note 2) Theta-JA (qJA) in Still Air for 256-Pin 27mm BGA (Notes 2, 3)
Note 1: Note 2: Note 3:
-40C
+85C +125C +20.3C/W
The package is mounted on a four-layer JEDEC standard test board. Value guaranteed by design (GBD). Theta-JA (qJA) is the junction to ambient thermal resistance, when the package is mounted on a four-layer JEDEC standard test board.
Table 13-4. Theta-JA vs. Airflow
AIR FLOW THETA-JA 256-PIN (27mm) BGA 20.3C/W 17.9C/W 16.9C/W
0m/s (Note 1) 1m/s (Note 1) 2.5m/s (Note 1)
Note 1:
Value guaranteed by design (GBD).
308 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.2 MII Interface Table 13-5. Transmit MII Interface
(Note 1, Figure 13-1)
PARAMETER SYMBOL MIN 10Mbps TYP MAX MIN 100Mbps TYP MAX UNITS
TX_CLK Period TX_CLK Low Time TX_CLK High Time TX_CLK to TXD, TX_EN Delay
t1 t2 t3 t4 140 140 0
400 260 260 20 14 14 0
40 26 26 20
ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-1. Transmit MII Interface Timing
t1 t2 t3 t4
TX_CLK
TXD[3:0]
TX_EN
t4
309 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 13-6. Receive MII Interface
(Note 1, Figure 13-2)
PARAMETER SYMBOL MIN 10Mbps TYP MAX MIN 100Mbps TYP MAX UNITS
RX_CLK Period RX_CLK Low Time RX_CLK High Time RXD, RX_DV to RX_CLK Setup Time RX_CLK to RXD, RX_DV Hold Time
t5 t6 t7 t8 t9 140 140 5 5
400 260 260 14 14 5 5
40 26 26
ns ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-2. Receive MII Interface Timing
t5
RX_CLK
t8 t9
t7 t6
RXD[3:0]
t8 t9
RX_DV
310 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.3 RMII Interface Table 13-7. Transmit RMII Interface
(Note 1, Figure 13-3)
PARAMETER SYMBOL MIN 10Mbps TYP 50MHz 50ppm MAX MIN 100Mbps TYP 50MHz 50ppm MAX UNITS
REF_CLK Frequency REF_CLK Period REF_CLK Low Time REF_CLK High Time REF_CLK to TXD, TX_EN Delay t1 t2 t3 t4 7 7 5
20 13 13 10 7 7 5
20 13 13 10
ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-3. Transmit RMII Interface Timing
t1 t2 t3 t4
REF_CLK
TXD[1:0]
TX_EN
t4
311 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 13-8. Receive RMII Interface
(Note 1, Figure 13-4)
PARAMETER SYMBOL MIN 10Mbps TYP MAX MIN 100Mbps TYP MAX UNITS
REF_CLK Frequency REF_CLK Period REF_CLK Low Time REF_CLK High Time RXD, CRS_DV to REF_CLK Setup Time REF_CLK to RXD, CRS_DV Hold Time t1 t2 t3 t8 t9 7 7 5 5
50MHz 50ppm 20 13 13 7 7 5 5
50MHz 50ppm 20 13 13
MHz ns ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-4. Receive RMII Interface Timing
t5
REF_CLK
t8 t9
t7 t6
RXD[3:0]
t8 t9
CRS_DV
312 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.4 MDIO Interface Table 13-9. MDIO Interface
(Note 1, Figure 13-5)
PARAMETER SYMBOL MIN TYP MAX UNITS
MDC Frequency MDC Period MDC Low Time MDC High Time MDC to MDIO Output Delay MDIO Setup Time MDIO Hold Time
Note 1: Timing parameters in this table are guaranteed by design (GBD).
1.67 t1 t2 t3 t4 t5 t6 540 270 270 20 10 20 600 300 300 660 330 330 10
MHz ns ns ns ns ns ns
Figure 13-5. MDIO Interface Timing
t1 t2 t3 t4
MDC
MDIO
MDC
t5 t6
MDIO
313 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.5 Transmit WAN Interface Table 13-10. Transmit WAN Interface
(Note 1, Figure 13-6) PARAMETER TCLKE Frequency TCLKE Period TCLKE Low Time TCLKE High Time TCLKE to TSERO Output Delay TBSYNC Setup Time TBSYNC Hold Time TCLKE to TDEN Output Delay t1 t2 t3 t4 t5 t6 t7 19.2 8 8 3 7 7 3.5 10
SYMBOL MIN TYP MAX UNITS
52
MHz ns ns ns ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-6. Transmit WAN Interface Timing
t1 t2 t3 t4
TCLKE
TSERO
t7
TDEN
t5
TBSYNC
t6
314 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.6 Receive WAN Interface Table 13-11. Receive WAN Interface
(Note 1, Figure 13-7) PARAMETER RCLKI Frequency RCLKI Period RCLKI Low Time RCLKI High Time RSERI Setup Time RDEN Setup Time RBSYNC Setup Time RDEN Setup Time RBSYNC Setup Time RSERI Hold Time RBSYNC Hold Time RDEN Hold Time RBSYNC Hold Time
SYMBOL MIN TYP MAX 52 UNITS
MHz ns ns ns ns ns ns ns ns ns ns ns ns
t1 t2 t3 t4 t4 t4 t4 t4 t5 t5 t5 t5
19.2 8 8 7 7 7 7 7 2 2 2 2
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-7. Receive WAN Interface Timing
t1 t2 t3
t4 t5
RCLKI
RSERI
t4 t5
RDEN
t4 t5
RBSYNC
315 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.7 SDRAM Timing Table 13-12. SDRAM Interface Timing
(Note 1, Figure 13-8)
PARAMETER SYMBOL MIN 100 MHz TYP MAX UNITS
SDCLKO Period SDCLKO Duty Cycle SDCLKO to SDATA Valid Write to SDRAM SDCLKO to SDATA Drive On Write to SDRAM SDCLKO to SDATA Invalid Write to SDRAM SDCLKO to SDATA Drive Off Write to SDRAM SDATA to SDCLKO Setup Time Read from SDRAM SDCLKO to SDATA Hold Time Read from SDRAM SDCLKO to SRAS, SCAS, SWE, SDCS Active Read or Write to SDRAM SDCLKO TO SRAS, SCAS, SWE, SDCS Inactive Read or Write to SDRAM SDCLKO to SDA, SBA Valid Read or Write to SDRAM SDCLKO TO SDA, SBA Invalid Read or write to SDRAM SDCLKO to SDMASK Valid Read or write to SDRAM SDCLKO TO SDMASK Invalid Read or write to SDRAM
t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14
9.7 4
10
10.3 6 7
ns ns ns ns ns
4 3 4 2 2 5 2 7 2 5 2
ns ns ns ns ns ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
316 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-8. SDRAM Interface Timing
t1
SDCLKO (output) SDATA (output)
t2 t3 t5
t4 t7 t8
t6
SDATA (input)
t9 t10
SRAS, SCAS, SWE, SDCS (output) SDA, SBA (output)
t11
t12
t13
t14
SDMASK (output)
317 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.8 Microprocessor Bus AC Characteristics Table 13-13. AC Characteristics--Microprocessor Bus Timing
(VDD3.3 = 3.3V 5%, VDD1.8 = 1.8V 5%, Tj = -40C to +85C.) (Note 1, Figure 13-9, Figure 13-10, Figure 13-11, and Figure 13-12)
PARAMETER SYMBOL MIN TYP MAX UNITS
Setup Time for A[12:0] Valid to CS Active Setup Time for CS Active to Either RD or WR Active Delay Time from either RD or DS Active to DATA[7:0] Valid Hold Time from either RD or WR Inactive to CS Inactive Hold Time from CS or RD or DS Inactive to DATA[7:0] Tri-State Wait Time from RW Active to Latch Data Data Set Up Time to DS Active Data Hold Time from RW Inactive Address Hold from RW Inactive Write Access to Subsequent Write/Read Access Delay Time
Note 1: Timing parameters in this table are guaranteed by design (GBD).
t1 t2 t3 t4 t5
t6
0 0 75 0 5 80 10 2 0 80 20
ns ns ns ns ns ns ns ns ns ns
t7 t8 t9 t10
318 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-9. Intel Bus Read Timing (MODEC = 00)
t9
ADDR[12:0]
Address Valid
DATA[7:0]
Data Valid
t5
WR
t1
CS
t2 t3 t4 t10
RD
Figure 13-10. Intel Bus Write Timing (MODEC = 00)
t9
ADDR[12:0]
Address Valid
DATA[7:0]
t7 t8
RD
t1
CS/CST
t2 WR t6 t4 t10
319 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-11. Motorola Bus Read Timing (MODEC = 01)
t9
ADDR[12:0]
Address Valid
DATA[7:0]
Data Valid
t5
RW
t1
CS/CST
t2 t3 t4 t10
DS
Figure 13-12. Motorola Bus Write Timing (MODEC = 01)
t9
ADDR[12:0]
Address Valid
DATA[7:0]
t7 t8
RW
t1
CS/CST
t2 t6 t4 t10
DS
320 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.9 AC Characteristics: Receive-Side Table 13-14. AC Characteristics: Receive Side
(VDD = 3.3V 5%, TA = -40C to +85C.) (Note 1, Figure 13-3, Figure 13-14, and Figure 13-15) PARAMETER RDCLKO Period SYMBOL tLP tLH tLL tLH tLL tCP tCH tCL tSP tSH tSL tSU tPW tSU tHD tR, tF tDD tD1 tD2 tD3 tD4 (Note 4) (Note 5) 20 20 20 50 20 20 22 50 50 50 22 22 20 20 (Note 2) (Note 2) (Note 3) (Note 3) 200 200 150 150 CONDITIONS MIN TYP 488 (E1) 648 (T1) 0.5 tLP 0.5 tLP 0.5 tLP 0.5 tLP 488 (E1) 648 (T1) 0.5 tCP 0.5 tCP 648 488 0.5 tSP 0.5 tSP ns ns ns ns ns ns ns ns ns ns ns ns ns MAX UNITS ns
RDCLKO Pulse Width RDCLKO Pulse Width RDCLKI Period RDCLKI Pulse Width RSYSCLK Period RSYSCLK Pulse Width RSYNC Setup to RSYSCLK Falling RSYNC Pulse Width RPOSI/RNEGI Setup to RDCLKI Falling RPOSI/RNEGI Hold from RDCLKI Falling RSYSCLK, RDCLKI Rise and Fall Times Delay RDCLKO to RPOSO, RNEGO Valid Delay RCLKO to RSERO, RDATA, RSIG Valid Delay RCLKO to RCHCLK, RSYNC, RCHBLK, RFSYNC Delay RSYSCLK to RSERO, RSIG Valid Delay RSYSCLK to RCHCLK, RCHBLK, RMSYNC, RSYNC
Note 2: Jitter attenuator enabled in the receive path.
ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD). Note 3: Jitter attenuator disabled or enabled in the transmit path. Note 4: RSYSCLK = 1.544MHz. Note 5: RSYSCLK = 2.048MHz.
321 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-13. Receive-Side Timing
RCLKO t D1 RSERO / RDATA / RSIG RSYNC 1 RFSYNC / RMSYNC
t D2
1ST FRAME BIT
t D2 t D2
RCHCLK t D2 RCHBLK
NOTE 1: RSYNC IS IN THE OUTPUT MODE. NOTE 2: NO RELATIONSHIP BETWEEN RCHCLK AND RCHBLK AND OTHER SIGNALS IS IMPLIED.
322 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-14. Receive-Side Timing, Elastic Store Enabled
tR tF t SL t SH t SP
RSYSCLK
t D3
RSERO / RSIG
t D4
SEE NOTE 3
RCHCLK
t D4
RCHBLK
t D4
RMSYNC RSYNC 1 2
t D4 t HD t SU
RSYNC
NOTE 1: RSYNC IS IN THE OUTPUT MODE. NOTE 2: RSYNC IS IN THE INPUT MODE. NOTE 3: F-BIT WHEN MSTRREG.1 = 0, MSB OF TS0 WHEN MSTREG.1 = 1.
323 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-15. Receive Line Interface Timing
t LL RDCLKO t DD RPOSO, RNEGO
t LH
t LP
tR RDCLKI
tF t SU
t CL
t CH
t CP
RPOSI, RNEGI t HD
324 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.10 AC Characteristics: Backplane Clock Timing Table 13-15. AC Characteristics: Backplane Clock Synthesis
(VDD = 3.3V 5%, TA = -40C to +85C.) (Note 1, (Figure 13-16)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Delay RCLKO to BPCLK
tD1
10
ns
Note: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-16. Receive Timing Delay RCLKO to BPCLK
RCLKO t D1 BPCLK
NOTE: IF RCLKO IS 1.544 MHZ, BPCLK WILL BE ASYNCHRONOUS.
325 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.11 AC Characteristics: Transmit Side Table 13-16. AC Characteristics: Transmit Side
(VDD = 3.3V 5%, TA = 0C to +85C.) (Note 1, Figure 13-17, Figure 13-18, and Figure 13-19) PARAMETER TCLKT Period TCLKT Pulse Width TDCLKI Period TDCLKI Pulse Width TSYSCLK Period TSYSCLK Pulse Width TSYNC or TSSYNC Setup to TCLKT or TSYSCLK Falling TSYNC or TSSYNC Pulse Width TSERI, TSIG, TDATA, TPOSI, TNEGI Setup to TCLKT, TSYSCLK, TDCLKI Falling TSERI, TSIG, TDATA Hold from TCLKT or TSYSCLK Falling TPOSI, TNEGI Hold from TDCLKI Falling TCLKT, TDCLKI or TSYSCLK Rise and Fall Times Delay TCLKO to TPOSO, TNEGO Valid Delay TCLKT to TESO, UT-UTDO Valid Delay TCLKT to TCHBLK, TCHCLK, TSYNC Delay TSYSCLK to TCHCLK, TCHBLK SYMBOL tCP tCH tCL tLP tLH tLL tSP tSP tSU tPW tSU tHD tHD tR, tF tDD tD1 tD2 tD3 20 20 (Note 2) (Note 3) 20 20 20 50 20 20 20 25 50 50 50 22 20 20 CONDITIONS MIN TYP (E1) 488 (E1) 648 (T1) 0.5 tCP 0.5 tCP 488 (E1) 648 (T1) 0.5 tLP 0.5 tLP 648 448 0.5 tSP 0.5 tSP MAX UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD). Note 2: TSYSCLK = 1.544MHz. Note 3: TSYSCLK = 2.048MHz.
326 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-17. Transmit-Side Timing
t CP tR TCLKT t D1 TESO TSERI / TSIG / TDATA t D2 TCHCLK TCHBLK t D2 TSYNC1 t SU TSYNC2 5 TLCLK t D2 t HD TLINK t SU t HD t D2 t SU t HD tF t CL t CH
NOTE 1: TSYNC IS IN THE OUTPUT MODE (IOCR1.1 = 1). NOTE 2: TSYNC IS IN THE INPUT MODE (IOCR1.1 = 0). NOTE 3: TSERI IS SAMPLED ON THE FALLING EDGE OF TCLKT WHEN THE TRANSMIT-SIDE ELASTIC STORE IS DISABLED. NOTE 4: TCHCLK AND TCHBLK ARE SYNCHRONOUS WITH TCLKT WHEN THE TRANSMIT-SIDE ELASTIC STORE IS DISABLED.
327 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-18. Transmit-Side Timing, Elastic Store Enabled
t SP tR TSYSCLK t SU TSERI t D3 TCHCLK t D3 TCHBLK t SU TSSYNC
NOTE 1: TSERI IS ONLY SAMPLED ON THE FALLING EDGE OF TSYSCLK WHEN THE TRANSMIT-SIDE ELASTIC STORE IS ENABLED. NOTE 2: TCHCLK AND TCHBLK ARE SYNCHRONOUS WITH TSYSCLK WHEN THE TRANSMIT-SIDE ELASTIC STORE IS ENABLED.
tF
t SL
t SH
t HD
t HD
Figure 13-19. Transmit Line Interface Timing
TDCLKO
TPOSO, TNEGO t DD tR TDCLKI t SU TPOSI, TNEGI t HD tF t LL t LP t LH
328 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.12 JTAG Interface Timing Table 13-17. JTAG Interface Timing
(VDD3.3 = 3.3V 5%,VDD1.8 = 1.8V 5%, Tj = -40C to +85C.) (Note 1, Figure 13-20)
PARAMETER SYMBOL MIN TYP MAX UNITS
JTCLK Clock Period JTCLK Clock High:Low Time (Note 2) JTCLK to JTDI, JTMS Setup Time JTCLK to JTDI, JTMS Hold Time JTCLK to JTDO Delay JTCLK to JTDO HIZ Delay
JTRST Width Low Time
t1 t2 : t3 t4 t5 t6 t7 t8 50 2 2 2 2 100
1000 500
ns ns ns ns 50 50 ns ns ns
Note 1: Timing parameters in this table are guaranteed by design (GBD). Note 2: Clock can be stopped high or low
Figure 13-20. JTAG Interface Timing Diagram
t1 t2 JTCLK t4 JTDI, JTMS t6 t5 t3
t7
JTD0
t8
JTRST
329 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14 JTAG INFORMATION
The DS33R11 contains two JTAG ports. Port 1 is for the Ethernet Mapper, and Port 2 is for the T1/E1/J1 Transceiver. The device supports the standard instruction codes SAMPLE:PRELOAD, BYPASS, and EXTEST. Optional public instructions included are HIGHZ, CLAMP, and IDCODE. See Table 20-1. The DS26521 contains the following as required by IEEE 1149.1 Standard Test Access Port and Boundary Scan Architecture. Test Access Port (TAP) TAP Controller Instruction Register Bypass Register Boundary Scan Register Device Identification Register The Test Access Port has the necessary interface pins: JTRST, JTCLK, JTMS, JTDI, and JTDO. See the pin descriptions for details. Refer to IEEE 1149.1-1990, IEEE 1149.1a-1993, and IEEE 1149.1b-1994 for details about the Boundary Scan Architecture and the Test Access Port.
Figure 14-1. JTAG Functional Block Diagram
Boundary Scan Register Identification Register Bypass Register Instruction Register Test Access Port Controller Select Tri-State
Mux
10K JTDI
10K JTMS JTCLK
10K JTRST JTDO
330 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14.1 JTAG TAP Controller State Machine Description
This section covers the details on the operation of the Test Access Port (TAP) Controller State Machine. The TAP controller is a finite state machine that responds to the logic level at JTMS on the rising edge of JTCLK.
TAP Controller State Machine
The TAP controller is a finite state machine that responds to the logic level at JTMS on the rising edge of JTCLK. See Figure 14-2 for a diagram of the state machine operation.
Test-Logic-Reset
Upon power up, the TAP Controller is in the Test-Logic-Reset state. The Instruction register will contain the IDCODE instruction. All system logic of the device will operate normally.
Run-Test-Idle
The Run-Test-Idle is used between scan operations or during specific tests. The Instruction register and test registers will remain idle.
Select-DR-Scan
All test registers retain their previous state. With JTMS LOW, a rising edge of JTCLK moves the controller into the Capture-DR state and will initiate a scan sequence. JTMS HIGH during a rising edge on JTCLK moves the controller to the Select-IR-Scan state.
Capture-DR
Data may be parallel-loaded into the test data registers selected by the current instruction. If the instruction does not call for a parallel load or the selected register does not allow parallel loads, the test register will remain at its current value. On the rising edge of JTCLK, the controller will go to the Shift-DR state if JTMS is LOW or it will go to the Exit1-DR state if JTMS is HIGH.
Shift-DR
The test data register selected by the current instruction is connected between JTDI and JTDO and will shift data one stage towards its serial output on each rising edge of JTCLK. If a test register selected by the current instruction is not placed in the serial path, it will maintain its previous state.
Exit1-DR
While in this state, a rising edge on JTCLK will put the controller in the Update-DR state, which terminates the scanning process, if JTMS is HIGH. A rising edge on JTCLK with JTMS LOW will put the controller in the PauseDR state.
Pause-DR
Shifting of the test registers is halted while in this state. All test registers selected by the current instruction will retain their previous state. The controller will remain in this state while JTMS is LOW. A rising edge on JTCLK with JTMS HIGH will put the controller in the Exit2-DR state.
Exit2-DR
A rising edge on JTCLK with JTMS HIGH while in this state will put the controller in the Update-DR state and terminate the scanning process. A rising edge on JTCLK with JTMS LOW will enter the Shift-DR state.
331 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Update-DR
A falling edge on JTCLK while in the Update-DR state will latch the data from the shift register path of the test registers into the data output latches. This prevents changes at the parallel output due to changes in the shift register.
Select-IR-Scan
All test registers retain their previous state. The instruction register will remain unchanged during this state. With JTMS LOW, a rising edge on JTCLK moves the controller into the Capture-IR state and will initiate a scan sequence for the instruction register. JTMS HIGH during a rising edge on JTCLK puts the controller back into the Test-Logic-Reset state.
Capture-IR
The Capture-IR state is used to load the shift register in the instruction register with a fixed value. This value is loaded on the rising edge of JTCLK. If JTMS is HIGH on the rising edge of JTCLK, the controller will enter the Exit1-IR state. If JTMS is LOW on the rising edge of JTCLK, the controller will enter the Shift-IR state.
Shift-IR
In this state, the shift register in the instruction register is connected between JTDI and JTDO and shifts data one stage for every rising edge of JTCLK towards the serial output. The parallel register, as well as all test registers, remains at their previous states. A rising edge on JTCLK with JTMS HIGH will move the controller to the Exit1-IR state. A rising edge on JTCLK with JTMS LOW will keep the controller in the Shift-IR state while moving data one stage thorough the instruction shift register.
Exit1-IR
A rising edge on JTCLK with JTMS LOW will put the controller in the Pause-IR state. If JTMS is HIGH on the rising edge of JTCLK, the controller will enter the Update-IR state and terminate the scanning process.
Pause-IR
Shifting of the instruction shift register is halted temporarily. With JTMS HIGH, a rising edge on JTCLK will put the controller in the Exit2-IR state. The controller will remain in the Pause-IR state if JTMS is LOW during a rising edge on JTCLK.
Exit2-IR
A rising edge on JTCLK with JTMS LOW will put the controller in the Update-IR state. The controller will loop back to Shift-IR if JTMS is HIGH during a rising edge of JTCLK in this state.
Update-IR
The instruction code shifted into the instruction shift register is latched into the parallel output on the falling edge of JTCLK as the controller enters this state. Once latched, this instruction becomes the current instruction. A rising edge on JTCLK with JTMS held low will put the controller in the Run-Test-Idle state. With JTMS HIGH, the controller will enter the Select-DR-Scan state.
332 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 14-2. TAP Controller State Diagram
1 Test Logic Reset 0 Run Test/ Idle 1 Select DR-Scan 0 1 Capture DR 0 Shift DR 1 Exit DR 0 Pause DR 1 0 Exit2 DR 1 Update DR 1 0 0 0 1 0 1 1 Select IR-Scan 0 Capture IR 0 Shift IR 1 Exit IR 0 Pause IR 1 Exit2 IR 1 Update IR 1 0 0 1 0 1
0
14.2 Instruction Register
The instruction register contains a shift register as well as a latched parallel output and is 3 bits in length. When the TAP controller enters the Shift-IR state, the instruction shift register is connected between JTDI and JTDO. While in the Shift-IR state, a rising edge on JTCLK with JTMS LOW will shift the data one stage towards the serial output at JTDO. A rising edge on JTCLK in the Exit1-IR state or the Exit2-IR state with JTMS HIGH will move the controller to the Update-IR state. The falling edge of that same JTCLK will latch the data in the instruction shift register to the instruction parallel output. Instructions supported by the DS26521 and its respective operational binary codes are shown in Table 14-1.
333 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 14-1. Instruction Codes for IEEE 1149.1 Architecture
INSTRUCTION SAMPLE:PRELOAD BYPASS EXTEST CLAMP HIGHZ IDCODE SELECTED REGISTER Boundary Scan Bypass Boundary Scan Bypass Bypass Device Identification INSTRUCTION CODES 010 111 000 011 100 001
SAMPLE:PRELOAD
This is a mandatory instruction for the IEEE 1149.1 specification. This instruction supports two functions. The digital I/Os of the device can be sampled at the boundary scan register without interfering with the normal operation of the device by using the Capture-DR state. SAMPLE:PRELOAD also allows the device to shift data into the boundary scan register via JTDI using the Shift-DR state.
BYPASS
When the BYPASS instruction is latched into the parallel instruction register, JTDI connects to JTDO through the one-bit bypass test register. This allows data to pass from JTDI to JTDO not affecting the device's normal operation.
EXTEST
This allows testing of all interconnections to the device. When the EXTEST instruction is latched in the instruction register, the following actions occur. Once enabled via the Update-IR state, the parallel outputs of all digital output pins are driven. The boundary scan register is connected between JTDI and JTDO. The Capture-DR will sample all digital inputs into the boundary scan register.
CLAMP
All digital outputs of the device will output data from the boundary scan parallel output while connecting the bypass register between JTDI and JTDO. The outputs will not change during the CLAMP instruction.
HIGHZ
All digital outputs of the device are placed in a high-impedance state. The BYPASS register is connected between JTDI and JTDO.
IDCODE
When the IDCODE instruction is latched into the parallel instruction register, the identification test register is selected. The device identification code is loaded into the identification register on the rising edge of JTCLK following entry into the Capture-DR state. Shift-DR can be used to shift the identification code out serially via JTDO. During Test-Logic-Reset, the identification code is forced into the instruction register's parallel output. The ID code will always have a `1' in the LSB position. The next 11 bits identify the manufacturer's JEDEC number and number of continuation bytes followed by 16 bits for the device and 4 bits for the version.
334 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14.3 JTAG ID Codes Table 14-2. ID Code Structure
DEVICE REVISION ID[31:28] DEVICE CODE ID[27:12] MANUFACTURER'S CODE ID[11:1] REQUIRED ID[0]
Ethernet Mapper T1/E1/J1 Transceiver
0000 0000
0000 0000 0110 0001 0000 0000 0001 0000
000 1010 0001 000 1010 0001
1 1
14.4 Test Registers
IEEE 1149.1 requires a minimum of two test registers: the bypass register and the boundary scan register. An optional test register has been included with the DS26521 design. This test register is the identification register and is used in conjunction with the IDCODE instruction and the Test-Logic-Reset state of the TAP controller.
14.4.1 Boundary Scan Register
This register contains both a shift register path and a latched parallel output for all control cells and digital I/O cells and is n bits in length.
14.4.2 Bypass Register
This is a single one-bit shift register used in conjunction with the BYPASS, CLAMP, and HIGHZ instructions, which provides a short path between JTDI and JTDO.
14.4.3 Identification Register
The identification register contains a 32-bit shift register and a 32-bit latched parallel output. This register is selected during the IDCODE instruction and when the TAP controller is in the Test-Logic-Reset state.
335 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14.5 JTAG Functional Timing
This functional timing for the JTAG circuits shows:
* * * * *
The JTAG controller starting from reset state. Shifting out the first 4 LSB bits of the IDCODE. Shifting in the BYPASS instruction (111) while shifting out the mandatory X01 pattern. Shifting the TDI pin to the TDO pin through the bypass shift register. An asynchronous reset occurs while shifting.
Figure 14-3. JTAG Functional Timing
(INST) (STATE) JTCLK JTRST JTMS JTDI JTDO Output Pin X X X Output pin level change if in "EXTEST" instruction mode X X X
Reset Run Test Idle Select DR Scan Capture DR
IDCODE
Shift DR Exit1 DR Update DR Select DR Scan Select IR Scan Capture IR Shift IR Exit1 IR Update IR Select DR Scan
BYPASS
Capture DR Shift DR
IDCODE
Test Logic Idle
336 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
15 PACKAGE INFORMATION
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/DallasPackInfo.)
15.1 Package Outline Drawing of 256-BGA (View from Bottom of Device)
337 of 338
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
16 REVISION HISTORY
REVISION 072105 DESCRIPTION New product release.
338 of 338
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product. No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Ma x i m I n t e g r a t e d P r o d u c t s , 1 2 0 S a n G a b r i e l D r i v e , S u n n y v a l e , C A 9 4 0 8 6 4 0 8 - 7 3 7 - 7 6 0 0
(c) 2005 Maxim Integrated Products * Printed USA
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.

▲Up To Search▲

Price & Availability of DS33R11

	To Download DS33R11 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .